FOR REFERENCE ONLY 42″ HD Gas Plasma Display Technical Manual www.rosenaviation.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Table of Contents INTRODUCTION ................................................................................................................................................ 3 SAFETY.............................................................................................................................................................. 4 GENERAL SAFETY ...............................................................................................
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Instant On .................................................................................................................................................. 16 OSD Background....................................................................................................................................... 16 Freeze.......................................................................................................................................
2” HD Gas Plasma Display Rosen Aviation Displays, LLC Introduction Congratulations! You have purchased the world’s most advanced and highest resolution 42" HD gas plasma display with built-in motion adaptive line doubler/scalar and multiple high definition television (HDTV) direct inputs. You have wisely invested by choosing to use a digital plasma display. In addition, there are up to 8 video inputs and multiple picture-in-picture (PIP) scenarios.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Safety General Safety Caution Use the three-prong AC power cord supplied with the unit to ensure that proper ground connection is maintained. A safety ground lug is also provided on the unit and should be used in accordance with your local electrical code. Failure to provide a proper ground from the installation’s power source may result in injury to personnel and serious damage to the unit that would not be covered under warranty.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Getting Started Unpacking Caution Extreme caution should be taken when unpacking the digital monitor. It has been designed for rugged use; however the display monitor contains glass that could break if dropped. Appendix A (page 20) shows how the 42" HD gas plasma display was packaged for shipment. This will guide your efforts to unpack the system. Carefully remove all components of the display from the packaging.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Installation and Connection Installation Warnings The display unit shall be handled by at least two persons during installation and moving. The display should be operated only when proper connection has been made to the grounding stud provided on the unit. Mounting the unit in any orientation with installer/user supplied mounting hardware is totally the installer/user’s responsibility and liability. Removal of the front bezel is strictly prohibited.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Operator Interface Connections All operator connectors are located at the rear of the unit. Only one video source is required for your new 42" HD gas plasma display. However, multiple video sources can be connected at the same time. IR Code Switch Fuse Carrier Video Bundle Ground Stud Figure 2 Up to 8 Video Inputs: INPUT DVI RGB CONNECTOR TYPE DVI 1.0 DVI 1.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC DVI (Digital Visual Interface) If your new display is being used with a computer with DVI output, connect a DVI cable to this connector location and the other end to your computer. Your cable should not be longer than necessary.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC S-Video and S-Video.A If the display is to be used with a video source that uses the S-Video type of interconnection, connect the 4-pin mini-DIN connector to this connector location, or to the video bundle’s S-Video.A 4-pin mini-DIN connection (see video bundle in Figure 5). This cable should not be longer than necessary. Figure 5 Composite Video NOTE: A Source cannot be selected from the OSD unless it has been enabled and saved.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Input Power and Ground Connections Caution Ensure that the AC power cord is disconnected from the AC power source before performing the following steps. Ground Stud Connections The back of the display has a ground stud that must be connected to an earth ground (see Figure 2 on page 7).
42” HD Gas Plasma Display Rosen Aviation Displays, LLC IR Sensor Figure 6 Unit Operation After the installation is complete, plug the main power cord into the specified voltage outlet. The unit has been set up at the factory so that it will turn on in the standby mode. Remote Power On/Off The remote control has a function that will only enable and disable the display’s screen (for example: standby mode). The unit will remain in the standby mode when the display screen is disabled by remote control.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC as factory default discrete command button 9. The user can immediately recall the discrete command button assignments by pushing 9 on the IR. Note: This assumes that the user has not changed this particular factory default. Analog RGB/DVI Modes Once the VGA/SVGA mode is invoked by selecting the VGA source, menu selections are available for adjusting color, contrast, brightness and interface synchronization as well as FlexiScreenTM control.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Display Aspect Ratio Selections “16:9“ will cause the image to fill the entire width of the display screen. “4:3” will cause the image to only fill a portion of the display screen to achieve a 4:3 aspect ratio. “1:1” (not shown below) will cause the image to fill the screen with a direct one for one pixel association with the source aperture adjustments.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Source Aperture Adjustments Although the Source Aperture Selection initializes the source aperture, the FlexiScreenTM menu also includes provisions for manual adjustments. Height and width along with the horizontal and vertical offsets are provided to allow the user ultimate control. These settings define the boundaries of the active image showing on the display.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC program or vice versa. These programs can be swapped or toggled from one to the other using the remote control system or the IR (remote control: factory default direct IR command button 8). Note: Figure 2 (page 7) indicates there are certain exclusions to the multiple scenario PIPs. For example, 2 video inputs sharing the same switch cannot be combined in a PIP scenario.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Instant On This setup option enables the display to turn on and show video as soon as the power is applied to the unit. If set to OFF, this option keeps the unit in the standby mode until the user enables the display via the IR remote or the RS232 control. OSD Background When enabled, the OSD will have a solid background. If disabled, the OSD will not have a distinctive background.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Care and Maintenance Caution Do not allow water or other liquids to enter the unit. This can cause serious damage to the unit that would be very costly to repair. Always be sure that the AC power is turned off during cleaning. Screen Cleaning The screen can be cleaned using a very mild glass cleaner that is non-abrasive, and a lens grade tissue for optical surfaces. Do not spray the glass cleaner directly onto the glass.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Operator Troubleshooting Category Power Symptom Unit does not come on Unit comes on but display does not light or have O.S.D. 1. Batteries in remote 2. Remote power on Remote does not work or unit will not turn on with infrared remote control Display turns on with O.S.D.
