Home Theater Master Preprogrammed 6 Learning Remote Control Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.
Table of Contents Page 2 3 Introduction Battery Installation 3 3 A. To Open and Close Battery Compartment Cover B. Low Battery Message 4 Using Your Remote Control 4 5 8 8 10 12 13 13 -- 16 17 17 18 - 18 19 --- 20 2 0 2 0 21 A. Function Table Reference Function Tables B. Preprogrammed Set Up Three Digit Code Method Auto Search Method Recalling the Set Up Code Number C.
introduction The Home Theater Master SL-9000 remote control is preprogrammed to operate over 1,000 Audio and Video components so that you can set it up by simply punching in a three digit code number that matches your equipment. The SL-9000 also has the ability to learn new functions from your original remote controls, allowing you to customize the remote to your own needs and update it as you add new equipment. Please refer to page 8 - 18 for instructions on setting up the remote control.
Battery installation This remote control uses four AAA 1.5 V batteries. Please be sure to match the batteries with the (+) and (-) markings inside the battery compartment during installation. A: To Open and Close the Battery Compartment Cover 1 To open the battery cover, push the latch forward toward the top of the remote control, and lift the latch up. I 2 To close the battery cover, slide the battery cover straight back in (toward the top of the remote) and push down until it “clicks” into place.
Using Your Remote A: Function Table Reference -PpIP- SHIFT TAPE TEST CENTEI HOME THEATER MASTER LEARNING REVOTE CONTROL 4 Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.
Using Your Remote Function Table No. Button Name Audio Functions SAT Functions TV Functions l-8 9 10 12 13 14 15 16 Device Name Power Mute TN Input VOL up VOL Down CH Up CH Down Up/Pause AUDIO (ON) On/Off (OFF) Mute Band/FM Vol up Vol Down Preset + Preset - SAT (ON) On/Off (OFF) Mute TV/SAT Vol up Vol Down Ch. + Ch. - TV (ON) On/Off (OFF) Mute TVlVideo Vol up Vol Down Ch. Up Ch. Down UP Down/Stop 18 19 20 RightfF.F.
Using Your Remote Function Table Button NameL Audio Functions SAT Functions TV Functions Device Name Power Mute TN Input VOL up VOL Down CH Up CH Down Up/Pause Down/Stop RightfF.F. Left/Rew Sel/Play Guide/I<< Menu/>>1 ExWRec Pre. ChJEject 1-O ; lO+ %“I. ,^ ,i AUDIO (ON) On/Off (OFF) Mute Band/FM Vol up Vol Down Preset + Preset - SAT (ON) On/Off (OFF) Mute TV/SAT Vol up Vol Down Ch. + Ch. - TV (ON) On/Off (OFF) Mute TVlVideo Vol up Vol Down Ch. Up Ch.
Using Your Remote Function Table No. Button Name VCR Functions Cable Functions 1-8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25-34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Device Name Power Mute T/V Input VOL up VOL Down CH Up CH Down Up/Pause Down/Stop Right/F.F. Left/Rew Sel/Play Guide/I<< Menu/>>1 ExWRec Pre. Ch./Eject 1-O lO+ Enter/Shift Fav/Sleep Info/Pro. L. Next/3 Ch. AWTest Tuner Rear Up Center Up Delay Up Surr.
Ushg Your Remote Function Table No. Button Name CD Functions Device Name Power Mute T/V Input VOL up VOL Down CH Up CH Down Up/Pause Down/Stop Right/F.F. Left/Rew 20 SellPlay Guide/I<< 21 22 Menu/>>1 Exit/Ret 23 Pre. Ch./Eject 24 25-34 1-O lO+ 35 Enter/Shift 36 37 FavlSleep Info/Pro. L. 38 39 Next/3 Ch. 40 AR/Test 41 Tuner Rear Up 42 43 Center Up Delay Up 44 45 Surr.
using Your Remote B: Preprogrammed Set Up The Home Theater Master universal remote control can operate up to eight separate audio and video devices (equipment). To program the remote control for your devices, please use the following steps: Three Digit Code Method 1 Turn on the device you would like the remote control to operate, either manually or with your original remote control. 2 Find the three digit Set-Up Code number for your device from the tables on pages (38 - 55).
using Your Remote Note: SET appears in the LCD for 20 seconds to indicate that the remote control is ready to be programmed. The following steps must be entered while SET appears in the LCD. 4 Point the remote control toward the device that was turned on in Step 1 and press in the first three-digit SetUp Code number for that device using the number buttons (O-9) on the remote control. SET followed by the number will appear in the LCD.
