User's Manual

ManualsBrandsUTC Fire & Security Americas ManualsElectronicsTRAC-LID BT SMART

Introduction

TheTRAC-Vault BT is an intelligent storage device that

holds multiple keys or access cards and completely

documents access and recent use.

These installation instructions are intended for the

TRAC-Vault BT Smart and TRAC-Vault BT devices. If you

choose an installation method other than the one described

in these instructions, Supra will not be responsible for

replacing the TRAC-Vault BT Smart or TRAC-Vault BT if it

is damaged or destroyed upon removal.

Hardware

Recommended Hardware:

• Four (4) HECO MMS-SS 10 x 100 screws

Required Equipment:

• Drill

• Drill bits

• Wrenches

• Pliers or vice grips

You can order an installation kit from Supra that contains all

the necessary hardware for installing the TRAC-Vault BT.

An interior cover plate is also available.

TRAC-Vault BT Smart Installation

Install the TRAC-Vault BT Smart and TRAC-Vault BT

in a location convenient for keyholders. To meet ADA

requirements, the unit must be installed 48 inches from

the ground to the center of the device.

Important:

— Only masonry installation is approved for LPS 1175

certication. Through-the-wall installation method was

not tested to LPS 1175: Issue 7 SR2.

— Use four HECO MMS-SS 10x100mm masonry screws

or equivalent screws to maintain the LPS1175 security

certication.

— Never install masonry screws into mortar.

— When mounting on a rendered wall, the maximum

distance between the back of the keysafe and the

masonry substrate must be 10 mm.

— Do not mount TRAC-Vault BT devices closer than 6” or

15cm to the corner of a masonry surface.

P/N10103266P1-01RevA•April2014

Figure 2. TRAC-Vault, side view

Figure 1. Mounting holes

Lock washer

Nut

TRAC-Vault

TRAC-Lid BT

Drain hole

Lid chain

attachment

Vault

chain bracket

Drain hole

Four mounting

holes for 5/16”

bolts

Tighten bolts in the

sequence indicated

by these numbers

Hole for tamper

switch wires

• Level or punch

• Pen or pencil

• Dremel tool or

hacksaw

TRACcess

TRAC-Vault BT Smart

●

Surface Mount

Installation Instructions

Summary of content (6 pages)

PAGE 1
® TRACcess TRAC-Vault BT Smart ● Surface Mount Installation Instructions Introduction Figure 1. Mounting holes TheTRAC-Vault BT is an intelligent storage device that holds multiple keys or access cards and completely documents access and recent use. These installation instructions are intended for the TRAC-Vault BT Smart and TRAC-Vault BT devices.
PAGE 2
— Make sure TRAC-Vault BT devices is mounted flush with masonry surface and the masonry screws are only installed directly into brick. Figure 3. Optional Tamper Switch — Minimize all gaps between back of TRAC-Vault BT devices and masonry surface. Tamper switch adjustment screw Rendered Wall Installation: 1. While holding the vault in the desired position on the wall, locate the four mounting holes away from mortar lines and the edge of the wall. 1 Normally open 2 Normally closed 3 Common 2.
PAGE 3
Through-the-Wall Installation: Retract the Blades: This method was not tested to LPS 1175: Issue 7 SR2. 1. Push the chrome button until the red LED blinks to turn on the TRAC-Lid. 1. Before drilling, verify there is no interference with any plumbing, electrical, fire or security systems, etc. 2. After choosing the location, level the template on the wall and mark the holes for drilling (see Figures 1 & 5). 3.
PAGE 4
® TRACcess TRAC-Vault BT Smart ● Montage en surface Instructions d’installation Introduction Le TRAC-Vault BT Smart y TRAC-Vault BT est un équipement de stockage intelligent contenant plusieurs clés ou cartes d'accès et capable de documenter intégralement les accès et utilisations récentes. Matériel Image 1.
PAGE 5
2 Installation sur mur avec revêtement : 1. Tout en maintenant le coffre dans la position qui convient sur le mur, placer les quatre trous de montage aussi loin que possible des lignes de mortier et du bord du mur. Image 3. Interrupteur d'autoprotection optionnel Vis d'ajustement de l'interrupteur d'autoprotection 2. À l'aide d'un marqueur, tracer l'emplacement des quatre trous de montage. (Se référer à l'image 1). 1 Normalement ouvert 3.
PAGE 6
3 3. Percer, à l'aide de la mèche qui convient au type de mur en question, des trous suffisamment grands pour la tige filetée 5/16. 4. Insérer une rondelle de blocage et un écrou sur trois des quatre tiges filetées. Sur la quatrième, installer une rondelle de blocage, le support de fixation de la chaîne puis l'écrou. Note : Il est important de bien aligner (à plat) l'écrou et le bout de la tige filetée. 5.