R UL-801 Installation Manual The information contained herein is subject to the Export Administration Regulation (“EAR”), 15 C.F.R. Parts 730-774. Diversion contrary to U.S. law is prohibited. This publication is available at www.uasc.com.
UL-801 Installation Manual Record of Revisions Rev No. Issue Date Insertion Date Initials UASC Retain this record in front of the manual. Upon receipt of revision, insert and remove pages according to the List of Effective Pages. Then enter on this page the revision number, issue date, insertion date and your initials.
UL-801 Installation Manual Record of Temporary Changes Change No. Page No. Issue Date Insertion Date & Initials Removal Date/Initials/Reason Retain this record in the front of this manual. Upon receipt of a Temporary Change, insert pages into manual and enter the Temporary Change number, page number, issue date, insertion date and your initials. Also, record the removal of each temporary change.
UL-801 Installation Manual Record of Temporary Changes (Continued) Change No. Page No. Issue Date Insertion Date & Initials Removal Date/Initials/Reason Retain this record in the front of this manual. Upon receipt of a Temporary Change, insert pages into manual and enter the Temporary Change number, page number, issue date, insertion date and your initials. Also, record the removal of each temporary change.
UL-801 Installation Manual List of Effective Pages Subject Page Date Page Date 25 26 27 28 29 30 31 32 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 FAA Approval 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 Equipment Specifications 201 202
UL-801 Installation Manual Subject System Data Installation Page Date 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 20
UL-801 Installation Manual Subject Page Date 508 509 510 511 512 513 514 515 516 517 518 519 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 Appendix 1 A1-1 A1-2 A1-3 A1-4 A1-5 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 Appendix 2 A2-1 A2-2 A2-3 A2-4 A2-5 A2-6 A2-7 A2-8 A2-9 A2-10 A2-11 A2-12 A2-13 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 Dec 2011 15 De
UL-801 Installation Manual Table of Contents Record of Revisions ............................................................................................................. 1 Record of Temporary Revisions ........................................................................................... 1 List of Effective Pages .......................................................................................................... 1 Table of Contents ...........................................................
UL-801 Installation Manual FAA Approval .................................................................................................................... 101 1. General................................................................................................................... 101 A. Applicable TSOs .............................................................................................. 101 B. TSO Deviations .....................................................................................
UL-801 Installation Manual R. UL-801 to MFD-640 – High Resolution (MFD SCN 1011.4.8 or later) ............. 333 S. UL-801 to Remote CDU (RCDU) - Low Resolution ......................................... 334 T. UL-801 to MFD-640 – Low Resolution (MFD SCN 1011.4.7 or earlier) ........... 335 U. UL-801 to CVR/CVFDR ................................................................................... 336 V. UL-801 to DTU-100 .........................................................................................
UL-801 Installation Manual E. F. G. H. I. J. K. L. Device Status ................................................................................................... 502 UniLink to Display Processor RS-422 Communications................................... 502 UL-801 VHF Communications ......................................................................... 503 OOOI Sensor Test ........................................................................................... 503 Printer Test ......................
UL-801 Installation Manual Introduction 1. Makeup and Use of This Manual A. Application This manual provides installation information pertaining to the UL-801. B. Organization This manual provides information about: • Description of the components of the UL-801 • Environmental qualification forms • UniLink equipment specifications • Installation and wiring requirements • Worksheets and procedures for installing system data including configuring the UL-801 Configuration Module 2.
UL-801 Installation Manual Description and Operation 1. Description The UL-801 Airborne Datalink provides an air-to-ground two-way digital datalink that meets the need for specific air-to-ground communications. UniLink communicates with multiple ground-based Datalink Service Providers (DSP) using a VHF radio and/or SatCom telephony-based system. The UL-801 contains an internal VHF Data Radio (VDR). NOTE: Both DSP and DLSP are used as acronyms for Datalink Service Providers.
UL-801 Installation Manual The communication links used to exchange data are Very High Frequency (VHF), including: • The legacy Aircraft Communications Addressing and Reporting system (ACARS) • Next-generation VHF digital link (VDL) Mode 2 • Satellite Communications (SatCom).
