RTS Pocket Programming Guide
Table of Contents P.2 How Does RTS Work? P.3/4 Identify RTS Control Options Transmitters P.5 Telis Hand-Held Remote P.6 Telis Soliris Hand-Held Remote P.7 Telis Modulis Hand-Held Remote P.8 Telis 16 Channel Hand-Held Remote P.9 DecoFlex Wireless Wall Switch P.10 DecoFlex Table Top Accessory P.11 Telis 6 Channel Chronis RTS Hand-Held Timer Receiver P.12 Outdoor Lighting Receiver P.12 Outdoor Universal Receiver Interface P.13 Universal RTS Interface (URTSI) Repeater P.14 RTS Repeater Sensors P.
RTS Motor Range P.27 P.27 P.27 P.28 P.28 P.28 P.29 P.29 P.29 P.30 P.30 P.30 P.30 CT32 Cord Lift WireFree™ Tilt WireFree™ LT30 Roll Up WireFree™ ST30 Sonesse™ 30 ST40 Sonesse™ 40 Altus 40 ST50 Sonesse™ 50 Altus 50 LT50 RTS CMO Sunea RTS CMO Altus 60 Glydea™ 35 Glydea™ 60 Quick Programming Guides P.31-36 CT32 Cord Lift WireFree™ LT30 Roll Up WireFree™ ST30 Sonesse™ 30 ST40 Sonesse™ 40 Altus 40 ST50 Sonesse™ 50 Altus 50 Altus 60 P.37-42 Tilt WireFree™ P.43-46 LT RTS CMO P.47-50 Sunea RTS CMO P.
Home Motion by Somfy We’ve developed a brand expression that emphasizes the centerpiece of consumers’ lives, the home. It also represents Somfy’s mission, bringing homes to life by creating movement for all openings and allowing consumers to enjoy life’s daily pleasures for a better quality of life.
How Does It Work? Simply press a button on a remote control or wall switch and window coverings move with ease. There is no need to point or aim the transmitter at the covering because Radio Technology Somfy® (RTS) is omni-directional. And just like a garage door opener, the radio waves travel through walls.
Identify RTS Control Options Transmitters Hand-Held Remotes Users can control motorized window coverings by pressing a button or rolling a scroll wheel on a variety of hand-held RTS remotes. Wireless Wall Switches Users can easily control their motorized window coverings when entering or exiting a room with DecoFlex RTS Wall Switches. Table Top Remotes Users can control their motorized window coverings with the versatile DecoFlex Table Top remote.
Interface Users can convert Infrared, RS232, and RS485 protocol into RTS, allowing for 3rd party control of motorized window coverings. Repeater Users can extend the distance of motorized window covering control. Sensors Users can set sensors to automatically adjust motorized window coverings in accordance to the amount of sunlight received, temperature recorded, as well as the speed and direction of wind.
Telis Hand-Held Remote Features UP Button The “my” button acts as a stop button when the window covering is in motion. When the window covering is stationary, the “my” button brings it to the programmed favorite position. DOWN Button Channel LED All 4 lights will illuminate when fifth channel is activated.
Telis Soliris Hand-Held Remote Features UP Button The “my” button acts as a stop button when the awning is in motion. When the window covering is stationary, the “my” button brings it to the programmed favorite position. DOWN Button When left LED is lit the window covering will only react to wind control. When right LED is lit the window covering will react to both sun and wind control.
Telis Modulis Hand-Held Remote Features Open/Close buttons Scroll wheel for incremental tilt control of horizontal blinds and sheer horizontal products.
Telis 16 Channel Hand-Held Remote Features Signal Indicator On-Screen LCD Display Channel Number 16 channels can be used to control 16 individual motorized applications or 16 groups of motorized applications. Product Name (up to 8 characters: 7 Letters + 1 Number) Selection Button Channel Navigation Buttons UP Button Favorite position “my” Button The “my” button acts as a stop button when the window covering is in motion.
DecoFlex Wireless Wall Switch Features Programming Button (recessed) 5 Channel Button DecoFlex WireFree™ RTS Wall Switch shown in White Finish Also available in multiple finishes and various channel button versions: Ivory Black For a complete list of available pre-printed buttons please go to www.somfystore.com and search for “buttons”.
DecoFlex Table Top Accessory Features LED for each channel. Available in 1, 2, 3, 4 and 5 channel versions. Channel Buttons can be labeled for easy organization “STOP” button stops the window covering when it’s in motion. When the window covering is stationary, the “STOP” button brings it to the programmed favorite position.
Telis 6 Channel Chronis RTS Hand-Held Timer Features Signal Indicator On-Screen LCD Display Selection Button Channel Navigation Buttons UP Button Favorite position “my” Button The “my” button acts as a stop button when the window covering is in motion. When the window covering is stationary, the “my” button brings it to the programmed favorite position.
