802.11 a/b/g/n + BT 4.2 module User Manual Model No.
1. Product Spec WiFi Features Description WLAN Standards IEEE 802.11 a/b/g/n Antenna Port Single Antenna 1Tx/1Rx, Printed Antenna for WiFi & Bluetooth 2.4GHz Band channel 1 ~ 11 Number of Sub Channels 5GHz band channel 36 ~ 165 Modulation DSSS, CCK, OFDM, BPSK, QPSK, 16QAM, 65QAM 1, 2, 5,5, 11 (Mbps) Supported data rates 6, 9, 12, 18, 24, 36, 48, 54 (Mbps) HT20_MCS0 (6.
2.
Bluetooth Execute Tera Term Program Set Serial Port to “com10” (depend on which com port of WM-BAN-MT-41 get in OS) Setup --> Serial Port --> Baud rate: 921600 --> OK Input command as below wifi_task bt_task btaddr (get module’s MAC address) MAC, ex:46:A3:FC:9D:E3:26 Another NB, user ubuntn USB start up Ubuntu system.
3. Regulatory Information Federal Communication Commission Interference Statement This module is certified pursuant to two Part 15 rules sections(15.407, 15.247). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed with 20 cm is maintained between the antenna and users in mobile or fixed applications. 2) The Antenna for Module (WM-BAN-MT-41) is Non-detachable and the maximum antenna gain allowed for use with this device is 0dBi@2.4GHz band & 3dBi@5GHz band. 3) The transmitter module may not be co-located with any other transmitter or antenna.
Industry Canada statement: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module. 2. the ISED compliance requirement of the end product, which integrates this module. 3. Appropriate measurements and if applicable additional equipment authorizations of the host device to be addressed by the integrator/manufacturer. 4. The separate approval is required for all other operating configurations, including portable configurations and different antenna configurations.
produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. Informations sur les modes de test et les exigences de test supplémentaires: Ce module est limité à l'intégration dans des hôtes pour une utilisation en intérieur uniquement. Ce module a été approuvé en configuration autonome. L'intégrateur OEM a limité les canaux d'opération dans le canal 1-11 pour la bande 2,4 GHz.
les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 10293A-WMBANMT41". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.