EVO-IP HDMI® OVER IP Quick Start Guide Vanco Part Numbers: EVOIPTX1 Transmitter EVOIPRX1 Receiver EVOIPCTL1 Control Box www.vanco1.com • 800.626.
DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters. WARNING 1. Do not expose this unit to water, moisture, or excessive humidity. 2.
FEATURES INTRODUCTION The Evolution by Vanco EVO-IP HDMI over IP is a complete audio, video, and control product over ethernet system. As a whole, the system has the ability to send up to 1064 sources to 1064 displays along with IR and RS-232 pass-through, analog and digital audio breakouts on the send and receive ends, video up to 4K@60Hz and HDR10/Dolby Vision compatibility, with POE up to 330ft/100m when connected to a POE enabled switch off of a single Cat6 cable.
SPECIFICATIONS TECHNICAL SPECS - Transmitter and Receiver HDMI Compliance....................................................... HDMI HDCP Compliance....................................................... Yes Video Resolution......................................................... 4K@60Hz, 4:4:4; 4K@60Hz, 4:2:0 HDR10; 4K@30Hz, 4:4:4 HDR10; 4K@30Hz, 4:2:2 HDR10 and Dolby Vision; 4K@24Hz, 4:4:4 HDR10 and Dolby Vision Latency......................................................................
SPECIFICATIONS TECHNICAL SPECS - Control Box Role of Usage............................................................. Smart Controller Input......................................................................... 1 x RJ-45 Output....................................................................... 1 X HDMI HDMI Connector......................................................... Type A [19-pin female] RJ-45 Connector........................................................ WE/SS 8P8C USB (Female).........
PANEL DESCRIPTIONS Transmitting Unit 4 1 5 2 3 7 6 8 13 9 10 11 12 1. Link Indicator Light (lights up when connected and transmitting signal to ethernet switch) 2. Power Indicator Light (lights up when powered up by PoE or included power supply) 3. Info Indicator Light (shows data is being sent/received over the Cat cable/RJ45 port) 4. DB9 connector for RS-232 Control Pass-Through 5. IR-TX port (connect included IR Transmitter cable for source control) 6.
PANEL DESCRIPTIONS Receiving Unit 4 1 2 3 5 7 6 8 12 9 10 11 1. Link Indicator Light (lights up when connected and receiving signal from ethernet switch) 2. Power Indicator Light (lights up when powered up by PoE or included power supply) 3. Info Indicator Light (shows data is being sent/received over the Cat cable/RJ45 port) 4. DB9 connector for RS-232 Control Pass-Through 5. IR-TX port (connect included IR Transmitter cable for source control) 6.
PANEL DESCRIPTIONS Control Box 4 1 2 3 5 6 1. 5V Power Port (necessary as this unit requires external power) 2. Status Indicator Light (lights up when communicating with the system) 3. Power Indicator Light (lights up when powered up by included power supply) 4. HDMI OUT (connect to local display to show system IP information) 5. RJ45 port (connect to ethernet switch) 6. USB ports (reserved for future use) CONNECTION DIAGRAM 8 www.vanco1.
CONNECT AND OPERATE Before connecting and setting up the EVO-IP System, please enable settings within your ethernet switch that will allow you get the best performance possible. For additional information on which ethernet switches are compatible, please visit the product page at www.vanco1.com. For best results, ensure your ethernet switch has IGMP Snooping, Jumbo Frames, and POE enabled. 1. Connect the EVOIPTX1 and EVOIPRX1 transmitters and receivers to the network switch with a well terminated Cat5e/6.
6. Type in the username and password for the system Installer: Username and password is admin (full access to settings) User: Username and password is user (limited access to settings) 7. Go to the SETUP tab to further customize the name and ID for each device 10 www.vanco1.
LIMITED WARRANTY With the exceptions noted in the next paragraph, Vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of two years from the date of purchase. Should this product, in Vanco’s opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco.
® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.