UL-801 Installation Manual SatCom weather graphic uplinks via circuit mode data and text weather uplinks via Short Burst Data (SBD) or packet data mode may or may not be available, based on your selected DSP and the SatCom equipment installed. In addition, some functions/features may only be available through specific communications systems as described in the following table.
UL-801 Installation Manual FANS-1 is the original version of FANS developed by Boeing and FANS-A is the corresponding version developed by Airbus. Both of these versions are interoperable with worldwide ATC facilities and use the Aircraft Communications Addressing and Reporting System (ACARS) network. UniLink’s FANS-1/A+ implementation is designated as such because it is functionally equivalent to, and combines many of the best features of both Boeing’s FANS-1 and Airbus’ FANS-A implementations.
UL-801 Installation Manual Hardware/Software Compatibility The hardware versions are made available to the application software and are verified for compatibility during power-up checks and during application software loading. Restricted Access to the Field-Loading Function The field-loading function is only enabled when the aircraft is on the ground and after a password has been entered successfully.
UL-801 Installation Manual The Customer Database (CDB)-driven user interface and message set can be customized to match airline or business operator’s operational requirements. Each database is described below. • • • Customer Database Contains screen and message definitions for Aeronautical Operational Communications (AOC) and Air Traffic Services (ATS) applications.
UL-801 Installation Manual F. UASC FMS Interface The UniLink provides concurrent user interface access for up to three UASC Flight Management Systems. The ARINC 429 interface uses the ARINC 739 protocol for display control and ARINC 619 bit oriented file transfer protocol for file exchange between the devices. Each UASC FMS provides a high-speed ARINC 429 channel as inputs to UniLink. The specific channel will be specified by the configuration module, based on aircraft wiring.
UL-801 Installation Manual (1) UniLink interface capabilities SATCOM-BASED AIRBORNE TELEPHONY VHF ANTENNA AIRBORNE TELEPHONE SYSTEMS IRIDIUM/INMARSAT SATCOM RS-232 A741 10 DISCRETE INPUT DEVICES 14 DISCRETE OUTPUT DEVICES A741 OPEN/ GROUND OPEN/ GROUND A739 MCDU A739 MCDU A739 MCDU UNILINK UL-801 ARINC A429 A429 CONFIGURATION MODULE UNIVERSAL AVIONICS FLIGHT MANAGEMENT SYSTEMS SUPPORTS UP TO 3 UASC FMSs OR ARINC 702A FMC STANDARD ETHERNET SOLID STATE DATA TRANSFER UNIT (SSDTU) * RS-422 GRAP
UL-801 Installation Manual (2) UL-801 to UNS-1E/UNS-1C+ Block Diagram – non FANS-enabled UNS-1E/UNS-1C+ #1 UNS-1E/UNS-1C+ #2 UNIVERSAL UNIVERSAL DA NA VN DT LI PR 1 2 3 FU F PE TU MEN NE 4 5 6 7 8 9 BA 0 MS ON/ OFF ± A B C D E F G H I J K L M N O P Q R S T U V W X Y Z DA NA VN DT LI PR 1 2 3 FU F PE TU MEN NE 4 5 6 7 8 9 BA 0 MS ON/ OFF ± A B C D E F G H I J K L M N O P Q R S T ENT U V W X Y Z ENT ARINC 429 LS ARINC 429 HS ARINC 429 HS RS-422
UL-801 Installation Manual (3) UL-801 to UNS-1Esp/UNS-1Csp+ Block Diagram – non FANS-enabled UNS-1Esp/ UNS-1Csp+ #1 UNS-1Esp/ UNS-1Csp+ #2 UNIVERSAL UNIVERSAL DA NA VN DT LI PR 1 2 3 FU F PE TU MEN NE 4 5 6 7 8 9 BA 0 MS ON/ OFF ± A B C D E F G H I J K L M N O P Q R S T U V W X Y Z DA NA VN DT LI PR 1 2 FU F PE TU MEN NE 4 5 7 8 9 BA 0 MS ON/ OFF ± A B C D E F G H I J K L M N O P Q R S T ENT U V W X Y Z 3 6 ENT ARINC 429 LS ARINC 429 HS ARINC 42
