4KEX300-F HDMI2.
Disclaimers The information in this manual has been carefully checked and is believed to be accurate. AV Access Technology Limited assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. AV Access Technology Limited assumes no responsibility for any inaccuracies that may be contained in this document. AV Access Technology Limited also makes no commitment to update or to keep current the information contained in this document.
Important Safety Instructions • Do not expose this device to rain, moisture, dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the device. • Do not install or place this unit in a bookcase, built-in cabinet, or in another confined space. Ensure the unit is well ventilated. • To prevent risk of electric shock or fire hazard due to overheating, do not obstruct the unit’s ventilation openings with newspapers, tablecloths, curtains, or similar items.
Table of Contents Introduction ���������������������������������������������������������������������������������������������������������� 2 Overview �������������������������������������������������������������������������������������������������������������������������������������� 2 Features ���������������������������������������������������������������������������������������������������������������������������������������� 2 Package Contents ����������������������������������������������������������
Introduction Introduction Overview 4KEX300-F is a slim HDMI transmitter receiver set. It supports resolutions up to 4K@60Hz 4:4:4 8bit and HDCP 2.2, transporting HDMI signals up to 1000ft/300m over a duplex OM3 multi-mode optical fiber cable. 4KEX300-F supports bi-directional IR/RS232 pass through via DIP Switch settings, enabling users to control the source or display devices at either the transmitter or receiver side with ease. The transmitter and receiver are easy to install.
Introduction Package Contents Before you start the installation of the product, please check the package contents: • Transmitter 4KEX300-F x 1 • Receiver 4KEX300-F x 1 • 10Gbps 850nm MM SFP+ Module x 2 • Power Supply (DC 12V 0.5A) x 2 • IR Emitter x 1 • Broadband IR Receiver (30-50 KHz) x 1 • Phoenix Male Connector (3.5mm, 3 Pins) x 2 • Mounting Bracket x 4 • User Manual x 1 www.avaccess.
Introduction Panel Front Panel Transmitter/Receiver 1 No. Name 1 Power LED 2 Status LED 2 3 Description On: The device is powered on. Off: The device is powered off. Blinking: The device is working properly. Off: The device is not working properly. On: HDCP protected content is being transmitted. 3 HDCP LED Blinking: Non-HDCP protected content is being transmitted. Off: No content is being transmitted. On: The link between transmitter and receiver is normal.
Introduction Rear Panel Transmitter 1 2 3 4 5 No. Name Description 1 DC 12V DC 12V power input 2 HDMI In Connect to an HDMI source device. 3 Optical Out 4 RS232 5 IR In 6 IR Out 6 7 Connect to the Optical In port of the receiver via a duplex OM3 multimode optical fiber cable. For RS232 pass through Connect to the supplied IR receiver. Secure the IR receiver with adhesive. Connect to the supplied IR emitter.
Introduction Receiver 1 2 3 4 5 6 No. Name Description 1 DC 12V DC 12V power input 2 HDMI Out Connect to an HDMI display device. 3 Optical In 4 RS232 5 IR In 6 IR Out 7 Connect to the Optical Out port of the transmitter via a duplex OM3 multi-mode optical fiber cable. For RS232 pass through Connect to the supplied IR receiver. Secure the IR receiver with adhesive. Connect to the supplied IR emitter. Secure the IR emitter on the IR receiving sensor of display device with adhesive.
Installation Instructions Installation Instructions The product package includes one IR emitter and one IR receiver. Please refer to the following two applied installations. Applied installation 1: Power Supply DVD 7 The IR emitter head should Connect the 8 power supply 1 Connect the HDMI source be secured over the center of the DVD IR window. 6 Connect the IR emitter Transmitter Connect the transmitter 2 and receiver via a duplex OM3 fiber cable. Ensure its length is within 1000ft/300m.
Installation Instructions Applied installation 2: Power Supply Connect the 8 power supply TV Remote DVD 1 7 Connect the Connect the HDMI source Transmitter IR Receiver Connect the transmitter 2 and receiver via a duplex OM3 fiber cable. Ensure its length is within 1000ft/300m.
RS232 Pass Through RS232 Pass Through The RS232 ports provide a channel to pass through protocol commands to control third party devices such as your source or display. Switch the panel DIP Switch to RS232, and then connect RS232-enabled devices (such as a computer and a projector) to the transmitter and receiver respectively via RS232 cables. Please refer to the following pin definition of RS232 during your installation.
Specification Specification Technical Video Signal Type HDMI 2.0 with HDCP 2.2 800x6008, 1024x7688, 1280x7688, 1280x8008, 1280x9608, 1280x10248, 1360x7688, 1366x7688, 1440x9008, 1600x9008, 1600x12008, 1680x10508, Input/Output Resolution Supported 1920x10808, 1920x12008, 3840x2160P2,3,5,6,8, 4096x2160P2,3,5,6,8 1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz, 4 = at 29.97 Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94 Hz, 8 = at 60 Hz Audio Format Stereo, PCM2.0/5.1/7.
Specification Power Consumption Transmitter: 3.9W (Maximum) Receiver: 3.5W Device Dimensions 5.91'' x 0.79'' x 2.93'' (W x H x D) (150 mm ×20 mm × 74.4 mm) Product Net Weight Transmitter: 0.66lb (0.30kg) Receiver: 0.66lb (0.30kg) Cable Specifications: Cable Type HDMI Range Supported Video Input/Output: 49ft (15m) 1080P@60Hz Input/Output: 33ft (10m) 4K@30Hz Input: 10ft (3m) 4K@60Hz 4:4:4 8bit Output: 16ft (5m) Optical Fiber 1000ft (300m) www.avaccess.
Trouble Shooting Trouble Shooting Steps of Regular Troubleshooting Routine 1. Power: Please make sure all devices are powered on (the source, extender set and display). 2. Indicator: Please make sure LED indicators of the transmitter and receiver are normal according to user manual. 3. Devices: Please make sure picture can be shown normally when connecting source to display devices directly. 4. Cable: Plug in and out the HDMI/fiber cable or try another HDMI/fiber cable.
Trouble Shooting and ensure the cable length is within 1000ft/300m. • HDCP indicator should be solid on or blinking. If it is off, it means no signal pass through. Please check if the HDMI cables are well connected to the source and display, and the optical fiber cable that connects transmitter to receiver is normal. Try a better HDMI cable or fiber cable. 2.
Warranty Warranty Products are backed by a limited 3-year parts and labor warranty. For the following cases AV Access Technology Limited shall charge for the service(s) claimed for the product if the product is still remediable and the warranty card becomes unenforceable or inapplicable. 1. The original serial number (specified by AV Access Technology Limited) labeled on the product has been removed, erased, replaced, defaced or is illegible. 2. The warranty has expired. 3.
AV Access Technology Limited V1.0.