User's Manual
Table Of Contents
- Product Summary
- Component
- Function
- Wire Gauge (Unshielded or Shielded)
- Max. Wire Length Between Module and Concord Panel
- Figure 2. Mounting on or Near Metal
- Tools and Supplies
- Installation
- Figure 3. Removing the Cover
- To mount the module on a wall:
- 1. Remove the panel AC power transformer and disconnect the backup battery.
- 2. Remove the module cover and set it aside (Figure 3).
- 3. Hold the base against the mounting surface and mark the three mounting holes (Figure 1). Remem...
- 4. Drill holes and insert the appropriate anchors.
- 5. Secure the back-plate to the wall with included panhead screws.
- To mount the module in a Concord panel cabinet:
- 1. Remove the panel AC power transformer and disconnect the backup battery.
- 2. Remove and discard the module cover (Figure 3).
- 3. Insert a support standoff shown in Figure 4 (supplied with panel) into the panel circuit board...
- 4. Slide the module back-plate into the two top mounting clips located on the top-right side of t...
- 5. Push the lower-left corner of the module onto the support standoff (see detail in Figure 5).
- Connecting the Antennas to the Module
- Concord Panel Wiring
- Installing an Optional Cover Tamper Switch
- To install the tamper reed switch (Figure 7):
- 1. Slide the reed switch into the reed switch holder located on the module back-plate as shown in...
- 2. Insert the magnet into the nibs on the module cover. Remove the magnet clip from the module ba...
- 3. Connect the normally closed reed switch (in series with a 2.0K ohm EOL resistor) to the desire...
- To install the tamper reed switch (Figure 7):
- Setting the Unit Number
- Power Up and Bus Communication
- To power up the panel and receiver module:
- 1. Verify that all wiring at the panel, touchpad, and receiver is correct.
- 2. Connect the panel backup battery and plug in the panel AC power transformer.
- 3. Verify that the receiver module status LED is on.
- 4. If desired, enter panel program mode to verify unit number exists (see panel Installation Inst...
- Changing the Receiver Module Unit Number (software versions 1.0–1.6)
- To change the receiver module unit number:
- 1. Remove panel AC power transformer and backup battery.
- 2. Change the DIP switch setting on the module (see Figure 8). Remember, the setting must be diff...
- 3. Connect the panel backup battery and plug in the AC power transformer. The panel automatically...
- 4. The system may still indicate a bus failure if the panel learned a unit number that is no long...
- 5. Exit from program mode. The touchpad and all other bus devices should operate correctly and an...
- Replace Module Cover/Close Cabinet
- To power up the panel and receiver module:
- Programming
- Testing
- Troubleshooting
- Problem
- Action/Solution
- 1. Check for incorrect wiring connections.
- 2. Make sure the panel AC power transformer is plugged in and the backup battery is connected.
- 3. If the LED still remains off, replace the module.
- 1. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...
- 2. Check for incorrect wiring connections.
- 3. Check receiver antenna connections.
- 4. Check for receiver antenna proximity to metal obstructions such as ducting or AC wiring.
- 5. If the LED still doesn’t flash, replace the module.
- 1. Check that no bus devices are set to the same unit number.
- 2. Change the module unit number and re-initialize the panel/module by disconnecting and reconnec...
- 1. Make sure that the wireless zone capabilities of the module and panel have not been exceeded. ...
- 2. If the system still doesn’t respond, replace the module.
- Specifications
- Notices
1
ITI Part No. 60-764-01-95R
Installation Instructions
Document Number: 466-1565-01 Rev. A
June 2000
Product Summary
The SuperBus 2000 RF Receiver Module is a UL listed
device that adds or expands panel wireless zone capacity.
See the specific panel Installation Instructions for complete
UL requirements for the system you are installing.
The receiver is compatible with all ITI 319.5 MHz (crystal
and SAW) Learn Mode
™
wireless sensors and touchpads,
and can be mounted inside the panel cabinet or located up to
2,800 feet away from the panel (see Table 2). It receives
information from wireless sensors and touchpads then sends
the data to the panel via the SuperBus 2000 digital data bus.
Power for the module is provided by the panel.
Receivers are available in 16-zone (-16Z), 32-zone (-32Z),
or panel maximum (-MAX) capacities.
SuperBus 2000
vs.
SuperBus
SuperBus 2000 panels have the ability to auto-address mod-
ule unit numbers. When the panel is powered up, the panel
automatically reads the unique SuperBus 2000 device ID
number and assigns a unit number to the module. This elim-
inates manually setting DIP switches and the chance of
identical unit number conflicts.
SuperBus panels communicate with SuperBus 2000
modules but require the module unit number to first be set
manually using DIP switches.
The SuperBus 2000 RF Receiver Module features:
❑ Spatial diversity, which minimizes wireless signal nulls
or dead spots.
❑ Compatibility with all ITI 319.5 MHz (crystal or SAW)
Learn Mode ™ wireless sensors, touchpads, and sirens.
❑ Backward compatibility with SuperBus panels.
❑ 1,500 feet nominal, open air receiving range.
Figure 1 shows the receiver module components and Table
1 describes them.
Figure 1. RF Receiver Module Components
Table 1. Component Descriptions
Component Function
Antennas Provide communication with
wireless devices.
SuperBus 2000 Device
ID Number Label
Identifies unique module
SuperBus 2000 device ID
number (SuperBus 2000 panels).
Receiver Status LED On continuously when the
receiver is powered. Flashes
when an RF signal is received.
Unit Number DIP
Switches
Used for manually setting unit
numbers (SuperBus panels).
Terminal Strip Used for power and bus
connections to panel.
1065G03A.DSF
MOUNTING
HOLES (3)
CIRCUIT
BOARD
ANTENNA
TERMINAL BLOCKS (2)
ANTENNAS
STATUS
LED
TERMINAL
STRIP
UNIT
NUMBER
DIP SWITCHES
ID: XXXXXXXX
SUPERBUS 2000
DEVICE ID
NUMBER LABEL
MAGNET
CLIP
REED SWITCH
HOLDER
8543130A.DS4