Outdoor Lighting Receiver Features *For programming instructions please go to P. 56 Control patio or deck lights with the same remote used for the awning. Controls incandescent, halogen lights or any outdoor device up to 500W. Fully compatible with the Telis RTS range of transmitters and the DecoFlex™ WireFree™ RTS wall switches. SEQUENTIAL CONTROL BUTTON PROGRAMMING BUTTON GROUND PROGRAMMING LED 500W Max Lighting Output NEUT HOT NEUT HOT LAMP 500 WATTS MAX.
Universal RTS Interface (URTSI) Features Antenna 9 Volt DC (power supply included) IR Sensor Port Rs485 Expansion RS232 or RS485 Input Allows user to convert infrared, RS232 and RS485 protocol into Radio Technology Somfy® (RTS) to allow for third party control. Offers 16 channels. Compatible with full range of RTS motors. With its compact and sleek design, the URSTI can be housed in a discrete location.
RTS Repeater Features Antenna The RTS Repeater receives the signal from a Telis RTS remote or DecoFlex WireFree™ wall switch or similar device and re-transmits the signal to an RTS compatible motor or receiver. Indicator Light Simply plugs into any 120V AC electrical outlet. No programming required. Should be placed approximately halfway between the transmitting device such as a Telis hand-held remote and the receiving device, the motor.
Sunis Indoor WireFree™ Sensor Features LED Indicator ON/OFF Selector Switch Control Setting Panel Programming Button Mode Button Sun Sensitivity Threshold Adjustment Front view with cover removed window sill mount The Sunis Indoor Sensor can be programmed to automatically adjust window coverings in accordance to sunlight threshold settings.
Thermo Sunis Indoor WireFree™ Sensor Features Sun & Temperature Sensitivity Threshold Adjustment Temperature LED Indicator ON/OFF Selector Switch Sunlight LED Indicator Programming Button Mode Button Control Setting Panel Front view with cover removed Function Selection Switch window sill mount The Thermo Sunis Sensor can be programmed to automatically adjust window coverings in accordance to sunlight and/or room temperature threshold settings.
Eolis 3D WireFree™ Wind Sensor Features Installed discreetly on the end of the front bar. Easy wireless installation. Automatically retracts the awning with the detection of wind generated movements. Easy to program. Maintenance free, long life batteries.
Outdoor Sunis WireFree™ Sensor Features Light sensing eye Solar powered sun sensor. Front View Easy wireless installation. Automatically adjusts shutters, awnings and window coverings when the programmed sunlight threshold is reached. Compact design allows for discreet mounting. Telis Soliris RTS remote recommended to control ON/OFF function.
Understanding Control Options: Applies to all Telis Hand-Held remotes. Channel 1: Individual Control of SHADE 1 Channel 2: Individual Control of SHADE 2 Channel 3: Individual Control of SHADE 3 Telis 4 RTS Hand-Held Remote *Fifth channel is activated when all 4 LEDs illuminate Channel 4: Individual Control of SHADE 4 *Channel 5: Individual Control of DRAPERY The Telis 16 channel remote features an LCD screen that numerically displays which channel is selected.
Individual Control DecoFlex WireFree™ RTS 5 Channel Button Version For a complete list of available pre-printed buttons please go to www.somfystore.com and search for “buttons”.
Understanding Control Options: Applies to all Telis Hand-Held remotes.
Group Control DecoFlex WireFree™ RTS Table Top Accessory For a complete list of available pre-printed buttons please go to www.somfystore.com and search for “buttons”.
Understanding Control Options: Applies to all Telis Hand-Held remotes. Channel 1: Individual Control of shade in SHADE 1 Channel 2: Individual Control of shade in SHADE 2 Channel 3: Group Control of blinds in BATHROOM Channel 4: Group Control of shades in OFFICE Telis 4 RTS Hand-Held Remote *Channel 5: Group Control of ALL motorized shades *Fifth channel is activated when all 4 LEDs illuminate The Telis 16 channel remote features an LCD screen that numerically displays which channel is selected.
Individual and Group Control DecoFlex WireFree™ RTS 5 Channel Button Version For a complete list of available pre-printed buttons please go to www.somfystore.com and search for “buttons”.
Product Application & ROLLER SHADE 12 V CT32 CORD LIFT WIREFREE™ 12 V TILT WIREFREE™ 12 V LT30 ROLL UP WIREFREE™ 24 V ST30 SONESSE™ 30 110 V ST40 SONESSE™ 40 110 V ALTUS 40 110 V ST50 SONESSE™ 50 110 V ALTUS 50 110 V 110 V LT50 RTS CMO SUNEA RTS CMO 110 V ALTUS 60 110 V GLYDEA™ 35 110 V GLYDEA™ 60 25 ROMAN/WOVEN SHADE 2” HORIZONTAL BLIND SHEER HORIZONTAL SHADE P P PP P P P P P P P P P P P P P P P P P
Motor Compatibility Chart PLEATED/ CELLULAR SHADES AWNINGS ROLLING SHUTTER P EXTERIOR SOLAR SCREENS MOTOR DETAILS PAGE DRAPERIES P.27 P.27 P.27 P P.28 P.28 P P P P.28 P.29 P P P P P P P P P P P P P.29 P.29 P.30 P.30 P.30 P.
