CORAL 36 OUTDOOR KITCHEN Specifications Installation Manual Care & Maintenance Equipment Compatibility Questions? Watch our installation videos on our YouTube channel or call Urban Bonfire for assistance: 1 (866) 898-5354
SUMMARY Specifications ....................................................... 3 Installation Manual ............................................... 6 Care & Maintenance ............................................. 14 Equipment Compatibility ......................................
CORAL 36 Specifications 1 2 Dimensions 4 3 1 Gas and Electrical Conduits Access Points *Length 135” *Depth 29 3/4” Height 36 1/2 ± 1” Gas and electric lines can easily be run in and out of the kitchen using the removable access panels located in the bottom and back of each cabinet. To run lines from cabinet to cabinet, use the circular conduit holes located at the top and bottom of each side. *Includes countertop nosing.
Tools Required Robertson #2 screwdriver and/or drill bit Level Phillips #2 head screwdriver and/or drill bit Clear Silicone Metal Hacksaw 3/8 Wrench Wood Shim Items Provided #8 screws Nuts 2” 8-32 Bolts Leg wrench 3” 8-32 Bolts (for 24” cabinet only) Toe kick clips Watch our installation videos on our YouTube channel or contact support@urbanbonfire.com ou 1 (866) 898-5354.
Installation Protocol 1. Measure out installation area and mark kitchen location. 2. Remove all internal components and place cabinets upside down on a protected surface. 3. Locate boxes containing cabinet legs and toe kicks. 4. Attach legs to cabinets by screwing on clockwise. 5. Using #8 screws, install side panel sliding toe kicks to applicable end-cabinets. Note: Do not overtighten. Keep tape on toe kick (see Fig. 1). 6. Using #8 screws, install back panel sliding toe kicks.
7. Place cabinets right side up so that they are standing on their legs. 8. Align cabinets into the kitchen location and attach them together using #8 screws in the front (see Fig. 2) and 2” long 8-32 bolts in the back (see Fig. 3). For 24” cabinet, use the 3” long 8-32 bolts provided. Note: Cabinets without finished back panels are to be attached through the back section of the cabinet (see Fig. 3). Cabinets with finished back panels are to be attached through the holes on the inside of the cabinet.
Fig. 3 - Connecting Cabinets BACKS Back of cabinets can be fastened together either from within the cabinet cavity (when back panels are present) or from the rear cabinet frame (when no back panels are present pictured). Use 2 bolts and nuts (supplied) and tighten. For 24” cabinet, use the 3” long 8-32 bolts provided. bolt nut Watch our installation videos on our YouTube channel or contact support@urbanbonfire.com ou 1 (866) 898-5354.
9. Install side trim to the grill base cabinet and side burner cabinets using #8 screws (see Fig. 4). Fig. 4- Installing the Side Trims The side trims fill the space around your equipment to provide a consistent finished look. Fasten the side trims, on both sides of the cabinet. Watch our installation videos on our YouTube channel or contact support@urbanbonfire.com ou 1 (866) 898-5354.
10. Level cabinets, using the adjustable legs, ensuring all legs are sitting solidly on the ground Use the leg wrench if needed for legs on the back of the kitchen. Note: Allow a small, consistent, slope for proper countertop drainage. 11. Installation must be done in accordance with included Dekton® Installation Guidelines. (see p.13) 12. Install the toe kick clips to the front toe kicks (see Fig.5). Fig. 5 - Installing the Toe Kick Clip Install the clip by sliding it to the bracket. 13.
14. Measure corner toe kick height and cut to size with hacksaw. Attach to the front and side toe kicks (see Fig. 7). 15. Remove tape from back and side toe kicks, allowing front plates to slide down to meet the ground. Adjust the legs if necessary to allow toe kicks to meet the ground. 16. Install interior components in the cabinets (waste and recycling insert, shelves, etc...) 17. Adjust the doors as necessary using hinges to maintain a consistent reveal. Fig.
Universal Track System Every Urban Bonfire utility cabinet is equipped with our universal track system. Numerous accessory options are available to maximize efficiency, functionality and usage of the cabinet. Moving the Bracket Along the Universal Track System 2. Pull the front of the bracket inwards to free the mounting screw from the vertical keyhole. 1. Push upwards on the front of the bracket until the mounting screw lines up with the wide portion of the keyhole. 3.
Adding END Finish Panels End finish panels are fastened from inside the cabinet with 2, #8 screws in the back and at least 3, #8 screws in the front (supplied). Ensure self leveling toe kick assembly is attached prior to installation. Adding BACK Finish Panels Back finish panels are fastened from inside the cabinet with 4, #8 screws (supplied). Ensure self leveling toe kick assembly is attached prior to installation. Watch our installation videos on our YouTube channel or contact support@urbanbonfire.
DEKTON® ULTRACOMPACT SURFACES COUNTERTOP INSTALLATION All cabinets and trim kits should be connected with screws and bolts provided in the kitchen installation package Inspect the package prior to opening to ensure it has not been damaged during transportation. Countertops must be transported and installed by two people. Apply clear silicone to attach the countertop Check the level of the entire installation Adjust the level using the leveling legs Installation Guidelines 1.
URBAN BONFIRE TM CABINETS MAINTENANCE GUIDE To prolong the life of your Urban Bonfire cabinetry and to remain satisfied with the product, please be sure to follow the below instructions: 1. Use the proper tools when cleaning your cabinets. Soft cloths are recommended. 2. Use alkaline, alkaline-chlorinated, or non-chloride cleaners. 3. Wipe off cleaning agents and standing water promptly. Prolonged contact will cause eventual problems. 4.
DEKTON® ULTRACOMPACT SURFACES CLEANING AND MAINTENANCE Normal Maintenance Due to its practically zero porosity, the ultra-compact Dekton® surface is highly resistant to staining in day-to-day use and from chemical products, making it ideal for use as a kitchen worktop and as a surface for other kinds of work, both inside and out. For general cleaning, Cosentino recommends the use of neutral soap and water with a sponge or scouring pad.
DEKTON® ULTRACOMPACT SURFACES CLEANING AND MAINTENANCE Prevention of Knocks Although Dekton® is an extremely resistant surface, knocks should be avoided in areas which are more exposed (corners, edges, bevels etc.). Performance in Contact with Hot Objects Recipients such as frying pans, saucepans, casseroles and coffee makers etc. can be placed directly on the work surface after use. Electrical apparatuses which give off heat can also be placed on the unprotected surface.
URBAN BONFIRE TM CORAL 36 EQUIPMENT COMPATIBILITY 36” Grill (ALXE-36) 36” Grill (G_BR36-NG /-LP) 34” Grill (BLZ-3PRO-LP/NG) 36” Grill (C2C36/C1S36/ C2SL36) 36” Grill (BH1-36R) 36” Grill (E__36-NG /-LP) 36” Grill (LF36ATR, L36ATR, L36TR, L36R-3) 36” Grill (L600, L600R, L600PS, L600PSR) 36” Grill (TEBQ36___) 36” Grill (OG36) 17