Network Bullet Cameras Quick Guide Manual Version: V1.
Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. Copyright Copyright 2015 Zhejiang Uniview Technologies Co., Ltd. All rights reserved. No part of this manual may be copied, reproduced, translated, or distributed in any form or by any means without prior consent in writing from our company. Trademark Acknowledgement and other Uniview’s trademarks and logos are the property of Zhejiang Uniview Technologies Co., Ltd.
Disclaimer The default password is used for your first login. To ensure account security, please change the password after your first login. You are recommended to set a strong password (no less than eight characters). To the maximum extent permitted by applicable law, the product described, with its hardware, software, firmware and documents, is provided on an "as is" basis.
change without prior notice. Update will be added to the new version of this manual. Use of this manual and product and the subsequent result shall be entirely on your own responsibility.
for any consequences resulting from illegal operations of the device. The illustrations in this manual are for reference only and may vary depending on the version or model. As a result, some of the examples and functions featured may differ from those displayed on your monitor. This manual is a guide for multiple product models and so it is not intended for any specific product.
proper storage, use and disposal of this product, national laws and regulations must be observed. Safety and Compliance Information Safety Symbols The symbols in the following table may be found on installation-related equipment. Be aware of the situations indicated and take necessary safety precautions during equipment installation and maintenance. Symbol Description Generic alarm symbol: To suggest a general safety concern. ESD protection symbol: To suggest electrostatic-sensitive equipment.
indicated by the symbols to avoid hazardous situations and use the product properly. Symbol Description WARNING! Indicates a hazardous situation which, if not avoided, could result in bodily injury or death. CAUTION! Indicates a situation which, if not avoided, could result in damage, data loss or malfunction to product. NOTE! Indicates useful or supplemental information about the use of product.
Installation This device is a class A product and may cause radio interference. Take measures if necessary. Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensor from dirt.
The sensor may be burned out by a laser beam, so when any laser equipment is being used, make sure that the surface of the sensor not be exposed to the laser beam. While shipping, the camera should be packed in its original packing. Maintenance If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a rubber dust blowing ball.
Do not use organic solvents, such as benzene or ethanol when cleaning the front glass surface. Never look at the transmit laser while the power is on. Never look directly at the fiber ports and the fiber cable ends when they are powered on. Use of controls or adjustments to the performance or procedures other than those specified herein may result in hazardous laser emissions.
Regulatory Compliance FCC Part 15 This equipment has been tested and found to comply with the limits for digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. LVD/EMC Directive This product complies with the European Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC.
WEEE Directive–2002/96/EC The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner.
Contents 1 Packing List ..................................................... 1 2 Appearance..................................................... 2 Dimensions and Appearance .......................................................... 2 Cable Connection ............................................................................ 2 3 Mount Your Camera ........................................ 3 Wall Mount .....................................................................................
Install the ActiveX..........................................................................
1 Packing List No. Item Quantity 1 Camera 1 2 User document 1 3 Accessory pack 1 Contact your local dealer if the package is damaged or incomplete.
2 Appearance Dimensions and Appearance 1 2 39mm (1.54") Φ4.5mm (0.
No. Description No. RESET button Power interface Description Earth terminal Network interface For specifications, see the latest product datasheets. Press and hold the RESET button for at least 15 seconds to restore factory default settings. Perform this operation within 10 minutes after the device is powered on or the reset will fail otherwise. 3 Mount Your Camera Wall Mount You can adopt wall mount or ceiling mount and purchase hardware accessories by yourself.
following part takes wall mount as an example. Ceiling mount is similar to wall mount and therefore is omitted here. 1 Locate the positions of the holes. 2 Drill holes on the wall. 1 Use a Ø 6-6.5mm drill bit. 1 Paste installation positioning stickers on the wall and align the cross center to the hole in the wall. 2 Drill 30 mm-depth guide holes according to the positions marked by stickers. 2 Lead the cables across the hole on the wall. 3 Mount the plastic rivets of self-tapping screws.
5 Mount your camera onto the wall and connect all cables. 6 Adjust the monitoring direction. 1 3 2 1 Adjust the opening of the Lead tapping screws through the guide holes in the base and fix them on the wall by using a screwdriver. universal joints as required. 2 Rotate the spherical hinge of 3 7 Power on your camera and adjust images. 5 the camera to get the desired monitoring direction. Tighten the locknut.
The preceding installation process is for concealed installation, during which holes are punched on the wall and cables are penetrated into the wall. If open installation is adopted, cables are not penetrated into the wall but threaded out from the outlet on one side of the base. Start Your Camera After verifying that your camera is properly mounted, connect the power cable to it and the other end of the cable to the mains. Then start your camera.
Waterproof Components for an RJ45 Plug 1 Attach the seal ring to the waterproof connector. 2 Mount the waterproof components. 3 2 1 Insert in order Seal ring 3 Insert the cylindrical waterproof ring into bolt. 4 Insert the cable into the connector and screw the waterproof bolt in. Cylindrical waterproof ring Waterproof bolt 5 Screw in the waterproof bolt lid. 6 Finish the waterproof installation.
In step 2, you can crimp the inner wires of the cable with the RJ45 plug first and then cover the waterproof components. You may also cover the waterproof components first. Waterproof Tail Cable Connect the tail cables and then take the following steps to protect the tail cables from water using waterproof tapes. The figures are only for illustration purpose. 1 Connect the tail cables. 2 Protect the connected cables using insulating tapes.
3 Protect other cables using insulating tapes. 4 Wrap all the tail cables together using insulating tapes. 5 Choose a start point for waterproof tapes. 6 Protect the tail cables using waterproof tapes.
Avoid short circuit when insulating the cables. Use self adhesive waterproof tapes that will stick together with the twisted cables. Tighten waterproof tapes when wrapping the cables and make sure the cable connections are fully covered. You are recommended to put the waterproof cables in a waterproof junction box which needs to be purchased separately.
Please contact your dealer to get the EZStation. Please refer to the user manual of EZStation for detailed information. 1. Connect your camera and your PC as shown in the figure below to ensure the routing is available. 2. Use EZStation to search online cameras automatically. 3. Modify your camera settings if necessary, including its IP address and subnet mask.
The default IP address is “192.168.0.13”. The default username is “admin” and the default password is “123456”. To access your camera from a different subnet, set the gateway for your camera after you log in. 5 Access Your Camera Access Your Camera Before you begin, check that: Your camera is operating properly and connected to the network. The PC you are using is installed with Internet Explorer 7.0 or later. IE 8.0 is recommended.
1. Open your browser, input the IP address of your camera (default IP is 192.168.0.13) in the address bar and then press Enter to open the login page. 2. Enter the username (default is “admin”) and password (default is “123456”) and then click Login. Install the ActiveX at your first login. For the detailed steps, see Install the ActiveX. When the installation of the ActiveX is completed, open your IE to log in.
1. Click Download. 2. Click Run to install the downloaded ActiveX. You may also click Save to download the file to your computer first. 3. Close the browser and follow the steps to complete the installation.
For your first login with Windows 7, if the system does not prompt you to install ActiveX, follow these steps to turn off UAC: click the Start button, and then click Control Panel. In the search box, type uac, and then click Change User Account Control Settings. Move the slider to the Never Notify position, and then click OK. After UAC is turned off, log in again. If the installation failed, open Internet Option in IE before login.
BOM: 3101C0C5