Using Your Remote Auto Search Method Please use this method if none of the Set-Up Code numbers worked for your device during the standard set-up procedure or if the manufacturer or brand for your device is not listed in Set-Up Code Tables. 1 Turn on the device you would like the remote control to operate, either manually or with your original remote control. 2 Press the corresponding Device Button (TV, VCR, SAT, CBL, AUD, CD, DVD, or AUX) and the MUTE button, simultaneously. SET will appear in the LCD.
Using Your .Remote If you pass the correct Set-Up Code number, you can return to it by pressing the CHANNEL DOWN button, one Set-Up Code number at a time, until your device turns back on. Note: During programming, the signal for POWER ON and POWER OFF is located on the MUTE button. For devices that use separate POWER ON and POWER OFF buttons, pressing the MUTE button on the remote control during programming will only turn the device OFF.
Ushg Your Remote Recalling the Set-Up Code Number To display the three digit Set-Up Code number that was stored for a device. 1 Press the Device Button and MUTE button, simultaneously. SET will appear in the LCD. 2 Press the T/V button. The LCD will quickly flash the three digit Set-Up Code number that was stored for your device in that mode. 3 Please write your Set-Up Code numbers in the chart below, for future reference.
Using Your Remote C: learning Set Up The Home Theater Master SL-9000 has the ability to learn new functions from your original remote controls: There are 8 “pages,, of learning with each page corresponding to the 8 Device modes on the remote control: AUDIO, CD, DVD, AUX, SAT, TV, VCR, CBL. All buttons in all Device modes can learn, except the LIGHT button. The 8 Device buttons at the toy of the remote control labeled (AUD, CD, DVD, SAT, l-I-$ VCR and CBL) learn only in the Audio mode.
Using Your Remote 3 Press and hold both the Device button selected in Step 1 and the SEL/PLAY button for about three seconds, until the LCD on the SL-9000 shows LEARN. The SL-9000 is now in the learning mode. Dezdcc Bu f fom SELIPLAY Btr ttolz Note: Each of the following steps must be completed within 20 seconds. If the remote does not receive any new commands within the allotted time, it will return to its liormal operating mode.
Using Your Remote Repeat Steps 4 through 7 for any other buttons you wish to learn new functions. 8 Once you have completed the learning for all the desired buttons in a Device mode, store the learned functions by pressing the Device and SEL/ PLAY buttons simultaneously, once again. The LCD in the SL-9000 will show SAVED and then return to the Device Mode. T h e remote has now returned to the original operating mode. Once you have stored the learned functions, test the buttons that have been taught.
Using Your Remote Learning New Functions on Device Buttons The eight Device buttons at the top of the remote control can also learn new functions. These buttons can only be set up in the Audio mode. If a new function is learned on a Device button, the new function will override any existing preDrogrammed information on the Device button. I v 1 Place the SL-9000 and the original remote control to be learned from, on a flat surface. Line up the remote controls head to head, about 2 to 3 inches apart.
using Your Remote Repeat steps 3 through 6 for any other Device buttons you wish to teach new functions. 7 Once you have completed the learning for all the desired Device buttons, store the learned functions by pressing the AUDIO and SEL / PLAY buttons simultaneously, once again. The LCD in the SL-9000 will show SAVED and then return to the AUDIO mode. The remote has now returned to the original operating mode.
Using Your Remote Erasing All Buttons in One Device Mode: 1 Press the Device button for the mode to be erased. 2 Press and hold the Device and SELlPLAY buttons simultaneously, for about 3 seconds, until the LCD shows LEARN. 3 Press and hold the Device and LIGHT buttons simulta- neously, for approximately five seconds and then release the buttons. The LCD will flash ERASE and then alternately CLEAR and the Device Mode. Note: This procedure takes about two minutes to complete.
Using Your Remote D: Operation After you have programmed the remote control for your equipment, use the following procedures to operate your home entertainment svstem: J 1 Press the Device Button that you wish to operate: e.g. to operate a TV, press the TV Device Button; to operate a VCR, press the VCR Device Button, etc. 2 Aim the remote control at the device and press the POWER button to turn on the device. 3 Press the buttons that send out the commands you desire.
using Your Remote .’ 4 : *’ : ^ ”’ Device Buttons Pressing a Device button at the top of the remote performs the following functions: 1 . Changes the Device mode on the SL-9000 remote control. 2. Sends out a Power ON command for the Device, if applicable. 3. Sends out a preprogrammed or learned Audio receiver1 preamplifier INPUT SELECTION, if applicable. 4. Toggles between the Main Device mode and the Automatic Audio Mode. Note: Device buttons can learn new information only in the Audio mode.
