DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377 - USA.
USB 7013 - 7014 Console mixers GENERAL SAFETY INSTRUCTIONS - Always read the user guide before using the equipment. Keep the user guide in a place where everyone can read it. Use the equipment indoors and not in humid environments. Never remove or insert a plug from or into a wall socket with wet hands. If the plug and/or cable and/or cable input of the equipment is damaged it must be repaired by a professional.
USB 7013 - 7014 Console mixers MONO INPUT CHANNELS 1. MIC INPUT The MIC input accepts XLR-type connectors and is designed to use a wide range of BALANCED or UNBALANCED signals; it has 48V Phantom power supply and it can connect high capacity microphones. Pin 1=Ground, Pin 2=signal+, Pin 3=signal2. LINE INPUT Accepts 3-pole 6.3 mm Jack. It uses this high impedance input for sources other than mics, such as keyboards, drum machines, synths, tape recorders or guitars.
USB 7013 - 7014 Console mixers MONO INPUT CHANNELS 9. AUX Used for monitoring the stage or playback room's return. 10. EFFECT Lets the signal sent to inside or outside effectors. 11.FX Can let the signal sent to inside or outside effectors. Can also be used for monitoring the stage or the return of recording. 12. SOLO The FADER allows balancing of the various source signals being mixed to the Master section.
USB 7013 - 7014 Console mixers STEREO INPUT CHANNELS 1.MONITOR OUT This jack is to be connected with the input jack of a monitor amplifier when using separate monitor amplifiers. 2/3. AUX 1 Each of these six AUX outputs have a master output level control. 4.L/R PIN JACK Used for connection of line level equipment. (Tape recorders etc.) 5.GAIN The GAIN control sets the input level to the channel, allowing to match to a wide range of line level sources. 6.
USB 7013 - 7014 Console mixers STEREO INPUT CHANNELS 9.BAL This control sets the amount of the channel signal feeding the Left and Right MIX buses, allowing you to move the source smoothly across the stereo image. When the control is turned fully right or left you are able to route the signal at unity gain to either left or right outputs individually. 10. SOLO When you want monitor echo sound and external effectors sound, you can adjust this control through the headphone. 11.
USB 7013 - 7014 Console mixers OUTPUT CHANNELS 1. BALANCE OUTPUT (MAIN L/R) These sockets send line level signals from the mixer to external devices (for example: EQ or a power amplifier). 2. MIX INSERT (6.3 mm Jack) This is a pre-fade break in the signal path which can be used to feed a dynamics or mastering device.The signal is sent from the tip of the jack plug and the return path comes back in on the ring of the jack plug. 3.
USB 7013 - 7014 Console mixers OUTPUT CHANNELS 9.PHONES This controls the level of the signal sent to your headphones 10.REPAT This is used for adjusting frequency of echo repeat. Since too much echo repeat may cause a howl. Please adjust frequency properly. 11.MONITOR CONTROL This controls the level of the signal sent to your monitoring system. 12.EFFECT This is used for adjusting the volume of echo sound when connecting sound to RETURN jack. 13.
USB 7013 - 7014 Console mixers SPECIFICATIONS Frequency response Mic/Line Input to any Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+/-1 dB 20Hz-20KHz T.H.D Mic Sensitivity +30dBu, +20dBu @ all Outputs . . . . . . . . . . . . . . . . . . . . . . . . .<0.008%@1KHz Noise Mic input E.I.N (maximum gain, measured 22Hz, unweighted) . . . . . . . . . . . . . . . . . . .-128 dBu Aux and Mix Outputs (8ch.routed. faders down, 22Hz,unweighted) . . . . . . . . . . . . . . . .
© US Blaster Europe BV DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377 - USA.
USB 7013 - 7014 Console mixers ALGEMENE VEILIGHEIDSVOORSCHRIFTEN - Lees altijd eerst de gebruiksaanwijzing voordat u een apparaat gaat gebruiken. Bewaar de handleiding zodat elke gebruiker hem eerst kan doorlezen. Apparaat binnenshuis en niet in vochtige ruimtes gebruiken. Verwijder of plaats een stekker nooit met natte handen resp. uit en in de wandkontakt doos. Indien zowel stekker en/of netsnoer als snoeringang-in-het-apparaat beschadigd zijn dient dit door een vakman hersteld te worden.
