Installation Manual MFS-8 Network Switch
MFS-8 Installation Manual ©2010-2014 Universal Remote Control, Inc. The information in this owner’s manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this owner’s manual may be subject to change without prior notice.
TABLE OF CONTENTS Introduction 1 Features and Benefits 1 Parts Guide 1 Front Panel Descriptions 2 Rear Panel Descriptions 3 MFS-8 Installation Considerations 4 MFS-8 Installed in a Small System 5 MFS-8 Installed in a Large System 6 MFS-8 Installed in the area with the Network Distribution 7 Frequently Asked Questions 8 Specifications 8 Limited Warranty Statement 9 End User Agreement 11 Federal Communication Commission Interference Statement 12 Regulatory Information to the user
MFS-8 NETWORK SWITCH INSTALLATION MANUAL Introduction The MFS-8 Network switch is the ideal "Plug-n-Play" solution to protect network WAPs (Wireless Access Points) from multicast audio streams. Total Control products, like the DMS-1200 (Multi-zone Amplifier), DMS-100 (Single-Zone Amplifier) and the SNP-1 (Streaming Network Player), all multicast audio streams onto the LAN. The nature of a "multicast" will shut down all wireless access to the network.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL Front Panel Descriptions Power Indicator LAN Connectivity Indicator Power Indicator: Illuminates when the MFS-8 Power Supply is connected to AC outlet. Ethernet Network Connectivity Indicator: Illuminates when the MFS-8 is connected to a LAN and has received an IP Address.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL Rear Panel Descriptions Power Soft Rubber Non-Scuff Feet LAN connection 8-10/100 Ports Removable Wall Bracket Mac Filtering Network Status Indicator LEDs Power: Provides connection to included 12V Power Supply. LAN Connection: Provides connection to the LAN (Local Area Network). 10/100 Ports: 8 - 10/100 Ports provide network connectivity to Total Control streaming products like the DMS-1200, DMS-100 and SNP-1.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL MFS-8 Installation Considerations Only one MAC Filtering switch should be used in a typical Total Control system. All streaming products like the DMS-1200, DMS100 and SNP-1 must be connected to the switch. You cannot daisy-chain MFS-8 MAC Filtering switches; communication between switches will be blocked.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL MFS-8 Installed in a Small System Internet Cable Modem Wireless Access Point Wi-Fi Router MFS-8 PSX-2 MRX-10 SNP-1 DMS-1200 Standard PoE Switch TKP-2000 TKP-2000 TKP-100 TKP-100 MC 75 CD IP Camera 1 MC 75 CD IP Camera 2 Notes: n The Wireless Access Point CANNOT be connected to the MFS-8; it must be connected to the Router in the LAN.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL MFS-8 Installed in a Large System Internet Cable Modem wireless Access Point Wi-Fi Router Standard Network Switch MFS-8 PSX-2 MRX-10 SNP-1 DMS-100 DMS-1200 Standard PoE Switch TKP-2000 TKP-2000 TKP-100 TKP-100 MC 75 CD IP Camera 1 MC 75 CD IP Camera 2 Notes: n The Wireless Access Point CANNOT be connected to the MFS-8; it must be connected to the Router in the LAN (Local Area Network).
MFS-8 NETWORK SWITCH INSTALLATION MANUAL MFS-8 Installed in the area with the Network Distribution Occasionally you get a retrofit installation where only one CAT5 wire has been run to a room, and there's no way to run another one. In this case, locate the MFS-8 in the Utility Room, Garage, or where ever the central distribution point for the Network is located, and install standard network switches in rooms where you plan to locate a DMS-1200, DMS-100 or SNP-1.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL Frequently Asked Questions 1. Do I need to use a MFS-8 in a Total Control system? If you are only controlling a Home Theater with a MRX-10, and there are no Total Control streaming sources like the DMS-1200 or DMS-100 in the system, then the answer is NO, you do not need to use a MFS-8. If you have DMS-1200(s) or DMS-100(s) in the system, then the answer is YES, you must use a MFS-8 in the system, connected to those components. 2.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL Limited Warranty Statement 1. Limited Warranty and Disclaimers Universal Remote Control, Inc. (“URC”) warrants that the URC equipment shall be free from defects in material and workmanship under normal usage for two (2) years from purchase when such is purchased from URC. This limited warranty is valid only in the United States of America.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL SKILL AND CARE, OR OUTCOME OR RESULTS. WITHOUT IN ANY WAY LIMITING THE GENERALITY OF THE OTHER PROVISIONS HEREIN, WARRANTY DOES NOT COVER: (I) DAMAGE FROM MISUSE, NEGLECT OR ACTS OR NATURE, (II) MODIFICATIONS, (III) INTEGRATION WITH THIRD PARTY CONTENT (IV) BEYOND THE WARRANTY PERIOD AND/ OR FAILURE TO FOLLOW URC WARRANTY CLAIM PROCEDURE.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL URC’s PC programmable remotes or any of our Total Control® whole-house equipment are authorized for online internet sales. Buying URC’s PC programmable remotes or any of our Total Control® whole-house equipment online means buying equipment that does not have a URC’s limited warranty. Such equipment is not eligible for URC tech support or software support, either. 2.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL Regulatory Information to the user n CE conformity Notice Products with “CE” marking comply EMC Directive 2004/108/EC issued by the commission of the European Community. 1) EMC Directive lEmission lImmunity lPower : EN 55022 : EN 55024 : EN-61000-3-2, 3 n Declaration of Conformity “Hereby, Universal Remote Control Inc. declares that this MFS-8 is in compliance with the Essential requirements and other relevant provisions of EMC Directive 2004/108/EC.
MFS-8 NETWORK SWITCH INSTALLATION MANUAL Declaration of Conformity Company Name : Universal Remote Control Inc. Company Address : 500Mamaroneck Avenue, Harrison, NY 10528, U.S.A www.universalremote.
NOTE Page 15
NOTE Page 16
500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 www.universalremote.