RTS Motor Range CT32 CORD LIFT WIREFREE™ - BATTERY OR TRANSFORMER POWERED 23.1mm 12 V 31.2mm Side View PLEATED/ CELLULAR SHADES ROMAN/WOVEN SHADE TILT WIREFREE™ - BATTERY OR TRANSFORMER POWERED 31.
*Please note: If you cannot identify the motor or control being used, please contact Somfy customer service at 877-22SOMFY 24 V ST30 SONESSE™ 30 RTS - TRANSFORMER OR LOW VOLTAGE HARDWIRE 30mm motor diameter Side View ROLLER SHADE 110 V Side View ROMAN/WOVEN SHADE Side View AWNING SHEER HORIZONTAL SHADE PLEATED/ CELLULAR SHADES ST40 - SONESSE™ 40 RTS - HARDWIRED OR PLUG-IN 40mm motor diameter ROLLER SHADE 110 V 2” HORIZONTAL SHADE ROMAN/WOVEN SHADE 2” HORIZONTAL SHADE ALTUS 40 - HARDWIRED
RTS Motor Range 110 V Side View ST50 SONESSE™ 50 RTS - HARDWIRED OR PLUG-IN 50mm motor diameter ROLLER SHADE AWNING 110 V Side View 50mm motor diameter ROLLING SHUTTER 2” HORIZONTAL BLIND ROMAN/WOVEN SHADE EXTERIOR SOLAR SCREENS LT50 RTS CMO - HARDWIRED OR PLUG-IN 50mm motor diameter AWNING 29 2” HORIZONTAL SHADE ALTUS 50 - HARDWIRED OR PLUG-IN 110 V Side View ROMAN/WOVEN SHADE ROLLING SHUTTER EXTERIOR SOLAR SCREENS ROLLER SHADE
*Please note: If you cannot identify the motor or control being used, please contact Somfy customer service at 877-22SOMFY SUNEA - HARDWIRED OR PLUG-IN 110 V Side View 50mm motor diameter AWNING ALTUS 60 - HARDWIRED OR PLUG-IN 110 V Side View EXTERIOR SOLAR SCREENS 60mm motor diameter AWNING ROLLING SHUTTER GLYDEA™ 35 RTS - PLUG-IN 110 V 53mm 95mm Side View DRAPERY GLYDEA™ 60 RTS - PLUG-IN 110 V 53mm 95mm Side View DRAPERY 30
QUICK PROGRAMMING GUIDE FOR THE FOLLOWING RTS MOTORS CT32 CORD LIFT WIREFREE ALTUS 40 LT30 ROLL UP WIREFREE ST50 SONESSE 50 ST30 SONESSE 30 ALTUS 50 ST40 SONESSE 40 ALTUS 60 FACTORY MODE BEFORE YOU BEGIN Motors are shipped in FACTORY MODE without limit settings and transmitter Id’s. Power must ONLY be connected to current window covering being programmed. All other window coverings must be disconnected from their respective power while programming.
QUICK PROGRAMMING GUIDE FOR RTS MOTORS Check the Direction of operation If hand-held transmitter direction is not properly programmed, Eolis/Soliris RTS sensor will not function in the manner it was intended. Damage to motorized window covering and injury may occur as a result. During installation, it is mandatory to test and verify the motorized window covering operates in accordance to the commands from hand-held transmitter.
QUICK PROGRAMMING GUIDE FOR RTS MOTORS Programming Completed Step 4: Press and hold the PROGRAMMING BUTTON on the back of the transmitter until the window covering jogs. The window covering is now in USER MODE. In USER MODE, the window covering will operate with a brief PRESS on UP or DOWN (or maintained fashion). USER MODE Adjusting the Limits in User Mode To Change the Lower Limit: STEP 1: Press DOWN to send the window covering to it’s current LOWER Limit.
QUICK PROGRAMMING GUIDE FOR RTS MOTORS Send the window covering to the “MY” position by pressing from ANY window covering position. ! my (STOP) Window covering should be stationary prior to activating “MY” position function. If window covering is actively moving (in-motion) my (STOP) should be pressed twice.
QUICK PROGRAMMING GUIDE FOR RTS MOTORS Resetting All Pre-Programmed Limit Settings & Channels LT30 WIREFREETM ROLL UP MOTORS LT-30 RTS 12V DC Using a paper clip, press and hold the PROGRAM BUTTON located on the motor head until window covering jogs 3 times, then release button. All transmitters and limits will be erased (motor is now reset to FACTORY MODE). Motor limits will need to be reestablished. Please return back to PROGRAMMING MODE to initiate programming process.
