Installation and User Guide CEILINGVIEW™ HD HIDEAWAY Ceiling Mounted Motorized Camera Lift System for the Vaddio™ ClearVIEW™ Family of HD PTZ Cameras ©2011 Vaddio - All Rights Reserved ● CeilingVIEW HD HideAway ● Document Number 342-0289 Rev.
CeilingVIEW HD HideAway Manual Inside Front Cover - Blank CeilingVIEW HD HideAway Manual, Document Number 342-0289 Rev.
CeilingVIEW HD HideAway Manual Vaddio CeilingVIEW HD HideAway Overview: Figure 1: Vaddio CeilingVIEW HD HideAway motorized camera lift system with a *Vaddio ClearVIEW HD-18AW Camera *Camera not included The Vaddio CeilingVIEW HD HideAway is a ceiling mounted motorized camera lift system that provides the ability to quietly lower a Vaddio ClearVIEW HD PTZ camera from the ceiling, retract it back into the ceiling and completely hide the camera.
CeilingVIEW HD HideAway Manual Unpacking Carefully remove all parts from the packaging and identify the following parts: CeilingVIEW HD HideAway, Part Number 999-2520-000 North America includes: One (1) CeilingVIEW HD HideAway Motorized Back Box Assembly One (1) White Trim Ring Assembly with five (5) white screws (6/32” x 1/2” Phillips flat head screws) One (1) Ceiling Tile Brace One (1) Lower Décor Plate One (1) CeilingVIEW HD HideAway Power Interface (998-2520-002) One (1) PowerRite 24VDC, 2A
CeilingVIEW HD HideAway Manual STEP BY STEP INSTALLATION INSTRUCTIONS: The CeilingVIEW HD HideAway is a motorized lift system enclosure specifically designed for Vaddio HD Cameras to be installed in a suspended acoustic ceiling tile. Recommended average room ceiling height range is between 8’ and 12’ (2.44m to 3.66m). It can also be used in larger group rooms, lecture halls or auditoriums depending on the system design requirements.
CeilingVIEW HD HideAway Manual Dip Switch Settings: Set the dip switches to the desired settings and then apply power to the system. To make any changes, remove power from the system, make the change and re-apply power to the system.
CeilingVIEW HD HideAway Manual Warning: Do not install the Ceiling Tile Brace in any direction where it does not reach each side of the 2 ft. suspended ceiling tile grid (see Figure 8).
CeilingVIEW HD HideAway Manual F. When the Ceiling Tile Brace has been placed in the desired position, trace the outline of the center opening of the Ceiling Tile Brace on the suspended ceiling tile (see Figure 5). G. Using a sharp utility knife, score the marked outline on the suspended ceiling tile. Carefully cut out the marked outline. Note: When cutting out the opening, cut out each of the four (4) corners of the outline to make the opening square (see Figure 6). H.
CeilingVIEW HD HideAway Manual L. Carefully lower and place the CeilingVIEW HD HideAway Motorized Back Box Assembly into the Ceiling Tile Brace opening. Figure 14: CeilingVIEW HD HideAway Motorized Back Box Assembly inserted into the Ceiling Tile Brace M. Check and verify that each of the four (4) individual support cables are all equal in tension and that the weight of the CeilingVIEW HD HideAway is supported mainly by the cables and not by the suspended ceiling tile.
CeilingVIEW HD HideAway Manual P. Attach the Lower Décor Plate to the bottom of the Camera Platform with three (3) white pan head screws. Camera mounting screw locations IR Sensor Circuit Board Cable Figure 15: Vaddio ClearVIEW HD-18 PTZ HD Camera mounted on the Camera Lift Platform Q. Figure 16: View of Camera Lift Platform from below ceiling with IR Sensor Circuit Board Cable exposed Attachment of the Ceiling Trim Ring Assembly to the CeilingVIEW HD HideAway Motorized Back Box Assembly: I.
CeilingVIEW HD HideAway Manual STEP #3: Connecting the Cat-5e cabling into the CeilingVIEW HD HideAway Motorized Back Box Assembly. Installation and Connection of the Cat-5e cabling to the CeilingVIEW HD HideAway: A. Insert the individually marked and tested three (3) Cat-5e cables necessary for connection to the CeilingVIEW HD HideAway Motorized Back Box Assembly through the provided ¾” conduit feed-through in the left side of the Back Box Assembly.
CeilingVIEW HD HideAway Manual The CeilingVIEW HD HideAway motorized camera lift system and the Vaddio ClearVIEW HD PTZ Camera can also be controlled by the Vaddio IR Remote Commander, which is included with all Vaddio ClearVIEW HD PTZ Cameras.