UL-801 Installation Manual (4) UL-801 to UNS-1F/UNS-1D+ Block Diagram – non FANS-enabled 4/5" FPCDU UNIVERSAL DA NA VN DT LI PR 1 2 3 FU F PE TU MEN NE 4 5 6 7 8 9 BA 0 MS ON/ OFF ± A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 4/5" FPCDU UNIVERSAL DA NA VN DT LI PR FU F PE TU MEN NE A B C D E F G H I J K L M N O P Q R S T ENT U V W X Y Z 1 2 4 5 7 8 9 0 MS BA ON/ OFF ± 3 6 ENT NCU #2 UNS-1F/UNS-1D+ NCU #1 UNS-1F/UNS-1D+ UNI UNI ARINC
UL-801 Installation Manual (5) UL-801 to UNS-1L/UNS-1K+ Block Diagram – non FANS-enabled UNIVERSAL UNIVERSAL MSG NA MSG NA DAT DT DAT FUE FP FUE FP TUN VNA TUN VNA PRE LI PRE MENU NEX PER PWR DIM NEX PWR DIM 1 2 3 H I J K L M N 4 5 6 O P Q R S T U 7 8 9 ENTE BACK 0 V W X Y Z A B C D E F G DT LI 1 2 3 H I J K L M N 4 5 6 O P Q R S T U 7 8 9 ENTE BACK 0 V W X Y Z A B C D E F G MENU PER 4 FPCDU 4 FPCDU NCU #2 UNS-1L/UNS-1K+ NCU #1 UNS-1L/UNS-1K+ UNI UNI ARIN
UL-801 Installation Manual (6) UL-801 to UNS-1Ew Block Diagram - FANS-enabled (FMS SCN 1000.5/1100.
UL-801 Installation Manual (7) UL-801 to UNS-1Espw Block Diagram - FANS-enabled (FMS SCN 1000.5/1100.
UL-801 Installation Manual (8) UL-801 to UNS-1Fw Block Diagram - FANS-enabled (FMS SCN 1000.5/1100.
UL-801 Installation Manual (9) UL-801 to UNS-1Lw Block Diagram - FANS-enabled (FMS SCN 1000.5/1100.
UL-801 Installation Manual G. Configuration Module The configuration module, an electrically erasable, programmable read-only memory (EEPROM) device, is mounted on the rear of the mounting tray and connected via a dedicated interface to the UniLink. The configuration module stores information specific to the installation. The user can view and retrieve the aircraft configuration through specially designed pages that can be accessed through the keypad on the CDU or MCDU.
UL-801 Installation Manual Device UniLink TX Speed (NOTE 1) UniLink RX Speed Test Device (NOTE 3) LOW or HIGH HIGH ARINC 743A GNSS Receiver Not Applicable HIGH or LOW (NOTE 4) DADC1 Not Applicable HIGH or LOW (NOTE 5) DADC2 Not Applicable HIGH or LOW (NOTE 5) Generic 429 Device (1 – 4) LOW or HIGH NOTE 2 757 CVR HIGH HIGH Not Applicable Device TX speed supported by UniLink. The customer database specifies the data speed of this configurable device.
UL-801 Installation Manual J. Discrete Inputs/Outputs UniLink provides 10 general purpose discrete input connections and 14 general purpose discrete output connections. Discrete Inputs 5 VDC 3.3 VDC DISCRETE INPUT NOTE: THE TRANSITION VOLTAGE VALUE IS 3.8 VDC. THE ABOVE CIRCUIT IS INTERNAL TO UNLINK.
UL-801 Installation Manual Door n Closed Door n Closed Options Active State NOTE: Active Inactive Ground Door n is closed Door n is open Open Door n is closed Door n is open If more than one door discrete input is wired and configured, the inputs are logically AND’ed together by UniLink to determine approximately when "all doors are closed". Discrete Outputs UniLink provides 14 discrete outputs.
UL-801 Installation Manual FANS Aural (when FANS is enabled) FANS Aural Active State Active Ground (Recommended Configuration) Open FANS alerter on FANS ATC annunciator off FANS alerter off FANS ATC annunciator on NOTE: Inactive The aural alerting devices must be connected to the aircraft 28 VDC power. CPDLC Connect CPDLC Connect Active State NOTE: Active Ground CPDLC connection active Open No CPDLC connection Use of this discrete is optional.