. :. Ushg Your - r;‘ Example: Pressing the SAT Device button a second time will change the LCD from SAT to A-SAT. Main Device Mode Automatic Audio Mode In the Automatic Audio Mode, you gain control of the receiver or preamplifier volume and surround levels while also maintaining full control of the Channel, Transport and Numeric Keypad of the device in the same mode.
After you set-up the remote control to operate your equipment, you can also program advanced features on the remote control. The advanced features are designed to enhance the use of the remote control with your home entertainment system. At Punch Throughs Volume Control “Punch Through” You can program the remote control so that either the AUDIO or TV Volume Control (VOLUME Ul? DOWN AND MUTE) will also operate in other modes on the remote control.
Advanced Features To Return to the Original Setting: 1 Select the mode that you want to turn off the Volume Control “Punch Through. If 2 Press the corresponding Device Button and the MUTE button, simultaneously. SET will appear in the LCD. 3 Press the VOLUME UP button. PUNCH will appear in the LCD. 4 Press the same Device Button, again. The DEVICE Mode will flash in the LCD. The AUDIO or TV Volume Control “Punch Through” is now turned off.
Advanced katum 4 Press either the VCR Device Button to set-up for VCR Channel Control or the CBL Device Button to set-up for Cable Channel Control. Either VCR or CBL will flash in the LCD, depending on the Device Button selected. VCR or Cable Channel Controls will now override the original CHANNEL UP and DOWN in this mode. To Return to the Original Setting: 1 Select the mode that you want to turn off the Channel Control “Punch Through.
Advanced kuturp I,_i‘ 3 , :_I .:,, ^’ 2 q Transport Control “Punch Through” You can set-up your remote control so that VCR or CD Transport Controls (PLAY, STOP, FAST FORWARD, REWIND, PAUSE, and RECORD) will also operate in other modes on the remote control. Transport Controls Example: Control VCR functions while operating the remote control in the TV mode.
Advanced Features The VCR or CD Transport Controls (PLAY, STOP FAST FORWARD, REWIND, PAUSE, and RECORD) will now override the original functions of the buttons in this mode. To Return to the Oriainal Settina: 1 Select the mode that you want to turn off the Transport J d Con fro1 “Punch Through. ” 2 Press the corresponding Device Button and the MUTE button, simultaneously. SET will appear in the LCD. 3 Press the SELECT/PLAY button. PUNCH will appear in the LCD. 4 Press the Device Button again.
Advanced Features B: Memory Buttons The buttons labeled Ml, M2, M3, M4, and POWER are Memory Buttons. The Ml-M4 buttons can store your favorite channels, create macro commands, or be used to “relocate” functions from one mode to another. The POWER button can operate either as a POWER button for a single device or as a memory button, when you program it. Note: Because the POWER button can also be programmed as a Memory Button, the MUTE button is used to enter POWER commands during Memory Button programming.
Advanced Featutzs Macro Commands: Memory Buttons can store multiple selections including Power On / Off sequences. l Example: In the Audio mode, the POWER Memoy Button can be programmed to turn on the TV, turn on the Audio receiver, turn on the VCR and turn on the Satellite receiver with one button push. “Relocating” Functions: Memory Buttons can be programmed to store functions from one mode into other modes.
Advanced katuru)s . ” . . .~. Programming Memory Buttons: 1 Select the mode that you wish to program the Memory Button in by pressing the corresponding Device Button (TV, VCR, CBL, SAT, or AUD) and MUTE button, simultaneously. SET will appear in the LCD. 2 Press one of the Memory Buttons (Ml, M2, M3, M4, or POWER) into which you wish to store the functions. M(l-5)_# # will appear in the LCD. 3 Press in up to ten commands that you want stored in that Memory button.
1 Press the Audio Device Button and the MUTE button, simultaneously. SET will appear in the LCD. 2 Press Memory Button M2. M2_ # # will appear in the LCD. 3 Press the MUTE button (to turn on the Audio receiver) M2_01 will appear in the LCD. Press the TV Device Button (to change to the TV mode) M2 02 will appear in the LCD. Press theMUTE button (to turn on the TV) M2 03 will appear in the LCD. Press theVCR Device Button (to change to the VCR mode) M2 04 will appear in the LCD.
