HOOK-REV3.
The HOOK-REV3.0 module complies with the following features and standards: Features Description WLAN Standards IEEE 802 11b/g/n Frequency Band 2.400 GHz – 2.484 GHz Number of Sub Channels CH1 to CH14 Modulation DSSS, CCK, OFDM, BPSK, QPSK, 16QAM, 64QAM Supported data rates 11b 1, 2, 5.5, 11 (Mbps) 11g 6,9,12, 18,24 ,36, 48, 54 (Mbps) 11n HT20 MCS0 (6.5Mbps) to MCS7 (65Mbps) Power supply for the HOOK-REV3.0 module will be provided as below: Symbol Parameter Min Typ.
User Guide WiFi User Mode 1. Power Supply set to 3.8V 2. Set up diagram as below: 3. Power supply turn on and insert SDIO cable to PC 4. Open terminal (ctrl+alt+T) and enter command “dmesg” to confirm if the device is recognized. 5. If your device is recognized and please enter the commands by step as following: 1) sudo su 2) cd .. 3) cd .. 4) cd usr/local/custom/EMC/Kelly/HOOK 5) ls 6. Enter command “sh list_fw.sh HOOK”.
7. Enter command “sh wifi_bringup.sh bcm43438-7.46.58.11.bin bcm943430wlselgs_27_4Mhz_20171226.txt” to enable user mode. * command rule is “sh wifi_bringup.sh + MFG/user mode FW name + NVram name” 8. Enter command “wl up” to bring up WiFi function.
9. You can enter command “ifconfig” or “iwconfig” to confirm if usi0 is shown on the available list. 10. Enter command “wl scan” and then enter command “wl scanresults”. It will show every SSID which you just scanned. And you will see a lot of SSID names, please choose one you want to connect.
11. If you want to connect to the AP and its SSID is dlink-A360-2.4GHz, please enter command “wl join dlink-A360-2.4GHz” to connect the AP.
12. Enter command “dhclient usi0” to have a fixed IP. And enter command “iwconfig” to confirm if you have already connected successfully.
13. Please enter command “ping 192.168.0.1” to confirm if the connection between the device and AP is ready. 14. Please enter command “iperf –c 192.168.0.11 –t 1000 –i 2”. And on the other NB, please enter “iperf –s “ to start throughput testing.
BT User Mode 1. Power supply set to 3.8V 2. Micro USB cable or UART cable are both available to control BT 3. Set up diagram as below: 4. Power supply turn on and insert cable to PC 5.
3) Enter command “hciattach -np /dev/ttyUSB0 any”
6.
7. Go back to T1 and enter ctrl+c, then enter command “hciattach -np /dev/ttyUSB0 any 460800” 8. On the left top corner：search your computer "bluetooth manager", after bluetooth manager window pops out, click “search”.
9. When the device you want to pair is shown on the list, then right click to perform “pair”.
10.
2) Enter command “ pactl list sinks short” to confirm all the device à Please remember the device you just paired
3) Enter command “ pacmd set-default-sink 1” to select your device, then enter command “pacmd stat” to confirm again if Default sink name us your device you just paired. 11. Copy your music file to Home directly. Please note the file format must be .
12. Go T3 and play music, please enter command “aplay test.
FCC ID: COFHOOKREV3 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This module is intended for OEM integrators under the following conditions: FCC: This module is certified pursuant to two Part 15 rules sections (15.247). Canada/ISED: This module is certified pursuant to RSS-247 rules sections. This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated, and must include 0.5 dB cable loss compensation. FCC, ISED Antenna Information Technology Frequency Band Antenna Type Model Number Gain (dBi) Wi-Fi 2400-2483.
Label of the end product: FCC: The host product must be labeled in a visible area with the following " Contains FCC ID: COFHOOKREV3". Canada/ISED: The final end product must be labeled in a visible area with the following: “Contains IC: 10293A-HOOKREV3”.
Taiwan/NCC 1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、 加大功率或變更原設計之特性及功能。 2.
Wireless Product Business Unit / Hardware Development Division Document No. Product No. Project Code Model No. Rev. HOOK_REV3.0 EVB PCB Specification of EV Board For HOOK_REV3.0 SOURCE ORGANIZATION : USI/WP//RD Kimi Chang Prepared by︰ Date : 2018-03-31 Checked by︰ Date : Approved by︰ Date : Concurrence︰ Date : 1.
Wireless Product Business Unit / Hardware Development Division Revision History Version No. Revised Date Revised by 1.0 2017/06/29 Kimi Chang Initial Release 1.1 2017/11/03 Kimi Chang Update layout 1.
Wireless Product Business Unit / Hardware Development Division 1. Scope: This PCB SPEC is for EV board of HOOK_REV3.0. This document define the PCB (Printed Circuit Board) manufacturing SPEC. Due to this product are applied in wireless communication field, so all the SPEC defined in this document should be followed strictly in order to control the line impedance and parasitic effects. Any changes or modification must have written agreement of USI’s engineer. 2. Gerber file : GB_HOOK_EVB_V30_20180328_Lyly.
Wireless Product Business Unit / Hardware Development Division 13. Impedance control is required for the following picture. Please adjust the trace red to fit 50 ohm. Please adjust the trace yellow to fit differential 90 ohm.