UL-801 Installation Manual K. Ethernet The UASC DTU-100/SSDTU physical interface is 10BaseT Ethernet. The UniLink hardware contains a 10/100BaseT Ethernet port. All UniLink interfaces to the UASC DTU-100 can be directly applied to the UASC SSDTU without any modifications to the UniLink. L. Transmission Media Management UniLink is capable of managing multiple links (VHF, TEL, and SAT) so that simultaneous transmission and receipt of messages is possible on several different links.
UL-801 Installation Manual M. VHF Management The UniLink contains an internal VHF radio for its data communication. UniLink will only attempt to transmit if the radio has successfully tuned to the selected frequency.
UL-801 Installation Manual N. SatCom-based Airborne Telephony (TEL) A dedicated standard telephone modem is designed into UniLink. This modem is used to transfer data between a supported ground station and the aircraft subsystems. For example, the airborne telephone modem is initially used for uploading messages, text weather, and graphical weather data from a DSP via a dial-up connection. UniLink manages only one RS-232 port for this use.
UL-801 Installation Manual Up to four low-resolution display devices can be connected to a single low-resolution bus and one high-resolution device each can be connected to two high-resolution graphic ports. TEL Media Status Reason COMM/MDM TIMEOUT UniLink has dialed the phone but a timeout occurred prior to a connection being established. NOTE: Sequential, excessive timeouts will result in the NOCOMM/AUTO DELAY message displaying.
UL-801 Installation Manual O. SatCom-based ARINC 741 (SAT) UniLink interfaces with an ARINC 741-capable SatCom system, such as the Universal/Thrane & Thrane Aero-I SDU and others, via a low speed ARINC 429 interface. Packet Mode ACARS data (Data 2) is sent to the SDU for forwarding to the ACARS gateway on the ground through the Ground Earth Station (GES) and vice versa. NOTE: The UASC Aero-I SatCom system is not approved for FANS messaging.
UL-801 Installation Manual Graphical Weather Depiction UniLink provides configurable graphic ports which can be configured to interface with a total of six graphics buses. Graphical weather information is available only when the UniLink is interfaced to a SatCom system via the RS-232 connection and supported by the DSP. The tip and ring data interface, available on previous UniLink models, is no longer required and therefore has been removed.
UL-801 Installation Manual DSP which then sends the uplink messages to a designated UniLink system or aircraft. The message is then processed by UniLink or, when the message is meant for a peripheral unit, is passed on to the appropriate peripheral unit. (1) (2) (3) (4) (5) ACARS Uplink Message Receiving When UniLink receives an uplink message from the ground system, it performs a Block Check Sequence (BCS) error check.
UL-801 Installation Manual Q. Advisory Alerts, Device Status, and Error Messages UniLink generates advisory alerts annunciating normal and non-normal conditions that require crew action. Selecting the advisory alert displays the UniLink page on which the corresponding information is displayed or from which a required action may be performed. Examples of advisories are: NEW MSG, VHF VOICE, NOCOMM, and NEW WX MAP.
UL-801 Installation Manual UniLink supports transmission of datalink message recordings to any ARINC Characteristic 757 CVR/CVFDR.
UL-801 Installation Manual T. Transmission Media Interfaces - Configuration Option SatCom is supported with a configurable interface to an A741 SDU for text-based messages. Telephony is supported with a configurable RS-232 interface to a UASC T-T Aero-M or Iridium systems for both text-based messages and graphical weather maps. MagnaStar and UASC Aero-I tip/ring telephony interfaces are not supported.
UL-801 Installation Manual Y. Flight Leg Transition The Flight Leg Transition feature is provided to reduce the crew workload (such as initializing the Origin of the next flight leg to the Destination of the flight leg that was just completed). It is also used as a means of automatically logging data from a flight leg that was just completed if that data may be needed for future reference, such as OOOI times and fuel. Z.
UL-801 Installation Manual FAA Approval 1. General Installation approval of the UniLink system is being accomplished under a variety of STCs and Forms 337. For a new installation to be eligible for approval, it will be necessary to apply to the FAA for an STC or to utilize an existing STC or Form 337.