QUICK PROGRAMMING GUIDE FOR RTS MOTORS Resetting Altus RTS 120 V AC Perform a Dual Power Cut to delete all previous settings and return motor to FACTORY MODE. 1 Remove plug from power for 2 Seconds 2 Plug-in power cord for 10 Seconds 3 Remove plug from power for 2 Seconds 4 Plug-in power cord. Window covering will begin to move. When the window covering stops, press and hold the PROGRAMMING BUTTON of any transmitter until the window covering jogs twice.
QUICK PROGRAMMING GUIDE FOR TILT WIREFREE™ RTS MOTOR FACTORY MODE BEFORE YOU BEGIN The following steps must be completed to ensure proper blind programming and functionality. Power should ONLY be connected to current blind being programmed. All other blinds should be disconnected from their respective power while programming is in progress. While programming, blind should not be inactive for longer than 2 minutes or motor will exit programming mode.
QUICK PROGRAMMING GUIDE FOR TILT WIREFREE™ RTS MOTOR Setting Limits Starting with Slats in DOWN Position STEP 1: Press and hold the UP or DOWN reach the desired LOWER limit (slat position). button on the transmitter to STEP 2: Once the desired lower limit (slat position) is reached, press and hold both the my (STOP) and UP button simultaneously until the blind begins to tilt upward, then release. STEP 3: Press the my (STOP) button when the blind reaches the desired UPPER limit (slat position).
QUICK PROGRAMMING GUIDE FOR TILT WIREFREE™ RTS MOTOR Completing Programming and Exiting PROGRAMMING MODE Step 6: Using a paperclip or pen, press and hold the PROGRAM BUTTON on the back of the transmitter until the blind jogs. TRANSMITTER IS NOW MEMORIZED AND PROGRAMMING IS COMPLETE. ! If power is disconnected from blind before this step is completed, TRANSMITTER WILL NOT BE MEMORIZED to the programmed blind however limits (slat positions) will remain programmed.
QUICK PROGRAMMING GUIDE FOR TILT WIREFREE™ RTS MOTOR Deleting Specific Channels/Transmitters STEP 1: Using a paperclip or pen, press and hold the PROGRAM BUTTON on the previously addressed transmitter until the blind jogs. ! Step 1 should not be performed with the transmitter intended for deletion. STEP 2: Select the desired channel (1-4 or all) or transmitter (single channel) to be deleted. STEP 3: Press and hold the PROGRAM BUTTON on the transmitter until the blind jogs.
QUICK PROGRAMMING GUIDE FOR TILT WIREFREE™ RTS MOTOR Re-adjusting Upper Limit (UP Slat Position) STEP 1: Press the UP the pre-set UP limit. directional button on the transmitter. Blind will tilt to STEP 2: Once blind stops at pre-set up limit, press and hold both the UP and DOWN buttons simultaneously on the transmitter until the blind jogs. STEP 3: Press and hold either the UP to adjust slats to new position.
QUICK PROGRAMMING GUIDE FOR TILT WIREFREE™ RTS MOTOR Modulis Only - UP Press momentarily on the UP button to open the blind slats. Press the my (STOP) button to stop the movement of the slats. Modulis Only - DOWN Press momentarily on the (DOWN) button to close the slats. Press the my (STOP) button to stop the movement of the slats. Modulis Only: Using the Scroll Wheel For precise slat positioning scroll the wheel of the Modulis transmitter to move the blind slats up or down.
QUICK PROGRAMMING GUIDE FOR LT RTS CMO MOTOR FACTORY MODE This mode allows for rotation direction modification and setting of the end limits. DESCRIPTION The LT RTS CMO is designed for rolling blinds, awnings and shutters. The LT RTS CMO must be programmed with the Inteo family of transmitters. The LT RTS CMO motors are compatible with a Soliris and Eolis RTS Sun & Wind sensors. ! BEFORE YOU BEGIN For initial programming, provide power only to the motor being programmed.
QUICK PROGRAMMING GUIDE FOR LT RTS CMO MOTOR PROGRAMMING MODE Initiate PROGRAMMING MODE STEP 1: Assign the transmitter to communicate with the motor’s receiver, press and hold the UP and DOWN buttons on the transmitter simultaneously. STEP 2: Release both buttons after the end-product jogs briefly UP and DOWN indicating that this transmitter can operate the motor during programming. The LT RTS CMO motor will now operate in a momentary fashion.
QUICK PROGRAMMING GUIDE FOR LT RTS CMO MOTOR USER MODE This mode is for operating the motor by the end user. Two intermediate positions my positions (IP1 & IP2) can be programmed into the LT RTS CMO motor. IP1 is set using the UP limit as a reference and IP2 is set from the DOWN limit as a reference. Intermediate Position 1 Recording the Intermediate Position (IP1) referenced from the UP Limit of the end-product.
QUICK PROGRAMMING GUIDE FOR LT RTS CMO MOTOR Adding Additional Transmitters/Sensors (Single Channel) STEP 1: Using a paperclip or pen, press and hold the PROGRAM BUTTON on the previously recorded transmitter until the awning jogs. STEP 2: Using a paperclip or pen, press and hold the PROGRAM BUTTON on the Additional (new) transmitter/sensor until the awning jogs. Resetting Back to FACTORY MODE Resetting Motor Memory and Recording New Transmitter Step 1: Perform a dual power cut in the following sequence: 1.