Using Your Remote C. Changing the LCD Display Four different LCD displays can be selected for each Device mode of the remote control. To select an alternate LCD display, please use the following procedure: 1 Press and hold the Device button for which you would like to change the LCD setting. 2 While pressing the Device button, press and release the MENU button. Each time the MENU button is pressed, the LCD will show one of four displays.
Advanced Features LCD Displays in the Automatic Audio Mode A-SAT A-TV A-VCR A-CAB AUDIO A-CD A-DVD A-AUX A-V4 A-TV3 A-V1 A-V2 AUDl A-A2 A-A3 A-A4 A-TV2 A-V2 A-VID A-TV2 RECVR A-DVD A-LD A-TPE A-VC2 A-PRJ A - V C 2 AUD2 A - S U R A - L S R A - W E B A-V3 D: Programming a Second TV, VCR, etc. to Other Device Buttons. This feature is used to program the remote control for two or more TVs, VCRs, etc., or to program a device into a mode with a different Device Button name.
Advanced katures :> Your device will turn off when the correct Set-Up Code number has been selected. If it does not turn off, select the next Set-Up Code number from the table, and press in that code number. When your device turns off, proceed to Step 6. 6 Press the Device Button that was selected in Step 2. to store the Set-Up Code number. PASS will flash in the LCD to confirm the programming.
Model SL-9000, infrared remote control. Power Four 1.5 V AAA Batteries. Dimensions (h/w/d) 8.88 x 2.5 x 1.25 inches Weight 6.5 oz. (with batteries) Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.
Glossary Cursor Control Buttons that correspond to the UP, DOWN, LEFT, RIGHT, SELECT, GUIDE, MENU and EXIT functions of your audio / video equipment. Device Audio or video equipment, e.g. Television, VCR, Cable box, Audio receiver, Satellite receiver, etc. Device Button Any of the eight buttons located at the top of the remote control labeled AUD, CD, DVD, AUX, SAT, TV, VCR and CBL. Device Buttons are used to select modes of operation and to program the remote control.
Glossary Punch Through Advanced feature that enables you to operate Volume, Channel or Transport Control functions of one device while in another mode. Example: Audio Volume Control “Punch Through,” gives you the ability to raise, lower and mute your Audio receiver volume while operating the remote control in the TV mode. Set-Up Code Number The three-digit number that is used to program the remote control for your particular manufacturer or brand of audio/ video equipment.
Appendix A: Assignment of Audio/Video Equipment Please use the following listing to locate the correct Set-Up Code Tables for your equipment: AUDIO Set-Up Code Table: Audio Receivers, Preamplifiers, Surround Processors Satellite Set-Up Code Table: DSS, Primestar, DBS, Echostar, C Band receivers TV Set-Up Code Table: TVs, Monitors, Video/LCD Projectors VCR Set-Up Code Table: VCRs, TV/VCR combination units CABLE Set-Up Code Table: Cable Boxes, Internet/TV Set-Tops CD Set-Up Code Table: CD Players,
Set-Up Code Tables Audio Manufacturer/Brand Set-Up Code Number ADCOM AIWA AKAI AMC ANAM ANGSTROM ARCAM AUDIO ACCESS AUDIO ALCHEMY AUDIO DESIGN AUDIO EASE AUDIO MATRIX AUDIOFILE AUDIO TECHNICA B&K BOSE BRYSTON CARVER CASIO CHIRO CINEMA SOUND CITATION CLARION CURTIS MATHES DENON ELAN ENLIGHTENED AUDIO FISHER FOSGATE GE GOLDSTAR HARMAN KARDON HITACHI JC PENNY JENSEN 082092225161 018104170188202203211213 138 189 125 126127128 081 142 141 147 135 011084087088089194221 021 167 071 134 096 097 070 170 023 0060
&t-Up Code Tables Audio ’ Manufacturer/Brand Set-Up Code Number LUXMAN LX1 MAGNAVOX MARANTZ MCINTOSH MCS MERIDIAN MITSUBISHI MONDIAL NAD NAKAMICHI NEC ONKYO OPTIMUS PANASONIC PARASOUND PHILIPS PIONEER PROCEED RCA REALISTIC ROTEL SAMSUNG SANSUI SANYO SCOTT SEARS SHARP SHERWOOD SONY SOUNDESIGN SOUNDSTREAM SSI SUM0 TEAC TECHNICS THETA DIGITAL TOSHIBA WARDS YAMAHA ZENITH 004 009 052096115137139165 056 076 086152164208 006028031040063185186251 238 009 076 079 012 013 100 021204 242 243 042043112157158 113 1