USB 7013 - 7014 Console mixers MONO INGANGSKANALEN 1. INGANG VAN DE MICROFOON (MIC) Aan de MIC ingang kan de connector van het XLR-type (zgn. canon) aangesloten worden. Deze ingang is voor het aansluiten van een breed scala van bronnen van GEBALANCEERDE OF NIET GEBALANCEERDE signalen aangepast en is met een voeding van 48 V Phantom power uitgerust waardoor ook microfoons met hoog vermogen aangesloten kunnen worden. Pin 1 = aarde, Pin 2 = signaal+, Pin 3 = signaal- 2.
USB 7013 - 7014 Console mixers MONO INGANGSKANALEN 9. AUX Voor monitoring van het retoursignaal uit de ruimte of uit het apparaat voor weergave. 10. EFFECT Maakt het overdragen van een signaal voor de verwerking door interne of externe effectoren mogelijk. 11. FX Maakt het overdragen van het signaal voor de verwerking door interne of externe effectoren mogelijk. Het kan ook voor de monitoring van het retoursignaal uit de ruimte of uit de bandrecorder gebruikt worden. 12.
USB 7013 - 7014 Console mixers STEREO INGANGSKANALEN 1. MONITOR OUT Deze stekkerbus dient voor aansluiting van de connector van de versterker voor uitluisteren, onder voorwaarde dat deze voor een separate versterker voor uitluisteren gebruikt wordt. 2/3. AUX 1 Elke van de zes stekkerbussen van AUX uitgangen is met een hoofdbediening voor het uitgangsniveau uitgerust. 4. CONNECTOR L/R Deze connector dient voor de aansluiting van een uitrusting die de lijnuitgang (line) gebruikt (bijv. bandrecorder e.d.). 5.
USB 7013 - 7014 Console mixers STEREO INGANGSKANALEN 9. BAL Met deze bediening wordt het volume van een signaal uit het betreffende kanaal ingesteld dat naar de rechter of linker bus van het mengpaneel wordt doorgegeven; hierdoor wordt een geleidelijke beweging van de signaalbron in het kader van stereofonisch spectrum mogelijk. Indien de knop in de positie helemaal links of helemaal rechts is gedraaid, kan het signaalniveau afzonderlijk gehoord worden en wel uit de rechter of de linker uitgang. 10.
USB 7013 - 7014 Console mixers UITGANGSKANALEN 1. GEBALANCEERDE UITGANG (MAIN L/R) Met behulp van deze stekkerbussen worden uitgangslijnsignalen overgedragen vanuit het mengpaneel naar een extern apparaat (bijvoorbeeld een equalizer of eindversterker). 2. MIX INSERT (6,3 mm jack) Maakt een ingreep in het spoor van het signaal pre-fader, voor het omleiden naar een dynamische processor of een ander mastering apparaat, mogelijk.
USB 7013 - 7014 Console mixers UITGANGSKANALEN 9. KOPTELEFOON (PHONES) Bedient het niveau van het signaal van overdracht naar de koptelefoon. 10. REPEAT Dit wordt voor het instellen van de frequentie van het herhalen van echo. Te hoge frequentie van het herhalen van echo kan een ongewenst geruis veroorzaken. Stel een juiste frequentie in. 11. BEDINING VAN MONITOREN (MONITOR CONTROL) Het dient voor het instellen van het signaalniveau overgedragen naar het monitoring systeem (uitluisteren). 12.
USB 7013 - 7014 Console mixers SPECIFICATIE Frequentieweergave Ingang Mic/Line naar een willekeurige uitgang +/-1 dB: . . . . . . . . . . . . . . . . . . (20 Hz - 20 kHz) THD (Harmonische vervorming) Bij de gevoeligheid Mic +30 dB, en +20 dB aan alle uitgangen: . . . . . . . . . . .<0,008% bij 1 KHz Geruis Ingang Mic (bij maximale gain, gemeten 22 Hz, ongebalanceerd geruis) . . . . . . . . . . . .
© US Blaster Europe BV DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377 - USA.