42” HD Gas Plasma Display Category DVI, Analog RGB Mode Rosen Aviation Displays, LLC Symptom Screen does not sync up Blue is dim or too bright Green is dim or too bright Red is dim or too bright Composite Video, S video and YPbPr.1 Component Video YPbPr.2 1. Input settings for the computer. They should be one of the acceptable display rates listed in Appendix D (page 38) 1. O.S.D. Blue Gain Adjustment 1. O.S.D. Green Gain Adjustment 1. O.S.D.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX A: PACKING FOR SHIPMENT Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Shipping Procedure for 42" HD Gas Plasma Display In the event that the 42” display needs to be shipped, the following procedures must be followed to protect it from damage. Rosen Aviation Displays, LLC is NOT Responsible for damage to equipment not packaged according to the guidelines listed below.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX A: PACKING FOR SHIPMENT Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Notch Notch Figure A.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX B: REMOTE CONTROL OPERATION OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual The standard remote control system for the 42" HD gas plasma display is described in this appendix. The standard system has many user settings, which can be saved to non-volatile system memory for the user’s convenience. This allows the user to set up the system once and restore their settings after the power has been shut off.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX B: REMOTE CONTROL OPERATION OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual SL8000 Home Theater Remote Control To Program the Remote control for operation with the 42HD Video Display, follow the steps below. 1. 2. Press and hold the TV and the Mute buttons at the same time until the display on the remote control say SET. Enter in one of the following codes. IR Code Switch Setting 1 2 3 3.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX B: REMOTE CONTROL OPERATION OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual IR Remote Control Keycodes Keycodes correspond to NEC IR protocol Only the codes to which the display responds are listed Program Code corresponds to the One For All, RCA or Allegro programming code Names next to the program code are manufacturers which commonly use this code set IR REMOTE SELECT SWITCH DOWN (1) IR REMOTE SEL
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX B: REMOTE CONTROL OPERATION OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Menus and RS232 Commands for the HD Digital Video Controller General Description The extensive menu and RS232 control system that has been built into the HD digital video controller (HD DVC) has been designed for simple navigation, user friendliness, and application diversity.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX B: REMOTE CONTROL OPERATION OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual RS232 Control The following chart describes the RS232 commands. The commands must be followed by a carriage return . Some commands require values to be entered such as Brightness. These values are to be entered in as hexadecimal ASCII with leading zeros when necessary.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX B: REMOTE CONTROL OPERATION OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Main Display Commands Source Selection SYNTAX srcX Brightness Contrast Hue Color Saturation Red Magnitude For RGB Inputs Blue Magnitude For RGB Inputs Green Magnitude For RGB Inputs Sharpness, Fine Sharpness, Coarse Panel Brightness Input Color Space Selection Input Select Notification brtXX conXX hueXX satXX re
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX B: REMOTE CONTROL OPERATION OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual PIP COMMANDS SYNTAX PIP Window Enable Toggle PIP Window Enable PIP Source Selection pip pipX psrcX PIP Side By Side Enable PIP Swap With Main Image Pip Input Color Space Selection pssX pswp pcscX OSM COMMANDS OSM Ctrl: UP OSM Ctrl: DOWN OSM Ctrl: RIGHT OSM Ctrl: LEFT OSM Display/Hide Toggle Refresh OSD Os
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX B: REMOTE CONTROL OPERATION OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Outline Drawing, RJ45 to Sub D RS232 cable Front View Front View 25 feet RJ45 1 2 3 4 5 6 7 8 COLOR Blue Blue/white Orange Orange/white Green Green/white Brown Brown/white Recommended Parts QTY MANUFACTURER 1 1 1 25 ft Amp Amp Amp Belden DESCRIPTION DSR (in) DTR (out) RD (data in) GND TD (data out) GND CTS (in) RTS (out) No con