QUICK PROGRAMMING FOR SUNEA RTS CMO MOTOR FACTORY MODE DESCRIPTION The Sunea RTS CMO has 3 main features: 1. Universal motor for Retractable Awnings and Cassette Awnings 2. Back release function at top of end limit 3. Possibility to choose the closing force. BEFORE YOU BEGIN For initial programming, provide power only to the motor being programmed. For awning installations, an awning hood is strongly recommended and a drip loop should be formed to prevent water from entering the head of the motor.
QUICK PROGRAMMING FOR SUNEA RTS CMO MOTOR Check the Direction of Operation Press and hold UP or DOWN . When pressing DOWN product should go down or out. If awning direction does not correspond with UP or DOWN you must REVERSE the output direction. To reverse output direction, simply press & hold the my (STOP) until the awning jogs. Output direction should now correspond.
QUICK PROGRAMMING FOR SUNEA RTS CMO MOTOR STEP 3: Press and hold my (STOP) the button again until the awning moves to set its UPPER limit automatically and confirm STEP 4: Press and hold the PROGRAM BUTTON on the back of the transmitter until the awning jogs. It will now operate in a maintained fashion. Double check limits as a precaution. Adjusting the Limits To Change the LOWER Limit: Send the motor to its current LOWER limit position with the transmitter and let it stop.
QUICK PROGRAMMING FOR SUNEA RTS CMO MOTOR STEP 1: Set the awning to the lowest position. To Activate this Function: STEP 2: Press and hold both the my (STOP) and UP buttons simultaneously until the awning jogs. The motor is in PROGRAMMING MODE. STEP 3: Adjust the fabric's tension using the UP or DOWN buttons. STEP 4: Press the my (STOP) button until the awning jogs. The fabric's tension has been programmed.
QUICK PROGRAMMING FOR GLYDEA RTS DESCRIPTION 2 motors: Glydea 35 RTS, Glydea 60e RTS AC 120 V with integrated power supply 10 foot cable Motor placement left or right and/or upside down installation (Available 4th qtr) New touch motion (only on the 60e) Comes in Dry contact with optional RTS plug-in module Standard mounting False Ceiling Mounting BEFORE YOU BEGIN Manually move drapery to a middle position along the track. This allows for movement of the motor in either direction.
QUICK PROGRAMMING FOR GLYDEA RTS Back Release Setting : Glydea 35 RTS Only ! It is required to set a back release position on thick draperies in order to allow proper manual operation. Press briefly the OPEN/UP OPEN/UP end limit button to move the drapery to the STEP 1: Press and hold the my and CLOSE/DOWN buttons simultaneously until the drapery jogs. Press the CLOSE/DOWN button to re-adjust the back release position.
QUICK PROGRAMMING FOR GLYDEA RTS CLOSE/DOWN Limit Adjustment: STEP 1: Press the CLOSE/DOWN button to move the drapery to the limit to be re-adjusted. STEP 2: Press and hold the OPEN/UP eously until the drapery jogs. and CLOSE/DOWN STEP 3: Press and hold the OPEN/UP or CLOSE/DOWN the drapery to the new desired position. STEP 4: To confirm the new limit, press and hold the the drapery jogs.
QUICK PROGRAMMING FOR GLYDEA RTS STEP 3: Press the OPEN/UP and CLOSE/DOWN buttons simultaneously until the drapery jogs to switch from no touch motion to low sensitivity; to high sensitivity; to high sensitivity and back to no touch motion. STEP 4: Press the my (STOP) button until the drapery jogs to confirm the setting.
QUICK PROGRAMMING FOR OUTDOOR UNIVERSAL RECEIVER RTS PROGRAMMING MODE Add The First Transmitter To The Memory Step 1: Press the PROGRAMMING BUTTON, on the Outdoor Universal Receiver RTS for more than 2 seconds. Step 2: The programming LED on the receiver will illuminate on and the motor will jog. Step 3: Press the PROGRAMMING BUTTON on the new transmitter to record it to the receiver. The programming LED on the Receiver will blink, and the motor will jog indicating the transmitter is memorized.
QUICK PROGRAMMING FOR OUTDOOR LIGHTING RECEIVER RTS PROGRAMMING MODE Add The First Transmitter To The Memory Step 1: Press the PROGRAMMING BUTTON, on the Outdoor Lighting Receiver RTS for more than 2 seconds. Step 2: The programming LED on the receiver will illuminate, and the lamp will light for 2 seconds. Step 3: Press the PROGRAMMING BUTTON on the new transmitter to add it to the receiver. The programming LED on the Receiver will blink, and the lamp will light indicating the transmitter is memorized.