Set-Up Code Tabk Satellite I I Manufacturer/Brand Set-Up Code Number AMPLICA BIRDVIEW BSR CAPETRONICS CHANNEL MASTER CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTROHOME EUROSAT FUJITSU GENERAL ELECTRIC GENERAL INSTRUMENT HITACHI HOME CABLE HOUSTON TRACKER HUGHES HYTEK ICR JANIEL JERROLD KATHREIN LEGEND LUXOR MACOM MEMOREX NEXTWAVE NORSAT PACE PANASONIC PANSAT PERSONAL CABLE PHILIPS PICO PL PRESIDENT PRIMESTAR PROSAT 050 051113126129 053 053 013 014 015 018 036 055 008 009 012 077 054 0
Set-Up Code Tabks Satellite Manufacturer/Brand Set-Up Code Number PROSCAN RCA REALISTIC SAMSUNG SATELLITE SERVICE SCIENTIFIC ATLANTA SONY STARCAST SUPERGUIDE TEE COM TOSHIBA TOWN & COUNTRY UNIDEN 001106 US ELECTRONICS VIEWSTAR WINEGARD ZENITH 001106 043 074 123 028 035 047 085 032 138 103 041 020 023 026075 087088090 107130137 002 127 023 026 016025042043 044045048049078079080086 101135 136 023 115 128 146 081082 083 084 091120 Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.
Set-Up Code Tabks TV Manufacturer/Brand Set-Up Code Number ADMIRAL AKAI AMARK AMPRO AMSTRAD ANAM AOC BLAUPUNKT CANDLE CAPEHART CETRONIC CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROWN CURTIS MATHES cxc DAEWOO 072081160161 001146 112 143 073 167 052 043054056080104112131 001004 112 058 088 001002 003 004 058 043 001002 003 004 043 101103 143 043 004 043 050 051 143 043 054 043 143 001101004 143 043 004 016 017043 044 055 071076103107111114 120123125127143 004 143 177 043 062 187 024 143 001004005 02
Set-Up Code Tab/es TV Manufacturer/Brand Set-Up Code Number JENSEN 013 034038070083145 043 001070 002 059 143 001043 143 154 072 072 004 166007015052081160164 001003 004 022 059 060 061063 064 127 160 164 094 001164 164 007 072 004 088 001004 024 028 042 088 004 024 028 040 042 109 124 146 191 001004062101 015 025 132130134001040016024056019 043 043 043 019 081 034056080092164 001003 024 056 059 060 063 064 164 004 001003 004005 038 059093127164 001018023025116135190 004 143 144160161165167 004 05813114
Set-Up Code Tables TV Manufacturer/Brand Set-Up Code Number SANYO SCOTT SEARS SHARP SIEMENS SIGNATURE SONY SOUNDESIGN SPECTRICON sss SUPRE MACY SYLVANIA TANDY TATUNG TECHNICS TECHWOOD TEKNIKA TELEFUNKEN TELERENT TERA TMK TOSHIBA TOTEVISION UNIVERSAL VIDEO CONCEPTS VIDIKRON VIDTECH WARDS YAMAHA YORK YUPITERU ZENITH ZONDA 166007020053057082 004 028 043 048 143 015030004007028057143094160082165 170081019028029014004022143175 088 072 070085139147126185 004 028 003 043 112 004 043 002 00100305906006306416404
Set-Up Code Tabk VCR Manufacturer/Brand Set-Up Code Number AIWA AKAI AMPRO ANAM AUDIO DYNAMICS BROOKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO DAYTRON DBX DYNATECH ELECTROHOME EMERSON 034 016043 046124125142146 072 031 012 023 039 043 035 037 129 028 031 108 003 040 135 031041 005 007010065108110111112116117119 108 012 023 039 043 034 053 059 006017025027029031034035036037046101 129131138153 003 008 009 010 034 031063072107109144147 132 136 155 012013020101106114123 012 045 004018026034043 063137150
&t-Up Code Tabk VCR Manufacturer/Brand Set-Up Code Number MITSUBISHI MTC MULTITECH NEC NORDMENDE OPTONICA PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PULSAR QUARTZ QUASAR RADIO SHACK RCA REALISTIC RICO RUNCO SALORA SAMSUNG SANSUI SANYO SCOTT SEARS SHARP SHINTOM SIGNATURE SONY SOUNDESIGN STS SYLVANIA SYMPHONIC TANDY TATUNG TEAC TECHNICS TEKNIKA THOMAS 013 020 045 046 051059 061142 151 034 040 024 034 012 023 039 043 048 043 053 054 066070083133140145 013 020 031063 031034 067 031034 054 067 071
Manufacturer/Brand Set-Up Code Number TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH VICTOR VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA ZENITH 006 008013042047059079082112131 040 101 040 012 048 012 034 046 141 040 003 013 017 024 031034 040 053 054 131 012 034 039 043 034048056058072080101 Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.