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX C: OSD MENU STRUCTURE & COMMANDS Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Composite.Y Menu This menu is for Composite.Y input. It is the yellow RCA female connector in the video bundle, thereby the “Y”. “NONE” in the top line could be replaced with NTSC or PAL, dependant on the received signal from the composite signal’s connected source.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX C: OSD MENU STRUCTURE & COMMANDS Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Composite Source Setup menu This menu is common to all composite sources. Any changes here will vary the input source settings for all composite inputs. The active menu items are brightness, contrast, hue, color, and sharpness. The CAV items are for a different input. Do not adjust the CAV items while in the composite mode.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX C: OSD MENU STRUCTURE & COMMANDS Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Digital DVI Menu The digital DVI input is the highest quality input available. The reason for this quality is that the video signal is not an analog signal, which requires conversion to digital.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX C: OSD MENU STRUCTURE & COMMANDS Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Analog RGB Source Setup Menu In the analog RGB mode, the HD DVC assigns the source setup values and it is not recommended that the application change these settings. However, the application can change them to provide for a shift in the display as necessary. Use the up or down arrows to select and change settings from the factory default.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX C: OSD MENU STRUCTURE & COMMANDS Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual YPbPr.2 Menu The YPbPr.2 input uses the 3 BNC-style connector on the HD DVC. You can supply a signal from 480p or 720p including 540p on this input. This input will not accept the interlaced style input such as 1080i. “None” on the menu’s first line will be replaced by the resolution that has been detected.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX C: OSD MENU STRUCTURE & COMMANDS Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual PIP Control Menu The Picture in Picture (PIP) control menu allows full flexibility in viewing 2 sources at the same time. Keep in mind some limitations were noted under PIP Modes in the main text. Choose a viewing source, such as S-Video, and then move to enable and turn it on. The PIP window appears.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX C: OSD MENU STRUCTURE & COMMANDS Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Display Setup Menu Use the display setup menu to customize the way the display system functions. FREEZE, INSTANT ON, and OSD BACKGROUND can either be set to ON or OFF. RESTORE FACTORY SETTINGS: All parameters stored in the unit will be replaced, and any setup that has been saved will be erased and replaced.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX C: OSD MENU STRUCTURE & COMMANDS Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Direct IR Setup Menu Use this menu to setup one touch direct access to a menu, or selection of an input, or discrete power on/off. Each of the number keys, (0–9) can be set to do any function listed below left. These functions make it easier for the application to switch functions without going through the menus.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX D: CONFIGURATION AND PERFORMANCE OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Specifications Screen Size 42” diagonal; 36.3” (w) x 20.6” (h) Resolution 1024(h) x 1024(v) color pixels Size 39.5”(w) x 23.8”(h) x 3.25”(d) Pixel pitch 0.90mm x 0.51mm Viewing Angle 160 degrees omnidirectional Color Depth 16.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX D: CONFIGURATION AND PERFORMANCE OVERVIEW Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual Mechanical All metal packaging Textured black exterior paint Notes to Specifications: Corrosive Environments: Non-operating unit exteriors – do not expose for prolonged periods to ocean spray, rain or moisture. Unit interiors – do not allow water or other liquids inside the units under any conditions.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC APPENDIX E: Definition of Terms Rosen Aviation Displays, LLC, 42" HD Gas Plasma Display Technical Manual HD HDTV DVD OSD IR PIP RGBHV VESA HD-DSS FCC CE CSA UL DVI VGA YPrPb CAV High Definition High Definition Television Digital Versatile Disk On Screen Display Infrared Universal Remote Control Picture In Picture Red Green Blue Horizontal Vertical Video Electronics Standards Association High Definition Digital Satellite Service Federal Communications
” HD Gas Plasma Display Rosen Aviation Displays, LLC WARRANTY EXCLUSIONS No other warranty is expressed or implied, as to the product purchased, and under no circumstances shall the manufacturer or manufacturer’s representatives be liable for any liability, claim, loss, damage, expense or injury of any nature, or any direct, indirect, special, incidental, or consequential damages however caused and on any theory of liability in connection with or resulting from the resale or use of the products.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC OUTLINE DRAWINGS Scope The following drawing established the package outline of the 42” HD Gas Plasma Display. General Interpret this drawing in accordance with MIL-STD-100. All dimensions are in inches followed by the equivalent in millimeters placed in brackets [mm]. Do not scale this drawing.
42” HD Gas Plasma Display Rosen Aviation Displays, LLC 43
42” HD Gas Plasma Display Rosen Aviation Displays, LLC J2 is not used 44
42” HD Gas Plasma Display Rosen Aviation Displays, LLC Rosen Aviation Displays, LLC www.rosenaviation.com PH: (888) 668-4955 Thank you for your order www.rosenaviation.