UL-801 Installation Manual C. Equipment Classes Equipment Classes • UL-801, SCN 30: − F VDL Mode 2 receiver used in a 25-kHz channel separation environment − 7 VDL Mode 2 transmitter used in a 25-kHz channel separation environment, intended to operate with a range of 200 nautical miles Equipment Architecture Classes • D.
UL-801 Installation Manual (15) (16) (17) (18) (19) (20) (21) (22) E.
UL-801 Installation Manual (4) (5) (6) (7) (8) (9) (10) VDL Mode A - Ref: ARINC 618, DO-186B VDL Mode A refers to the analog communication protocols exercised by the VHF data radio (VDR) and supported by the UniLink to exchange ACARS messages with any appropriately equipped ground system. This mode is equivalent to the plain old ACARS (POA) function of historical CMUs.
UL-801 Installation Manual CSPs and between the UniLink and peripheral devices, datalink-based crew actions, and other datalink events. Non-TSO Functions (1) (2) (3) 2. Telephony Communication Interface - Ref: SRD The telephony communication interface provides an alternate media for the limited transfer of operator’s AOC messages and weather graphics between the aircraft and the ground.
UL-801 Installation Manual SCN 30.X Application Software Application software version SCN 30.X is categorized as DO-178B Level C (Major). Level C software is defined by DO-178B as “software whose anomalous behavior, as shown by the system safety assessment process, would cause or contribute to a failure of system function resulting in a major failure condition for the aircraft”. SCN 10.X VHF Data Radio Application Software VHF Data Radio Application software version SCN 10.
UL-801 Installation Manual A.
UL-801 Installation Manual 4. Environmental Qualification Forms The environmental categories under which the UniLink is approved (Reference RTCA DO– 160F) are listed on the following Environmental Qualification Forms. ENVIRONMENTAL QUALIFICATION FORM NOMENCLATURE UniLink UL-801 PART NO.
UL-801 Installation Manual Conditions DO-160F Section # Category Description of Conducted Tests Salt Fog 14 X Not tested—Equipment not subjected to salt atmosphere. Magnetic Effect 15 Z Actual class will be measured. (The distance required to cause a compass needle deflection of one degree is measured and must be less than 0.3 meter to be considered compliant with Category Z.) Power Input 16 Z DC generator systems with or without a battery.
UL-801 Installation Manual ENVIRONMENTAL QUALIFICATION FORM NOMENCLATURE Configuration Module PART NO.
UL-801 Installation Manual Conditions DO-160F Section # Category Description of Conducted Tests Magnetic Effect 15 Z Actual class will be measured. (The distance required to cause a compass needle deflection of one degree is measured and must be less than 0.3 meter to be considered compliant with Category Z.) Power Input 16 Z DC generator systems with or without a battery. Not designated to transmit under emergency electrical system conditions.
UL-801 Installation Manual 5. Sample Airplane Flight Manual Supplement Prepare an Airplane Flight Manual Supplement using the following sample as a guide. NOTE: Comments in angle brackets, < >, and italics are explanatory only and should not appear in the final supplement. AFM Supplement for Supplement No.
UL-801 Installation Manual REVISION HISTORY Sheet Rev Description Approved 1-…..
UL-801 Installation Manual TABLE OF CONTENTS Section 1 2 3 4 5 Title General Limitations Emergency and Abnormal Procedures Normal Procedures Performance Data 23-20-06 Page 4 5 8 9 12 Page 114 15 December 2011
UL-801 Installation Manual Section 1 - General A. Installation Description The Universal Avionics Systems Corporation UniLink installation is interfaced with up to three UASC Flight Management Systems. The UniLink contains software 30.X. Section 2 - Limitations A. Operator’s Manual The UniLink Operator’s Manual, report number 23-20-06.
UL-801 Installation Manual Section 4 - Normal Procedures Normal operating procedures are outlined in the UniLink Operator’s Manual, report number 23-20-06.01. . Section 5 – Performance Data No change to FAA Approved Airplane Flight Manual.
UL-801 Installation Manual Equipment Specifications 1. UniLink Equipment Specifications A.