USB 7013 - 7014 Console mixers CONSIGNES GÉNÉRALES DE SÉCURITÉ - Toujours lire le manuel de l’utilisateur avant d’utiliser l’équipement. Conserver le manuel de l’utilisateur dans un endroit accessible à tous. Utiliser l’équipement à l’intérieur et pas dans des pièces humides. Ne jamais brancher ou débrancher une prise avec les mains mouillées. Si la prise et/ou le fil et/ou l’entrée du câble de l’équipement est endommagé, il doit être réparé par un professionnel.
USB 7013 - 7014 Console mixers CANAUX D’ENTRÉE MONO 1. ENTRÉE DU MICROPHONE(MIC) À l’entrée MIC est possible de raccorder un connecteur de type XLR. Cette entrée est adaptée au raccordement de nombreuses sources de signal SYMÉTRIQUE ou ASYMÉTRIQUE ; elle est équipée d’une alimentation fantôme de 48V, par conséquent, elle permet de brancher des microphones à puissance élevée. Pin 1 = mise à la terre, Pin 2 = signal+, Pin3 = signal2.
USB 7013 - 7014 Console mixers CANAUX D’ENTRÉE MONO 9. AUX Sert au contrôle du signal de retour de la pièce ou du lecteur. 10. EFFECT Permet l’envoi de signal vers l’organe effecteur externe pour traitement. 11. FX Permet l’envoi de signal vers l’organe effecteur interne ou externe pour traitement. Peut également être utilisé pour le contrôle du signal de retour de la pièce ou de l’enregistreur. 12.
USB 7013 - 7014 Console mixers CANAUX D’ENTRÉE STÉRÉO 1. MONITOR OUT Cette fiche sert au raccordement du connecteur de l’amplificateur de contrôle à condition d’utiliser un amplificateur de contrôle séparé. 2/3. AUX 1 Chacune des six fiches de sorties AUX est équipée d’une commande principale du niveau de sortie. 4. CONNECTEUR L/R Sert au raccordement d’un dispositif utilisant une sortie de ligne (magnétophone, etc). 5.
USB 7013 - 7014 Console mixers STEREO INGANGSKANALEN 9. BAL Cette commande règle la quantité de signal du canal correspondant transmis vers le bus droit ou gauche du pupitre de mixage ; ceci permet un mouvement continu de la source de signal dans le cadre du spectre stéréophonique. La rotation complète du bouton à droite ou à gauche permet de diriger individuellement le signal de la sortie droite ou gauche. 10.
USB 7013 - 7014 Console mixers CANAUX DE SORTIE 1. SORTIE ASYMÉTRIQUE (MAIN L/R) Ces fiches aident à envoyer les signaux de ligne de sortie depuis le pupitre de mixage vers le dispositif externe (égaliseur ou amplificateur de puissance, par exemple). 2. MIX INSERT (6.3 mm jack) Permet d’intervenir au niveau du chemin du signal par l’intermédiaire du prééquilibreur en vue de son reroutage vers un processeur dynamique ou un dispositif de maîtrise.
USB 7013 - 7014 Console mixers CANAUX DE SORTIE 9. ÉCOUTEURS (PHONES) Commande le niveau de signal envoyé vers les écouteurs. 10. REPEAT S’utilise pour le réglage de la fréquence de répétition de l’écho. Une fréquence de répétition de l’écho trop élevée peut engendrer un bruit indésirable. Réglez correctement la fréquence. 11. COMMANDE DES MONITEURS (MONITOR CONTROL) Sert au réglage du niveau de signal envoyé vers le système de surveillance. 12.
USB 7013 - 7014 Console mixers CARACTÉRISTIQUES Réponse en fréquence Entrée Mic/Line dans n’importe quelle sortie +/-1 dB: . . . . . . . . . . . . . . . . . . . . . . .20Hz-20KHz THD (Distorsion harmonique) Lors de la sensibilité d’entrée Mic +30dB et +20dB sur toutes les sorties: . . . . . .<0.008% à 1KHz Bruit Entrée Mic (gain maximal, mesuré 22Hz, puissance de bruit non pondérée) . . . . . . . . . .
© US Blaster Europe BV DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377 - USA.
