Mod. 1086 DS1086-003A LBT20871 SCLAK UNIT RELÈ BLUETOOTH (CON ADATTATORE 2VOICE PER SCLAK UNIT) BLUETOOTH SCLAK UNIT RELAY (WITH SCLAK UNIT 2VOICE VOLTAGE ADAPTER) Sch./Ref.1086/11 LIBRETTO INSTALLAZIONE INSTALLATION HANDBOOK FCC. ID.
ITALIANO 1. DESCRIZIONE GENERALE Lo SCLAK Unit relè Bluetooth Sch. 1086/11 permette di trasformare qualunque serratura elettrica o sistema di automazione, in un sistema integrato di controllo accessi gestito da smartphone tramite tecnologia Bluetooth 4.0. Il dispositivo è compatibile con tutte le serrature elettriche, elettromagnetiche, elettro meccaniche e non richiede nessuna connessione a Internet per funzionare.
4. DESCRIZIONE DEL LED DI STATO E DEI FILI PRESENTI NEL CAVO PER LA CONNESSIONE ALL’IMPIANTO Led di stato Colore del led Spento Verde lampeggiante Verde fisso Spento per (N)* secondi Descrizione Dispositivo non alimentato Dispositivo alimentato e non configurato Dispositivo alimentato e configurato Attuazione comando serratura (*) Il tempo di spegnimento del led di stato è uguale al tempo di apertura porta impostato in fase di configurazione. Fili presenti nel cavo Nero Rosso Giallo / Verde 5.
• • Sulla postazione di chiamata rimuovere le testate del telaio utilizzando un cacciavite piatto e successivamente ribaltare il telaio. Posizionare il dispositivo SCLAK Unit relè Bluetooth Sch. 1086/11 all’interno della scatola ad incasso. ATTENZIONE! Portata massima del segnale all’aria aperta: 15 m. Pareti, ostacoli e contenitori metallici riducono la portata. • Effettuare i collegamenti in base alla tipologia di serratura. Fare riferimento al capitolo “Schemi di collegamento”.
I cavi impiegati devono rispondere alla norma IEC 60332-1-2 se di sezione 0,5 mm² o superiore, oppure alla norma IEC 60332-2-2 se di sezione inferiore a 0,5 mm². Dopo aver effettuato il collegamento il led di stato inizierà a lampeggiare per indicare che il dispositivo è alimentato ed è in attesa della configurazione. • Chiudere il telaio della pulsantiera e avvitare le viti di chiusura. 5.2.
Jumper JP3 e JP4 La posizione dei jumper JP3 e JP4 permette di selezionare la tipologia di tensione di alimentazione: • Sistema 2 fili 2Voice (48V ) • Con alimentatore locale da 12 ÷ 24 V (con queste alimentazioni deve essere utilizzato un cavo di lunghezza inferiore a 3m e alimentare il dispositivo con una potenza inferiore ai 15 watt) Posizione aperta (Default) Sistema 2 fili 2Voice 6.
. CARATTERISTICHE TECNICHE Tensione di alimentazione:............................................................................................. 48 V o 12 ÷ 24 V Potenza massima:....................................................................... Max 0,4W @ 48 V o Max 0,3W @ 24 V Uscita relé (fili bianco e marrone):................................................................................................ 1A @ 24 V Frequenza:......................................................................
ENGLISH 1. GENERAL DESCRIPTION The SCLAK Unit Bluetooth Relay Ref. 1086/11 makes it possible to transform any electric lock or automation system into an integrated access control system managed by smartphone using Bluetooth 4.0 technology. The device is compatible with all electric, electromagnetic, electro mechanical locks and does not require any internet connection to operate. The SCLAK Unit Bluetooth relay works with all smartphones running IOS 8 or higher or Android 4.3 or higher. 2. • • • 3.
4. DESCRIPTION OF THE STATUS AND LED THE WIRES IN THE CABLE FOR CONNECTION TO THE SYSTEM Status led LED colour Off Green flash Green fixed Off for (N)* seconds Description Device not powered Device powered and not configured Device powered and configured Actuation lock command (*) The switch-off time of the status LED is the same as the door opening time set in the configuration phase. Wires in the cable Black Red Yellow / Green 5.
• At the call station, remove the frame heads using a flat screwdriver and then turn the frame over. • Position the SCLAK Unit Bluetooth relay Ref. 1086/11 inside the flush-mounted box. ATTENTION! Maximum signal range in open air: 15 m. Walls, obstacles and metal containers reduce the range. • 10 Make the connections to the terminal board according to the type of lock. Refer to the chapter “Wiring diagram”.
Wires with cross-section area of 0.5 mm2 or larger must comply with IEC 60332-1-2; wires with cross section area smaller than 0.5 mm2 must comply with IEC 60332-2-2. After making the connection, the status LED will start flashing to indicate that the device is powered and is awaiting configuration. • Close the panel frame and tighten the closing screws. 5.2.
JP3 and JP4 Jumper The position of the jumpers JP3 and JP4 allow you to select the type of power supply: • 2-wire 2Voice system (48V ) • With local power supply from 12 ÷ 24 V (with these power supplies a cable shorter than 3m must be used and power the device with less than 15 watts of power) Open position (Default) 2-wire 2Voice system 6.
7. TECHNICAL FEATURES Supply voltage:.............................................................................................................. 48 V or 12 ÷ 24 V Maximum power:....................................................................... Max 0,4W @ 48 V or Max 0,3W @ 24 V Relay output (white and brown wires ):....................................................................................... 1 A @ 24 V Frequency :...........................................................................
9. SCHEMI DI COLLEGAMENTO / WIRING DIAGRAMS Collegamento di un dispositivo SCLAK Unit relè Bluetooth Sch. 1086/11 a una serratura elettrica standard o a una serratura elettromeccanica Connecting a SCLAK Unit Bluetooth Relay device Ref.
ITALIANO DIRETTIVA 2012/19/UE DEL PARLAMENTO EUROPEO E DEL CONSIGLIO del 4 luglio 2012 sui rifiuti di apparecchiature elettriche ed elettroniche (RAEE) Il simbolo del cassonetto barrato riportato sull’apparecchiatura o sulla sua confezione indica che il prodotto alla fine della propria vita utile deve essere raccolto separatamente dagli altri rifiuti.
DS1086-003A URMET S.p.A. 10154 TORINO (ITALY) VIA BOLOGNA 188/C Telef. +39 011.24.00.000 (RIC. AUT.) Fax +39 011.24.00.300 - 323 LBT20871 Area tecnica servizio clienti +39 011.23.39.810 http://www.urmet.com e-mail: info@sclak.