DA468 INSTRUCTION MANUAL
vM DA468 STEREO DIGITAL / ANALOG CONVERTER vM INSTRUCTION MANUAL Thank you for having bought this Van Medevoort product. We wish you many happy listening hours. The manufacturer accepts no responsibility for any misunderstanding and/or misinterpretation or the consequences arising there from due to this instruction manual not being read correctly and followed properly. THE MANUAL It is essential to consult this manual before operating your Van Medevoort product.
vM DA468 STEREO DIGITAL / ANALOG CONVERTER BEFORE GETTING STARTED IN GENERAL When using your Van Medevoort product make sure that the following is observed: - The cooling air vents are not covered - The air can move freely around the product - The product is sited on a vibration-free surface - The product is not exposed to (very) high temperatures, cold, moist or dusty environments - Do not expose the product to direct sunlight - Do not expose the product to electrostatic discharges - Never put any type of
vM DA468 STEREO DIGITAL / ANALOG CONVERTER Controls Precautions Connections Maintenance and advice Technical Specifications Î 1 2 1. ON / OFF. Power switch. LED indication control. Fully red when switched ON, 50% red when in STANDBY mode (selected with the Remote Control). Above the LED you will find the Infra Red sensor for the Remote Control. The functions are “stand-by”, mute and input selection. The Remote Control handset is NOT supplied. Choose a learnable.
vM DA468 STEREO DIGITAL / ANALOG CONVERTER Controls Precautions Connections Maintenance and advice Technical Specifications • ONLY connect the converter to a (professionally installed) wall socket with earth or ground and the corresponding voltage setting, as indicated on the back. Any faulty connection will invalidate the warranty. • If it is necessary to replace the fuses, use only fuse(s) with the exact same value.
vM DA468 STEREO DIGITAL / ANALOG CONVERTER Controls Precautions Connections Maintenance and advice Technical Specifications Î Î 16 3 4 5 6 7 8 15 9 10 14 11 12 13 3. Input digital 1. The vM DA468 is provided with eight digital inputs, input 1 is for SPDif RCA. 4. Input digital 2. The vM DA468 is provided with eight digital inputs, input 2 is also for SPDif RCA. 5. Input digital 3.
vM DA468 STEREO DIGITAL / ANALOG CONVERTER 11. Output digital. Digital SPDif optical output, send through the signal of the USB or SPDif input which is switched on. 12. Output digital. Digital output RCA coaxial SPDif, send through the signal of the USB or SPDif input which is switched on. 13. IEC Power Chassis Connector. To be connected with the proper wall socket, which must be earthed or grounded. Every Van Medevoort product is optimized for your country’s electrical standards. e.g.
vM DA468 STEREO DIGITAL / ANALOG CONVERTER Controls Precautions Connections Maintenance and advice Technical Specifications • The SPDif in- and outputs are clocked for the different digital sources. By switching over between inputs, there can be a synchrony moment occur where by the converter stays in the mute mode. The DA468 can in that situation be reset by switching off with the power switch for aprox. 10 seconds and then again to on.
vM DA468 STEREO DIGITAL / ANALOG CONVERTER Controls Precautions Connections Maintenance and advice Technical Specifications input SPDif RCA / XLR 24 bit / 192 kHz 75 Ohms / 110 Ohms input SPDif optical 24 bit / 96 kHz input Q-Link 16 bit / 44.1 kHz input USB 16 bit / 48 kHz SRC on all inputs 24 bit / 192 kHz bandwidth analog 0,1 Hz – 100 kHz channel separation >110 dB distortion < 0,0018 % signal / noise ratio > 126 dB output impedance < 50 Ohms output voltage nom. 2.
vM DA468 STEREO DIGITAL / ANALOG CONVERTER INSTRUCTION LEAFLET FOR CONNECTING A CD-TRANSPORT VIA MULTI-LINK ON THE vM DA468 CONVERTER. Because there are different Multi-Link formats on the market we have upgraded the DA468 to switch the correct settings for input 6. You have to do this only once when installing, the system keeps this setting. Default is vM CT460.