UL-801 Installation Manual B. UniLink Installation Kit (1) Installation Kit P/N K12030-1 Quantity Part Number Description 1 13636-93601-2 or 93601-2 Rack, ARINC 600, 1 MCU (Barry Controls) 6 MS24693C4 Screw, Recessed, Cres, 100° CSK, 4-40 x 3/8” 1 1219 Rack Connector 2 MS51957-20 Screw, 4-40 x 7/8”, Cres (for configuration module) 2 MS21083C04 Nut, 4-40, Cres, Self Lock (for configuration module) NOTE: Equivalent substitutes may be used for the listed items in the installation kits.
UL-801 Installation Manual F. Electronic Part Marking UniLink supports Electronic Part Marking and is in compliance with FAA Order Number 8110.49 which allows verification of the installed part number and software versions by accessing pages on the connected display device such as a CDU or MCDU. The UniLink nameplate, as shown below, makes reference to the Installation Manual (IM) where such information can be found. Per FAA Order number 8110.
2 7.6±.1 23-20-06 (4.2) 2 PO S ITIO N AR IN C 600 C O N N E C TO R P O LA R IZATIO N KEYS TO C O D E #08 . 1. W EIG H T 10801: 4.54 LBS ± 5% CG (8.3) 15.2±.1 CG CG (1) (.5) G. 1.1±.
7.00 6.020 23-20-06 0.545 1.965 CONNECTOR (REF) 1.23 6 PLACES x 100° CSK 0.230 ±0.005 DIA, APPROX REAR OF UNIT 12.220 12.720 9.000 1.77 ±0.02 2 PLACES (MS14108-4) RETAINER, FRONT 0.390 ±0.005 DIA, x 100° CSK 2.50 (2) 14.
UL-801 Installation Manual (3) Configuration Module (P/N 108009) .875" .282" 1.200" (4) Configuration Module Installation Detail 108009 CONFIGURATION MODULE CONNECTOR UL801 RACK CONNECTOR KEYING ARINC 600 #08 POLARIZATION (BLACK SEGMENT INDICATES RACK POST) 4-40 SCREWS AND NUTS NOTE: The darkened portion of the rack connector above indicates the extended part of the key; the light portion indicates the key hole.
UL-801 Installation Manual H. Signal Specifications (1) Digital Inputs (a) FMS ARINC 429 Broadcast Data Label Description Format UNS HS429-1 TX Rate (ms) ARINC 429 HS TX Rate (ms) Notes 102 Selected Altitude BNR 200 N/A Crew selected via CP. 116 Cross-track Distance BNR 100 100 147 Magnetic Variation BNR 1000 500 150 UTC BNR 1000 1000 N/A 203 Pressure Altitude BNR 100 1000 N/A 204 Baro-Corrected Altitude BNR 100 500 ADC dependent.
UL-801 Installation Manual Label Description Format UNS HS429-1 TX Rate (ms) ARINC 429 HS TX Rate (ms) 100 (NOTE 2) N/A 1000 325 Roll Angle BNR 370 WGS-84/GNSS Height BNR 100 (NOTE 1) 1000 371 Equipment ID DSC 1000 Notes N/A N/A NOTE: 1. When in DEMO mode, the label is not transmitted. 2. Label is output during DEMO mode when IRS ATT OUTPUTS is set active. When IRS ATT OUTPUTS is set inactive, these labels are inhibited during DEMO mode.
UL-801 Installation Manual Label Description Format Source 210 True Airspeed 1 (TAS) BNR ADU 1 210 True Airspeed 2 (TAS) BNR ADU 2 211 Total Air Temp 1 BNR ADU 1 211 Total Air Temp 2 BNR ADU 2 212 Altitude Rate 1 BNR ADU 1 212 Altitude Rate 2 BNR ADU 2 213 Static Air Temp 1 (SAT) BNR ADU 1 213 Static Air Temp 2 (SAT) BNR ADU 2 244 Left Fuel Flow BNR Left Fuel Flow Meter 244 Right Fuel Flow BNR Right Fuel Flow Meter 245 Left Gas Gen Speed (NL) BNR FADEC 1 (A/B)
UL-801 Installation Manual (g) ARINC 743 GNSS Broadcast Data Label Description Transmission Rate (ms) 076 GNSS Altitude BNR 1000 103 GNSS Track Angle BNR 1000 110 GNSS Latitude BNR 1000 111 GNSS Longitude BNR 1000 112 GNSS Ground Speed BNR 1000 150 UTC Time BNR 1000 165 Vertical Velocity BNR 1000 260 Date BCD 1000 273 GNSS Sensor Status DSC 1000 Format Transmission Rate (ms) DSC 1000 (h) 604 CMC ARINC 429 Broadcast data Label 270 (2) Format Description Statu
UL-801 Installation Manual I. HS-429-1 Bus – UniLink NOTE: Although there are HS-429-1 labels available for GLS, TAWS, and Vision-1, only the labels for UniLink are shown in the following table.
