Setup Guide

ManualsBrandsUSI ManualsElectronics802.11a/b/g/n/ac + BT 4.1 Module

WM-BAC-BM-25 Setup Guide

cTX/RX & EMC for WiFi

1. The command shall be used in Linux OS.

2. Open terminal and enter the path (cd /usr/local/custom/EMC/Sheldon/BM25).

3. Enter “dmesg” and BM-25 is enabled while the information (mmc0: new high speed SDIO card

at address 0001) is shown.

4. Enter “modprobe cfg80211” and then enter “sh wifi_bringup.sh

fw_bm25_7.45.100.9_mfg_enc.bin bcm943457wlsagb-EMC-bm25.txt”.

5. Enter “cd Test_Script/” and then enter “tx”, “rx” or “cw”.

**The command to generate single tone signal is in “cw”, the command to generate continuous

TX signal is in “tx” and the command to generate continuous RX signal is in “rx”.

6. Example of the command for WiFi_TX

1) “sh tx_b_2g.sh <channel> <data rate> <power setting>” will generate 802.11b signal.

2) Change “tx_b_2g.sh” to other file name and then the signal with other modulation will be

generated.

7. Example of the command for WiFi_RX

1) “sh rx_b_2g.sh <channel> <data rate>” will generate 802.11b signal.

2) Change “rx_b_2g.sh” to other file name and then the signal with other modulation will be

generated.

8. Example of the command for single tone

1) “sh cw_2g.sh <channel>” will generate the single tone of 2.4GHz band.

2) “sh cw_5g.sh <channel>” will generate the single tone of 5GHz band

Summary of content (9 pages)

PAGE 1
WM-BAC-BM-25 Setup Guide cTX/RX & EMC for WiFi 1. The command shall be used in Linux OS. 2. Open terminal and enter the path (cd /usr/local/custom/EMC/Sheldon/BM25). 3. Enter “dmesg” and BM-25 is enabled while the information (mmc0: new high speed SDIO card at address 0001) is shown. 4. Enter “modprobe cfg80211” and then enter “sh wifi_bringup.sh fw_bm25_7.45.100.9_mfg_enc.bin bcm943457wlsagb-EMC-bm25.txt”. 5. Enter “cd Test_Script/” and then enter “tx”, “rx” or “cw”.
PAGE 2
cTX/RX & EMC for BT 1. 2. 3. 4. The command shall be used in Linux OS. Open terminal and enter the path (cd /usr/local/custom/EMC/Sheldon/BM25). Enter “dmesg” to check which USB port it is. Enter “sh bt_mfg.sh BCM4345C0_003.001.025.0111.0000_Generic_UART_37_4MHz_wlbga_ref_iLNA_iTR_eLG_BT4. 2_test_only.hcd ttyUSB0”. 5. TX test for BT2.0 for “T) TX Test” item 1) Set “001122334455” as MAC address. 2) 3) 4) 5) Set “1” as Hopping mode. Set the number as the channel you need.
PAGE 3
) Set “0” as Payload type 4) Set “0” as Timeout 9. LE RX test for BT4.0/BT4.1 for “Q) [LE] RX Test” item 1) Set the number as the channel you need. 2) Set “0” as Timeout 10. Single tone of BT2.0, BT4.0/BT4.1 for “C) Set TX Carrier Frequency ARM” item 1) Set “0” as Carrier 2) 3) 4) 5) Set the number as the channel you need. Set “0” as Mode Set “0” as Modulation type Set “0” as Power table index 11.
PAGE 4
Regulatory statements US This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 5
20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 6
mobile or fixed applications. 2) The Antenna for Module (WM-BAC-BM-25 ) is Non-detachable and the maximum antenna gain allowed for use with this device is 1.59 dBi@2.4GHz band & 2.23dBi@5GHz band. 3) The transmitter module may not be co-located with any other transmitter or antenna. 4) OEM integrators Must demonstrate SAR test and meet compliance before end-product with module (WM-BAC-BM-25) marketed in portable application.
PAGE 7
environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm entre le radiateur et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed and operated with greater than 20cm between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 8
ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 10293A-WMBACBM25”.
PAGE 9
(ii) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.