USB 7013 - 7014 Console mixers ALLGEMEINE SICHERHEITSHINWEISE - Lesen Sie stets das Benutzerhandbuch durch, bevor Sie das Gerät verwenden. Bewahren Sie das Benutzerhandbuch an einem Ort auf, wo es für alle zugänglich ist. Verwenden Sie das Gerät nicht im Freien und nicht in feuchten Räumen. Stecken Sie den Netzstecker nie mit nassen Händen in die Steckdose oder ziehen ihn heraus.
USB 7013 - 7014 Console mixers EINGANGSMONKANÄLE 1. MIKROPHONEINGANG (MIC) in den MIC-Eingang ist möglich den Verbindungsstecker Typ XLR (s.g. canon) einzuschließen und dieser Eingang ist für den Anschluss von breiter Quellenskala des SYMMETRISCHEN oder UNSYMMETRISCHEN Signals angepasst; er ist mit der Speisung 48V Phantom power ausgestattet und darum ist möglich auch die Mikrophone mit hoher Leistung anzuschließen. Pin 1=Erdung, Pin 2=Signal+, Pin3=Signal2.
USB 7013 - 7014 Console mixers EINGANGS-MONOKANÄLE 9. AUX Dient zur Verfolgung des Rückgabesignals aus dem Raum oder dem Bandspieler. 10. EFFECT Ermöglicht die Absendung des Signals zur Bearbeitung durch den internen oder externen Effektor. 11.FX Ermöglicht die Signalabsendung zur Bearbeitung durch den internen oder externen Effektor. Es kann auch zur Verfolgung des Rückgabesignals aus dem Raum oder aus dem Bandspieler ausgenutzt werden. 12.
USB 7013 - 7014 Console mixers EINGANGSSTEREOKANÄLE 1.MONITOR OUT Diese Steckbuchse dient zum Anschluss des Verbindungssteckers vom Abhörverstärker unter der Voraussetzung, dass der separate Abhörverstärker benutzt wird. 2/3. AUX 1 Jede der sechs Steckbuchsen der AUX – Ausgängen ist mit der Hauptbedienung des Ausgangspegels ausgestattet. 4. VERBINDUNGSSTECKER L/R Dient zum Anschluss der Einrichtung, die den Linienausgang (line) benutzt (Kassettenrecorder u.ä.) 5.
USB 7013 - 7014 Console mixers EINGANGSSTEREOKANÄLE 9.BAL Diese Bedienung stellt den Signalumfang aus den zuständigen Kanal ein, der in rechten oder linken Bus des Mischpultes übergeben wird; dadurch ist laufende Bewegung der Signalquelle im Rahmen des stereophonischen Spektrums ermöglicht. Ist die Taste völlig nach rechts oder nach links gedreht, ist die Verfolgung des Signalpegels einzeln ermöglicht und das entweder des rechten oder linken Ausganges. 10.
USB 7013 - 7014 Console mixers AUGANGSKANÄLE 1. SYMMETRISCHER AUSGANG (MAIN L/R) Anhand dieser Steckbuchsen sind die Ausgangsliniensignale aus dem Mischpult in die externe Einrichtung abgesendet (z.B. in Equalizer oder Leistungsverstärker). 2. MIX INSERT (6.3 mm Jack) Ermöglicht den Eingriff in die Signalspur vor dem fader zwecks seiner Umlenkung in den dynamischen Prozessor oder in andere mastering Einrichtung.
USB 7013 - 7014 Console mixers AUSGANGSKANÄLE 9. KOPFHÖRER (PHONES) Bedient den Pegel des in die Kopfhörer abgesendeten Signals. 10. REPEAT Wird zur Frequenzeinstellung der Echowiederholung benutzt. Zu hohe Frequenz der Echowiederholung kann das unerwünschte Gebraus verursachen. Stellen Sie die Frequenz richtig ein. 11. BEDIENUNG DER MONITOREN (MONITOR CONTROL) Dient zur Pegeleinstellung des in das Überwachungssystem abgesendeten Signals (Abhören). 12.
USB 7013 - 7014 Console mixers Nebensprechen Kanalabdämpfung . . . . . . . . . . . . . . . . . . . . . . .<90dB bei 20Hz-10kHz, <80dB bei 10kHz-20kHz Cut-Off vom fader (zust. Fader auf OdB) . . . . . .<90dB bei 20Hz-10kHz, <80dB bei 10kHz-20kHz Isolation der Signalumlenkung . . . . . . . . . . . . .<90dB bei 20Hz-10kHz, <80dB bei 10kHz-20kHz Impedanz des Ein- und Ausgangs Mikrophoneingang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
© US Blaster Europe BV DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377 - USA.