UL-801 Installation Manual J.
UL-801 Installation Manual Installation and Wiring 1. Installation Considerations for UniLink Mounting A. UniLink Mounting The UniLink may be installed inside or outside of the pressure vessel. The UniLink must not be mounted next to excessive heat producing equipment or in such a way as to impede normal convection cooling and it must not be mounted with its rear connector up. The UniLink may be mounted in any rotational direction in an upright position.
UL-801 Installation Manual A.
UL-801 Installation Manual (2) Sheet 2 of 2 UL-801 (P/N 10801XX) ----CONTINUED---- VHF ANTENNA BP VHF ANTENNA 5 +28 VDC POWER 2 20 POWER GND 4 20 CHASSIS GND 3 16 5A CONFIGURATION MODULE (P/N 108009) TP CONFIG MODULE +28 VDC DATA CLK 11C 24 YELLOW +5 VDC 11D 24 RED DATA I/O 12C 24 BLUE GND 12D 24 BROWN 2 MP DISCRETE INPUT #3 12B DISCRETE INPUT #4 12C PARKING BRAKE SET = GND or OPEN (OPTIONAL, AS REQUIRED) 5 DOOR n OPEN = GND or OPEN (OPTIONAL, AS REQUIRED) 6 NOTE: A
UL-801 Installation Manual B.
UL-801 Installation Manual (2) Sheet 2 of 2 UL-801 (P/N 10801-XX) ----CONTINUED---- VHF ANTENNA BP VHF ANTENNA 5 +28 VDC POWER 2 20 POWER GND 4 20 20 CHASSIS GND 3 16 5A CONFIGURATION MODULE (P/N 108009) TP CONFIG MODULE +28 VDC DATA CLK 11C 24 YELLOW +5 VDC 11D 24 RED DATA I/O 12C 24 BLUE GND 12D 24 BROWN 2 MP DISCRETE INPUT #3 12B PARKING BRAKE SET = GND or OPEN (OPTIONAL, AS REQUIRED) DISCRETE INPUT #4 12C DOOR n OPEN = GND or OPEN (OPTIONAL, AS REQUIRED) 6 5 NO
UL-801 Installation Manual C.
UL-801 Installation Manual (2) Sheet 2 of 2 UL-801 (P/N 10801-XX) ----CONTINUED---- VHF ANTENNA BP VHF ANTENNA 5 +28 VDC POWER 2 20 POWER GND 4 20 20 CHASSIS GND 3 16 5A CONFIGURATION MODULE (P/N 108009) TP CONFIG MODULE +28 VDC DATA CLK 11C 24 +5 VDC 11D 24 RED DATA I/O 12C 24 BLUE GND 12D 24 BROWN YELLOW 2 MP DISCRETE INPUT #3 12B PARKING BRAKE SET = GND or OPEN (OPTIONAL, AS REQUIRED) DISCRETE INPUT #4 12C DOOR n OPEN = GND or OPEN (OPTIONAL, AS REQUIRED) 6 5 NOT
UL-801 Installation Manual D.
UL-801 Installation Manual (2) Sheet 2 of 2 UL-801 (P/N 10801-XX) ----CONTINUED---- VHF ANTENNA BP VHF ANTENNA 5 +28 VDC POWER 2 20 POWER GND 4 20 CHASSIS GND 3 16 +28 VDC 5A CONFIGURATION MODULE (P/N 108009) TP CONFIG MODULE DATA CLK 11C 24 +5 VDC 11D 24 RED DATA I/O 12C 24 BLUE GND 12D 24 BROWN YELLOW 2 MP DISCRETE INPUT #3 12B PARKING BRAKE SET = GND or OPEN (OPTIONAL, AS REQUIRED) 12C DOOR n OPEN = GND or OPEN (OPTIONAL, AS REQUIRED) 6 5 DISCRETE INPUT #4 NOTE: A
UL-801 Installation Manual E.