QUICK PROGRAMMING FOR UNIVERSAL RTS INTERFACE (URTSI) PROGRAMMING MODE Set the RTS receiver or motor into its PROGRAMMING MODE. Refer to the installation instructions of the relevant RTS receiver or motor for this procedure. ! For initial programming provide, power only to the motor or control being programmed. Using the rotary switch, select the channel to be programmed. Letter A through F stand for channels 10 through 15, 0 for 16. Briefly press the PROGRAMMING BUTTON (1 sec. max.
QUICK PROGRAMMING FOR SUNIS INDOOR WIREFREE SENSOR PROGRAMMING MODE Adding a Sunis Indoor Sensor ! During initial programming, provide power only to motorized window covering being programmed. STEP 1: Carefully remove rear cover to expose sensor control setting panel. STEP 2: Slide the ON/OFF Selector Switch to the ON or position. STEP 3: Set the motorized window covering into PROGRAMMING MODE (Refer to the installation instructions of the relevant RTS receiver or motor or this procedure).
QUICK PROGRAMMING FOR SUNIS INDOOR WIREFREE SENSOR Setting the Light (Sun) Sensitivity (Threshold) Sunis sensor should be mounted in or near window and exposed to incoming light. STEP 1: Carefully remove rear cover of Sunis Light sensor exposing control setting panel. STEP 2: Slide the ON/OFF Selector Switch to the ON or position. STEP 3: Momentarily press the MODE BUTTON. LED Indicator will illuminate for approximately 15 seconds.
QUICK PROGRAMMING FOR SUNIS INDOOR WIREFREE SENSOR Replacing the Battery The Sunis WireFree™ RTS Light Sensor uses a lithium battery (Type: CR2430). LED Indicator Light will illuminate orange when battery needs replacing. STEP 1: Carefully remove rear cover of Sunis light sensor exposing the control setting panel (See Figure 4 pg. 62). STEP 2: Firmly grip the molded indentations and rotate control setting panel counter clockwise to open position.
QUICK PROGRAMMING FOR SUNIS INDOOR WIREFREE SENSOR Programming Figures FIGURE 2 Window Glass Mount Window Sill Mount Sun Sensitivity Selector FIGURE 3 LED Indicator ON/OFF Selector Switch Control Setting Panel (-) Requires (+) Less Sunlight Requires More Sunlight Mode Button FIGURE 4 Rear Cover Sensor Case Control Setting Panel 61
QUICK PROGRAMMING FOR THERMO SUNIS INDOOR WIREFREE SENSOR Adding a Thermo Sunis Indoor Sensor ! During initial programming, it is recommended that power is provided only to motorized window covering being programmed. STEP 1: Carefully remove rear cover to expose sensor control setting panel. STEP 2: Set the motorized window covering into PROGRAMMING MODE (Refer to the installation instructions of the relevant RTS receiver or motor for this procedure).
QUICK PROGRAMMING FOR THERMO SUNIS INDOOR WIREFREE SENSOR Setting the (Temperature) Sensitivity (Threshold) Thermo Sunis should be mounted in or near window and exposed to incoming sunlight. STEP 1: Carefully remove rear cover of the Thermo Sunis sensor exposing Control Setting Panel (See Figure 4 pg. 67). STEP 2: Slide the ON/OFF Selector Switch to the ON or position. Sun LED Indicator will illuminate for 5 seconds and then extinguish.
QUICK PROGRAMMING FOR THERMO SUNIS INDOOR WIREFREE SENSOR Setting the (temperature) Sensitivity (threshold) Thermo Sunis should be mounted in or near window and exposed to incoming sunlight. Step 1: Carefully remove rear cover of the Thermo Sunis sensor exposing Control Setting Panel (See Figure 4 pg. 67). Step 2: Slide the ON/OFF Selector Switch to the ON or position. Sun LED Indicator will illuminate for 5 seconds and then extinguish. Step 3: Momentarily press the MODE BUTTON.
QUICK PROGRAMMING FOR THERMO SUNIS INDOOR WIREFREE SENSOR OPERATING MODE ! Default employs output response time delays. STEP 1: Slide the Sun/Temp Selector Switch to the desired setting (See Figure 3 pg. 67). = Activation of Window Covering via Sunlight only = Activation of Window Covering via Temperature & Sunlight STEP 2: Adjust Sunlight and Temperature Sensitivity (threshold) (Refer to Setting theSensor Sensitivity (threshold).
QUICK PROGRAMMING FOR THERMO SUNIS INDOOR WIREFREE SENSOR *When selected for use with Interior Window Coverings, the Thermo Sunis sensor will provide RTS commands to preset window covering limits = (Go to DOWN Limit) = (Go to UP Limit). ! Activation of Window Covering Via: Temperature & Sunlight When (Sun & Temperature) control is selected, the Temperature threshold setting will TAKE PRIORITY over the Sun Threshold Setting.