USB 7013 - 7014 Console mixers ISTRUZIONI GENERALI DI SICUREZZA - Leggere sempre la Guida dellíutente prima di utilizzare questa attrezzatura. Conservare la Guida dellíutente in un luogo di facile accesso, ove tutti possano consultarla. Utilizzare questa attrezzatura allíinterno e in locali che non presentino umidit‡. Non rimuovere, nÈ inserire mai la spina di alimentazione in una presa a muro con mani umide.
USB 7013 - 7014 Console mixers MONO CANALI D´ INGRESSO 1. Nell´ingresso MIC si puo´ collegare il connettore tipo XLR (cosidetto canon), e tale ingresso é adattato per il collegamento di una vasta scala di sorgenti del segnale SIMMETRICO O ASIMMETRICO., é dotato di alimentazione 48 V Phantom power, e pertanto é possibile collegare anche i microfoni di alta potenza. Pin 1 = messa a terra, Pin 2 = segnale +, Pin 3 = segnale- 2. INGRESSO DI LINEA (LINE) Serve per il collegamento del jack tripolare da 6.
USB 7013 - 7014 Console mixers MONO CANALI D´ INGRESSO 9. AUX Serve per il monitoraggio del segnale di ritorno dal locale o dal lettore. 10 EFFECT Permette la trasmissione del segnale per la riduzione tramite l´ effettore interno o esterno. 11. FX Permette la trasmissione del segnale per la riduzione tramite l´ effettore interno o esterno. Puo´essere altresí utilizzato per il monitoraggio del segnale di ritorno dal locale o dal registratore. 12.
USB 7013 - 7014 Console mixers STEREO CANALI D´ INGRESSO 1. MONITOR OUT Tale presa di ingresso serve per il collegamento del connettore dell´amplificatore per l´ ascolto, purché venga utilizzato l´amplificatore per l´ascolto separato. 2/3. AUX 1 Ciascuna delle sei prese d´ ingresso AUX é dotata di comando principale del livello d´uscita. 4. CONNETTORE L/R Serve per il collegamento del dispositivo, che utilizza l´uscita di linea (line), (registratore a cassette etcc.) 5.
USB 7013 - 7014 Console mixers STEREO CANALI D´ INGRESSO 9. BAL Tale comando regola il volume del segnale dal rispettivo canale, che viene trasmesso nel bus destro o sinistro del pannello di missaggio., in tal modo si permette la circolazione continua della sorgente di segnale nell´ ambito dello spettro stereofonico. Se il pulstante é completamente girato verso destra o sinistra, si puo´monitorare singolarmente il livello del segnale, sia quello dell´uscita destra che sinistra. 10.
USB 7013 - 7014 Console mixers CANALI D´ USCITA 1. USCITA SIMMETRICA (MAIN L/R) Attraverso tali prese di ingresso vengono trasmessi i segnali di linea d´uscita dal pannello di missaggio nel dispositivo esterno (per es. equalizzatore o amplificatore di potenza). 2. MIX INSERT (6.3 mm jack) Pemtette l´intervento nella pista del segnale pre-fader al fine del cambio della sua direzione nel processore dinamico o altro dispositivo mastering.
USB 7013 - 7014 Console mixers CANALI D´ USCITA 9. CUFFIE (PHONES) Regola il livello del segnale trasmesso nelle cuffie. 10. REPEAT Si utilizza per la regolazione della frequenza del raddoppio dell´eco. La frequenza troppa alta del raddoppio dell´eco puo´ causare brontolio indesiderato. Regolate esattamente la frequenza. 11. REGOLAZIONE MONITOR Serve per la regolazione del livello del segnale trasmesso nel sistema di monitoraggio (ascolto). 12.