CeilingVIEW HD HideAway Manual Note: Anytime the PowerRite 24VDC, 2A Power Supply is disconnected from the CeilingVIEW HD HideAway Power Interface, the Boot-Up Procedure/Upper and Lower Limits Program in the CeilingVIEW HD HideAway will be repeated once power is reconnected. This procedure will take approximately one minute to complete.
CeilingVIEW HD HideAway Manual STEP 6: Controlling the CeilingVIEW HD HideAway with the following methods: 1) Vaddio IR Remote Commander (Setting the Upper and Lower Lift Stops) 2) Other Vaddio Products 3) Control Systems and Videoconferencing Codecs Vaddio IR Remote Commander Control: Overview: The Vaddio IR Remote Commander, included with all Vaddio ClearVIEW HD PTZ Cameras and packages, provides for simple IR remote control of the CeilingVIEW HD HideAway and the Vaddio ClearVIEW HD PTZ Camera functions.
CeilingVIEW HD HideAway Manual Instructions for Calibrating; Setting the Upper and Lower Lift Stops: A. Place the CeilingVIEW HD HideAway into the Calibration Mode: With the Blue Power LED on steady in the CeilingVIEW HD HideAway Trim Ring Assembly, press and hold the Calibration push button on the IR Circuit Board in the Trim Ring Assembly until Blue Power light is flashing.
CeilingVIEW HD HideAway Manual G. End the Calibration Mode in the CeilingVIEW HD HideAway: Press and hold the Calibration push button on the IR Circuit Board in the Trim Ring until the Blue Power light stops flashing and becomes steady blue.
CeilingVIEW HD HideAway Manual Control of the CeilingVIEW HD HideAway with other Vaddio Products: The CeilingVIEW HD HideAway is virtually transparent between the Vaddio Camera Control Consoles and Automated Content Presentation Systems and the Vaddio ClearVIEW HD PTZ Cameras. A. The CeilingVIEW HD HideAway has been programmed to power on and off when it receives the power on or off command via RS-232 from the Vaddio Camera Control Consoles and Automated Content Presentation Systems.
CeilingVIEW HD HideAway Manual Examples of Integrating the CeilingVIEW HD HideAway with Polycom® or TANDBERG (Cisco®) Codecs: Figure 28; Example 1: Polycom Codec: Integration of the CeilingVIEW HD HideAway Motorized Lift, CeilingVIEW HD HideAway Power Interface, Vaddio HD-19 PTZ Camera, Quick-Connect DVI/HDMI SR and a Polycom Codec with Polycom IR Remote Control. Three (3) Cat-5e Cables Up to 100’ (30.
CeilingVIEW HD HideAway Manual is lowered, the Vaddio IR Remote Commander must be pointed to the front of the Vaddio HD Camera in order to be received by the camera to control PTZ functions. 3) If IR Forwarding has been connected, you may need to point the Polycom Remote at the camera to provide codec control and PTZ control. However, the Vaddio Remote Control will be ignored including power on-off commands for lift operation.
CeilingVIEW HD HideAway Manual 2) Use the Power Button (green) on the Vaddio IR Remote Commander to power the CeilingVIEW HD HideAway on and lower the camera lift (see Figure 26). The Vaddio IR Remote Commander must be pointed to the CeilingVIEW HD HideAway (in the direction of the IR Sensor in the Trim Plate Assembly (see Figure 23) to activate the CeilingVIEW HD HideAway and lower the camera lift.
CeilingVIEW HD HideAway Manual Compliance and CE Declaration of Conformity Compliance testing was performed to the following regulations: FCC Part 15, Subpart B ICES-003, Issue 4: 2004 CISPR 22: 2009 European Standard EN 55103-1: 2009 European Standard EN 55103-2: 2009 EN 5502: 2006 + A1: 2007 (CISPR 22:2005/A1: 2005) EMC Directive 2004/108/EC Class A Class A Class A Class A Class A Class A Class A FCC Part 15 Compliance This equipment has been tested and found to comply with the limits for
CeilingVIEW HD HideAway Manual Warranty Information: Hardware* Warranty: One year limited warranty on all parts. Vaddio warrants this product against defects in materials and workmanship for a period of one year from the day of purchase from Vaddio. If Vaddio receives notice of such defects during the warranty period, they will, at their option, repair or replace products that prove to be defective. Please see Vaddio’s Service Terms and Conditions at vaddio.com for specific details and policies.
CeilingVIEW HD HideAway Manual Inside Rear Cover - Blank CeilingVIEW HD HideAway Manual, Document Number 342-0289 Rev.
CeilingVIEW HD HideAway Manual 9433 Science Center Drive, Minneapolis, MN 55428 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2011 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, CeilingVIEW, Quick-Connect, ProductionVIEW, ClearVIEW, EZCamera, AutoPresenter, HSDS and PowerRite are registered trademarks of Vaddio.