Installation Manual MFSPOE-8 Network Switch
MFSPOE-8 Installation Manual ©2010-2014 Universal Remote Control, Inc. The information in this owner’s manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this owner’s manual may be subject to change without prior notice.
TABLE OF CONTENTS Introduction 1 Features 2 Parts Guide 2 Front Panel Description 3 Rear Panel Description 4 MFSPOE-8 Installation Considerations 5 Installation 6 MFSPOE-8 Installed in a Small System 6 MFSPOE-8 Installation Optimized for Max Number of PoE Ports 7 MFSPOE-8 Installed in the area with the Network Distribution 8 Frequently Asked Questions 9 Specifications 10 Limited Warranty Statement 11 End User Agreement 13 Federal Communication Commission Interference Statement 14
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Introduction The MFSPOE-8 Network switch is the ideal “Plug-n-Play” solution to supply power to Total Control Keypads and IP Cameras, while protecting network WAP’s (Wireless Access Points) from multicast audio streams. Total Control products, like the DMS-1200 (Multi-zone Amplifier), DMS-100 (Single-Zone Amplifier) and the SNP-1 (Streaming Network Player), all multicast audio streams onto the LAN.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Features u MAC filtering prevents multicast audio streams from consum- ing network bandwidth. u Smart PoE ports support keypads, IP cameras, etc.; also com- patible with non-PoE devices. u Eight (8) 10/100 Smart PoE (Power-Over-Ethernet) ports plus one LAN port. u Activity and Status LEDs, plus Connectivity indicator u Includes 48 volt power supply Parts Guide 1 1 1 1 1 1 – MFSPOE-8 MAC Filtering Switch with PoE – 1.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Front Panel Description Power LAN Connectivity Indicator Indicator PoE Port Status Indicators Power Indicator: Illuminates when the MFSPOE-8 Power Supply is connected to AC outlet. Ethernet Network Connectivity Indicator: Illuminates when the MFSPOE-8 is connected to a LAN and has received an IP Address. PoE Port Status Indicators: Illuminate when a PoE compliant device is connected to a port.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Rear Panel Description Power LAN Connection 4 Soft Rubber Non-Scuff Feet 8 - PoE 10/100 Smart Ports Removable Wall Bracket Mac Filtering Network Status Indicator LEDs Power: Provides connection to Included 48V Power Supply. LAN Connection: Provides connection to the LAN (Local Area Network).
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL MFSPOE-8 Installation Considerations Only one MAC Filtering switch should be used in a typical Total Control system. All streaming products like the DMS-1200, DMS100 and SNP-1 must be connected to the switch. Other Total Control devices that don’t stream (like the MRX-10 or the MRX-1) don’t have to be connected to the MFSPOE-8. You cannot daisy-chain MFSPOE-8 MAC Filtering switches; communication between switches will be blocked.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Installation 1. On the back of the MFSPOE-8, connect one end of a CAT5 cable to the port labeled LAN 10/100. 2. Connect the other end of the CAT5 cable to the LAN (Local Area Network). 3. Connect Total Control and standard network devices to any of the eight PoE 10/100 Smart Ports. 4. Connect the supplied 48V Power Supply to the MFSPOE-8 and then plug it into an unswitched AC outlet. 5. Once powered up, the unit begins working in approximately 30 seconds.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL MFSPOE-8 Installation Optimized for Max Number of PoE Ports Internet Cable Modem Wi-Fi Router wireless Access Point MFSPOE-8 MAC Filtering Switch Standard Network Switch MRX-10 Whole House Controller TKP-2000 TKP-100 MC 75 CD IP Camera 1 TKP-2000 TKP-100 MC 75 CD IP Camera 2 TKP-2000 SNP-1 Streaming Network Player DMS-1200 Digital Multi-Zone Amp Notes: n The Wireless Access Point CANNOT be connected to the MFSPOE-8; it must be connected to the Route
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL MFSPOE-8 Installed in the area with the Network Distribution Occasionally you get a retrofit installation where only one CAT5 wire has been run to a room, and there’s no way to run another one. In this case, locate the MFSPOE-8 in the Utility Room, Garage, or wherever the central distribution point for the Network is located and install standard network switches in rooms where you plan to locate a DMS-1200, DMS-100 or SNP-1.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Frequently Asked Questions Do I need to use a MFSPOE-8 in a Total Control system? If you are only controlling a Home Theater with a MRX-10, and there are no Total Control streaming sources like the DMS-1200 or DMS-100 in the system, then the answer is NO, you do not need to use a MFSPOE-8. If you have DMS-1200(s) or DMS-100(s) in the system, then the answer is YES, you must use a MFSPOE-8 or MFS8 in the system, connected to the those components.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Install the MFSPOE-8 in the room that contains the CAT5 distribution for the entire house. In the room where you plan to install the DMS-100, connect a standard network switch to the incoming CAT5, and then connect the DMS-100, PC and Printer to the switch. It is not recommended to connect PCs used for internet gaming to a MFSPOE-8, as this may affect the performance of video gaming during heavy stream usage.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Limited Warranty Statement 1. Limited Warranty and Disclaimers Universal Remote Control, Inc. (“URC”) warrants that the URC equipment shall be free from defects in material and workmanship under normal usage for two (2) years from purchase when such is purchased from URC. This limited warranty is valid only in the United States of America.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL SKILL AND CARE, OR OUTCOME OR RESULTS. WITHOUT IN ANY WAY LIMITING THE GENERALITY OF THE OTHER PROVISIONS HEREIN, WARRANTY DOES NOT COVER: (I) DAMAGE FROM MISUSE, NEGLECT OR ACTS OR NATURE, (II) MODIFICATIONS, (III) INTEGRATION WITH THIRD PARTY CONTENT (IV) BEYOND THE WARRANTY PERIOD AND/ OR FAILURE TO FOLLOW URC WARRANTY CLAIM PROCEDURE.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL URC’s PC programmable remotes or any of our Total Control® whole-house equipment are authorized for online internet sales. Buying URC’s PC programmable remotes or any of our Total Control® whole-house equipment online means buying equipment that does not have a URC’s limited warranty. Such equipment is not eligible for URC tech support or software support, either. 2.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Regulatory Information to the user n CE conformity Notice Products with “CE” marking comply EMC Directive 2004/108/EC issuedby the commission of the European Community. 1) EMC Directive lEmission lImmunity lPower : EN 55022 : EN 55024 : EN-61000-3-2, 3 n Declaration of Conformity “Hereby, Universal Remote Control Inc. declares that this MFSPOE-8 is in compliance with the Essential requirements and other relevant provisions of EMC Directive 2004/108/EC.
MFSPOE-8 NETWORK SWITCH INSTALLATION MANUAL Declaration of Conformity Company Name : Universal Remote Control Inc. Company Address : Contact Info rmation : Brand Name : 500Mamaroneck Avenue, Harrison, NY 10528, U.S.A www.universalremote.
NOTE Page 17
NOTE Page 18
NOTE Page 19
NOTE Page 20
500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 www.universalremote.