QUICK PROGRAMMING FOR THERMO SUNIS INDOOR WIREFREE SENSOR Programming Figures FIGURE 2 Window Glass Mount Window Sill Mount FIGURE 3 ON/OFF Sun/Temp Selector Switch Sun LED Indicator Temperature LED Indicator * Sun Sensitivity (Threshold) Selector * Temperature Sensitivity (Threshold) Selector Mode Button Control Setting Panel Function Selector Switch 123 Command Modes Note: Sensitivity Threshold (-) less sunlight (+) more sunlight FIGURE 4 Rear Cover Sensor Case Control Setting Panel 67
QUICK PROGRAMMING FOR EOLIS 3D WIREFREE™ WIND SENSOR BEFORE YOU BEGIN Make sure the "DOWN" button on the remote extends the awning. If this is incorrect please refer to relevant motor/receiver instructions to revearse the direction of operation for the awning. Failure to correct this error will cause damage to awning by extending it during windy conditions. Awning Awning Front Bar Eolis 3D ADDING BATTERIES Clear awning of any debris and make sure surface of awning is clean.
QUICK PROGRAMMING FOR EOLIS 3D WIREFREE™ WIND SENSOR STEP 3: Adjust the sensor dial to (4). (1= Most sensitive, 9= Least sensitive) STEP 4: Put the sensor electronics back in the housing. STEP 5: Slide the housing back on the mounting plate. STEP 6: Test the sensor by pushing up and down on the awning front bar or arm until it begins to retract. You can use the remote to stop the awning after 5 seconds (first test mode). STEP 7 : Bring the awning back out and test it again.
QUICK PROGRAMMING FOR OUTDOOR SUNIS WIREFREE SENSOR STEP 1: Place Sunis in a sunny area to charge for 10 minutes. STEP 2: Completely retract the awning. Then press the PROGRAMMING BUTTON on the back of the original remote using a paper clip, pen or similar device until the awning jogs. STEP 3: Press the PROGRAMMING BUTTON on the back of the Sunis until the awning jogs. STEP 4: Turn intensity knob on the Sunis completely counter clockwise and allow direct sunlight to shine on the front for 2 minutes.
QUICK PROGRAMMING FOR TELIS 16 RTS DESCRIPTION The Telis 16 RTS remote control allows you to control up to 16 end-products or groups of end-porducts using Radio Technology Somfy (RTS) BEFORE YOU BEGIN We recommend that each motor is programmed in advance using an individual Telis 1 RTS transmitter and that the limits of each motor are set. However, like any RTS remote control transmitter, the Telis 16 RTS can be used for motor programming operations (limit switch adjustment, etc.
QUICK PROGRAMMING FOR TELIS 16 RTS STEP 7: Briefly press the SELECTION button to save the character displayed and move to the next character. STEP 8: Repeat steps 4 to 7 for each of the characters in the channels name. STEP 9: Press and hold the SELECTION button until SET is no longer displayed on the screen SET MODE is deactivated, and the Telis 16 Chronis RTS returns to MANUAL MODE.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS DESCRIPTION The Telis 6 Chronis RTS remote control transmitter allows you to control up to 6 end-products or groups of window coverings using Radio Technology Somfy (RTS). The Telis 6 Chronis can be used in 2 ways: in either MANUAL or AUTOMATIC MODE. MANUAL MODE allows you to control window coverings in the house in groups or individually, depending on their assignments to the 6 groups on the remote control transmitter, called “channels”.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS Setting the General Parameters ! When the batteries are first installed, REMOTE CONTROL SETTINGS MODE is activated directly: SET and YEAR appear on the screen, with the year flashing (this is the first parameter to be set). If there is no power supply for an extended period of time (batteries discharged or removed), the general parameters of the remote control transmitter will have to be reset. However, automatic commands remain stored in memory.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS Set the Following Parameters: STEP 1: YEAR (current year) STEP 2: MONTH (number of the current month) STEP 3: DAY (number of the current day) STEP 4/5: TIME (current time in hours and minutes) STEP 6: AREA (”US/EU” To automatically adjust for Daylight savings) STEP 7/8: JUNE (”Dusk/Twilight time” during midsummer, in hours and minutes) STEP 9/10: DEC (”Dusk/Twilight time” during midwinter, in December, in hours and minutes) ! The twilight times must be set between
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS Naming a Channel Channels Can Only be Named in MANUAL MODE STEP 1: The Telis 6 Chronis RTS must be in MANUAL MODE (if its in AUTOMATIC MODE, briefly press the SELECTION button ( ) to switch to MANUAL MODE). STEP 2: Select the channel you want to customize using the ARROW buttons or . STEP 3: Press and hold the SELECTION button ( ) until SET appears on the screen SET MODE is activated. The flashing hyphen corresponds to the character to be edited.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS Adding or Deleting Transmitter/Channel ! The procedure for assigning window coverings to the channels of the Telis 6 Chronis RTS and deleting them is identical. It can only be done in MANUAL MODE. STEP 1: Make sure that the Telis 6 Chronis RTS is in MANUAL MODE (if it is in AUTOMATIC MODE, briefly press the SELECTION button ( ) to switch to MANUAL MODE).