Set-Up Code Tabks , Cable ‘ i ’ IX .
Manufacturer/Brand Set-Up Code Number REGENCY REMBRANT RK SAMSUNG SCIENTIFIC ATLANTA SHERITECH SIGNAL SIGNATURE SL MARX SONY SPRUCER STARCOM STARGATE SYLVANIA TADIRAN TANDY TELECAPATION TEXSCAN TOCOM TOSHIBA UNIKA UNITED CABLE UNIVERSAL VIEWSTAR ZENITH 057 025 091 030 068 003 011041042043 045 046 022 030 001 030 096 047 078 002004008009 008 030 097 067 030 017 021 029 067 039 040 056 052 007 014 024 004 053 005007014024026027032035 012015018086087088089 052 060 093 Smarthome.com, Inc.
Set-Up Code Tabks CD Manufacturer/Brand Set-Up Code Number ADCOM AIWA AKAI AMC ARCAM AUDIO ACCESS AUDIO EASE AUDIOFILE AUDIO TECHNICA BSR CALIFORNIA AUDIO CAPETRONIC CARRERA CARVER CASIO CLARINETTE CREEK CROWN DENON EMERSON FISHER FRABA FUNAI GENEXXA GOLDSTAR HAITAI HARMAN KARDON HITACHI INKEL JC PENNY JENSEN 062 042 059 065 088089105 122170 187 074 195 202 231232 238 119 147 165 229 046 037 057 008 103 063 057 080 001041044 050 086 107 130 134 135 138 139 167 203 204 111182 182 159 035 002123206207 042
Set-Up Code Tabks CD Manufacturer/Brand MCINTOSH MCS MEMOREX MERIDIAN MGA MISSION MISUBISHI MITSUMI MODULAIRE MONDIAL NAD NAKAMICHI NEC NIKKO NSM ONKYO OPTIMUS PANASONIC PARASOUND PHILIPS PIONEER PROCEED PROTON QUASAR RADIO SHACK RCA RCX REALISTIC ROTEL RUNCO SAE SAMSUNG SANSUI SANYO SCOTT SHARP SHERWOOD SIGNATURE SONY SOUNDESIGN SUM0 Set-Up Code Number 212 014 073 092 010 094 025 044 107 121 153 182 147 006 005 067 122 095 217 218 219 014 062 046 044 107 030038039168 010013049050057058081082083085093 008
Set-Up Code Tabks Cn -L- ’ . Manufacturer/Brand Set-Up Code Number SYLVANIA SYMPHONIC TAEKWANG TANDY TEAC TECHNICS TECHWOOD THETA DIGITAL TOSHIBA VECTOR RESEARCH VICTOR WARDS YAMAHA YORX 044 107 052 181 074 195 010 015034036051052101131140 008060068103113172192200 076 032 234 235 006067091106148152160 080 004 022 114 124 001033 012 024 046 054 129 182 Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.
M-Up Code Tabks DVD Manufacturer/Brand Set-Up Code Number 004 AIWA AKAI 005 CALIFORNIA AUDIO 008 DAEWOO 230 007 206 207 DENON 026 027 GE GOLDSTAR 057 223 HITACHI 011 012 JVC KENWOOD 152 LOTTE 032 MAGNAVOX 032 035 MERIDIAN 035 MITSUBISHI 017 NAD 121 ONKYO 035 OPTIMUS 049 PANASONIC 008 021068 113 PHILIPS 032 035 PIONEER 023 106 107 PROSCAN 026 REALISTIC 049 RCA 002 027 RUNCO 127 SANYO 075 SAMSUNG 056 229 SHARP 120 152 SONY 033 053 110 TECHNICS 008 068 113 THETA DIGITAL 032 235 THOMPSON 026 027 TOSHIBA 035 1
Set-Up Code Tabk AUX .
Manufacturer/Brand Set-Up Code Number TECHNICS TOSHIBA TURBOSCAN VICTOR x-10 XANTECH YAMAHA 007010076088109122193 112 167 106 183 168169170171172188189 021026 031067 Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.