USB 7013 - 7014 Console mixers SPECIFCAZIONI Risposta di frequenza L´ingresso Mic /Line in qualsiasi uscita . . . . . . . . . . . . . . . . . . . . . . . . . .+/-1 dB: 20 Hz -20 KHz THD (distorsione armonica) Con la sensibilitá dell´ingresso Mic + 30 dB, e +20 dB in tutte le uscite: . . .< 0.008% con 1 KHz Rumore Uscita Mic (con massimo gain, misurato 22 Hz, rumore disarmonico) . . . . . . . . . . . . . .– 128 dB Uscite Aux e Mix (monitorati 8 canali, fader abbassati con 22 Hz, rumore disarmonico) . .
© US Blaster Europe BV DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377 - USA.
USB 7013 - 7014 Console mixers INSTRUCCIONES GENERALES DE SEGURIDAD - Lea siempre la Guía de usuario antes de utilizar el equipo. Mantenga la Guía de usuario en un lugar donde todos puedan leerla. Utilice el equipo en interiores y no en estancias húmedas. Nunca quite ni conecte un enchufe de pared con las manos mojadas. Si el enchufe y/o cable y/o entrada del equipo estuviese dañado, deberá ser reparado por un profesional.
USB 7013 - 7014 Console mixers CANALES DE ENTRADA MONO 1. ENTRADA DE MICROFONO (MIC) En la entrada MIC se puede conectar un conector tipo XLR (el llamado canon) estando esta entrada adaptada para la conexión de una amplia gama de fuentes de señal BALANCEADA Y NO BALANCEADA, esta provista de una alimentación de 48V Phantom power y por lo tanto se pueden conectar también micrófonos de alta potencia. Pin 1=tierra, Pin 2=señal+, Pin3=señal2.
USB 7013 - 7014 Console mixers CANALES DE ENTRADA MONO 9. AUX Sirve para el monitoreo de la señal de retorno de la habitación o del reproductor. 10. EFFECT Hace posible el envío de señal para el procesamiento del efector interno o externo. 11.FX Hace posible el envio de señal para ser procesada por el efector interno o externo. Al miso tiempo puede aprovecharse para el monitoreo de la señal de retorno de la habitación o de la grabadora. 12.
USB 7013 - 7014 Console mixers CANALES DE ENTRADA ESTEREO 1.MONITOR OUT Este enchufe sirve para la conexióon del conector del amplificador de monitoreo en caso de que se este usando un amplificador separado de monitoreo. 2/3. AUX 1 Cada uno de los seis enchufes AUX de salidas esta equipado de un control principal de nivel. 4. CONECTOR L/R Sirve para la conexión de un equipo que use la salida de línea (line) (grabadora de casetes, etc). 5.
USB 7013 - 7014 Console mixers CANALES DE ENTRADA ESTEREO 9.BAL Este control ajusta el volumen de señal del canal correspondiente el cual es entregado en la barra colectora izquierda o derecha de la consola de mezcla, de esta manera se posibilita el movimiento continuo de la fuente de señal dentro del marco del espectro estereofónico.
USB 7013 - 7014 Console mixers CANALES DE SALIDA 1. SALIDA BALANCEADA (MAIN L/R) Mediante estos enchufes se envían las señales de línea de salida de la consola de mezcla al equipo externo (por ejemplo el ecualizador o el amplificador de potencia). 2. MIX INSERT (6.3 mm jack) Posibilita la intervención en la pista de la señal pre-atenuador con el objetivo de desvío al procesador dinámico u otro equipo de mastering.
USB 7013 - 7014 Console mixers CANALES DE SALIDA 9. AURICULARES (PHONES) Controla el nivel de señal enviada a los auriculares. 10. REPEAT Se usa para ajustar la frecuencia de repetición de eco. Una frecuencia demasiado alta de eco puede causar un ruido indeseado. Ajuste correctamente la frecuencia. 11. CONTROL DE MONITORES (MONITOR CONTROL) Sirve para ajustar el nivel de señal enviada al sistema de monitoreo. 12.
USB 7013 - 7014 Console mixers ESPECIFICACIONES Respuesta de frecuencia Entrada Mic/Line en cualquier salida +/-1 dB: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Hz-20KHz THD (Distorsión harmónica) Con una sensibilidad de salida Mic +30dB, y +20dB en todas las salidas: . . . . .<0.008% pfii 1KHz Ruido Entrada Mic (con una ganancia máxima, medido 22Hz, ruido no balanceado) . . . . . . . . .
© US Blaster Europe BV DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377 - USA.