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS TILT MODE If the window coverings has tiltable slats (interior or exterior Venetian blinds, roller shutters with tiltable slats), SLAT ORIENTATION MODE can be configuration in EU or US MODE on each channel. For the motors of interior blinds, other than blinds with tiltable slats: blinds, roller shutters, screens, etc. it is recommended that the TILT MODE be configured in US MODE. BY default, all channels are configured in US MODE.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS Programming the days of the week The Telis 6 Chronis can automatically send orders to one or more groups of window coverings when it is in AUTOMATIC MODE, after creating a program. Up to 6 automatic commands any combination of the 6 can be programmed for each day of the week. Each of these Automatic Orders can be: 1. Set for a specific set time or a twilight/dusk 2.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS Editing an Automatic Order STEP 5: When EDIT flashes, briefly press the SELECTION button ( ) an AUTOMATIC ORDER flashes. Creating or Modifying an AUTOMATIC ORDER STEP 6: To create a new AUTOMATIC ORDER: select the blank order using the ARROW buttons or and go to step 7. (If 6 automatic orders have already been created, only one of these orders can be modified).
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS STEP 18: Briefly press the SELECTION button ( ) to confirm the order selected: the day concerned flashes. STEP 19: Press and hold the SELECTION button ( ) to exit SET MODE and return to AUTOMATIC MODE. -To modify another AUTOMATIC COMMAND, repeat the procedure starting at STEP 1.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS Copying the Program from One Day to Another When the program for one particular day is identical to that of another day of the week, the copy/paste function can be used to copy the entire program that has already been configured for one day and paste it to another day. STEP 1: Make sure that the Telis 6 Chronis RTS is in AUTOMATIC MODE (if is in MANUAL MODE, briefly press the SELECTION button ( ) to switch to AUTOMATIC MODE.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS Deleting an Automatic Command STEP 1: Make sure that the Telis 6 Chronis RTS is in AUTOMATIC MODE (if it is in MANUAL MODE, briefly press the SELECTION button ( ) to switch to AUTOMATIC MODE). STEP 2: Press and hold the SELECTION button until "SET" appears on the screen: AUTOMATIC COMMAND PROGRAMMING MODE is activated, and the day previously displayed flashes. STEP 3: Select the day you want to modify using the ARROW buttons or .
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS OPERATION IN USER MODE ! To switch from MANUAL to AUTOMATIC MODE, or AUTOMATIC to MANUAL MODE, briefly press the SELECTION button ( ). MANUAL MODE MANUAL MODE on the Telis 6 Chronis RTS is used to: -Send an occasional order to the window coverings assigned to the 6 different channels -Deactivate automatic command programming.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS AUTOMATIC MODE AUTOMATIC MODE on the Telis 6 Chronis RTS is used to: -Automatically control the window coverings assigned to the 6 different channels, using automatic commands programmed according to the days of the week. -Program the activation or deactivation of the SUN function, according to the channels. -Programming the automatic orders for each day of the week (see Programming the days of the week section).
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS VACATION MODE In AUTOMATIC MODE, the “VACATION MODE” function randomly changes the times at which the programmed automatic commands are sent, within a range of 0 to 30 minutes. This function is specially recommended to simulate your presence when you are away from home for an extended period of time.
QUICK PROGRAMMING FOR TELIS 6 CHRONIS RTS MANUAL MODE Short Press To switch from AUTO MODE to MANUAL MODE or from MANUAL MODE to AUTO MODE, pres the SELECTION button briefly 7 sec To access TILT MODE PROGRAMMING: Press the SELECTION button until the screen displays US 87 2 sec To access the MANUAL MODE and NAME THE CHANNELS Press the SELECTION button until the screen flashes and displays the word SET
AUTOMATIC MODE Short Press To switch from AUTO MODE to MANUAL MODE or from MANUAL MODE to AUTO MODE, pres the SELECTION button briefly 2 sec To access the AUTO MODE and SET TIMES RANGES Press the SELECTION button until the screen flashes and displays the word SET 7 sec To access the GENERAL MODE and SET THE GENERAL PARAMETERS Press the SELECTION button until the screen displays YEAR.
TROUBLESHOOTING RTS MOTORS BEFORE YOU CALL FOR SERVICE: Verify the motor is powered Verify the motor is installed correctly inside the tube (Crown & Drive correctly installed) Verify the motor limits are set correctly Allow time for motor to cool off after continuous operation (motors are equipped with a thermal shut off for safety) Verify the motor is not over loaded Verify all sensors on location are within RTS range and are working properly Check the transmitter batteries (LED should flash with a button
www.somfysystems.com Somfy Systems, Inc. North America Headquarters 121 Herrod Blvd Dayton, NJ 08810 (P) 800 43SOMFY (P) 609 395 1300 (F) 609 395 1776 Florida 6100 Broken Sound Pkwy Northwest Suite 14 Boca Raton, FL 33487 (P) 877 227 6639 (P) 561 995 8376 (F) 561 995 7502 © Copyright Somfy Systems, Inc.