UL-801 Installation Manual (2) Sheet 2 of 2 UL-801 (P/N 10801-XX) ----CONTINUED---- VHF ANTENNA BP VHF ANTENNA 5 +28 VDC POWER 2 20 POWER GND 4 20 20 CHASSIS GND 3 16 5A CONFIGURATION MODULE (P/N 108009) TP CONFIG MODULE +28 VDC DATA CLK 11C 24 +5 VDC 11D 24 RED DATA I/O 12C 24 BLUE GND 12D 24 BROWN YELLOW 2 MP DISCRETE INPUT #3 12B PARKING BRAKE SET = GND or OPEN (OPTIONAL, AS REQUIRED) DISCRETE INPUT #4 12C DOOR n OPEN = GND or OPEN (OPTIONAL, AS REQUIRED) 6 5 NOT
UL-801 Installation Manual F.
UL-801 Installation Manual (2) Sheet 2 of 2 - 4/5” FPCDU/MCDU UL-801 (P/N 10801-XX) ----CONTINUED---- P3 TP RS-422 DISPLAY DATA TX #3 RS-422 DISPLAY DATA RX #3 4 #1 4"/5 FPCDU/MCDU (P/N 1117-X-X1X, P/N 1018-X-X1X, P/N 1025-XX-XXX) 5 RS-422 DISPLAY DATA RX A 9A E A B 9B F B A 9C B A B 9D C B D SHIELD GND P3 4 RS-422 DISPLAY DATA TX #2 4"/5 FPCDU/MCDU (P/N 1117-X-X1X, P/N 1018-X-X1X, P/N 1025-XX-XXX) 5 E A F B B A C B D SHIELD GND RS-422 DISPLAY DATA RX RS-422 DISPLAY
UL-801 Installation Manual G.
UL-801 Installation Manual (2) Sheet 2 of 2 - 4/5” FPCDU/MCDU UL-801 (P/N 10801-XX) ----CONTINUED---P3 TP RS-422 DISPLAY DATA TX #3 RS-422 DISPLAY DATA RX #3 4 #1 4"/5 FPCDU/MCDU (P/N 1117-X-X1X, P/N 1018-X-X1X, P/N 1025-XX-XXX) 5 A 9A E A B 9B F B A 9C B A C B D SHIELD GND A B 9D B P3 4 RS-422 DISPLAY DATA RX RS-422 DISPLAY DATA TX #2 4"/5 FPCDU/MCDU (P/N 1117-X-X1X, P/N 1018-X-X1X, P/N 1025-XX-XXX) 5 E A F B B A C B D SHIELD GND NOTE: ALL WIRING IS TO BE 22 AWG UN
UL-801 Installation Manual H.
UL-801 Installation Manual (2) Sheet 2 of 2 - 4/5” FPCDU/MCDU UL-801 (P/N 10801-XX) ----CONTINUED---P3 TP RS-422 DISPLAY DATA TX #3 RS-422 DISPLAY DATA RX #3 4 #1 4"/5 FPCDU/MCDU (P/N 1117-X-X1X, P/N 1018-X-X1X, P/N 1025-XX-XXX) 5 A 9A E A B 9B F B A 9C B A B 9D C B D SHIELD GND 4 P3 RS-422 DISPLAY DATA RX RS-422 DISPLAY DATA TX #2 4"/5 FPCDU/MCDU (P/N 1117-X-X1X, P/N 1018-X-X1X, P/N 1025-XX-XXX) 5 E A F B B A C B D SHIELD GND RS-422 DISPLAY DATA RX RS-422 DISPLAY D
UL-801 Installation Manual I.
UL-801 Installation Manual (2) Sheet 2 of 2 UL-801 (P/N 10801-XX) ----CONTINUED---- RS-422 DISPLAY DATA TX #3 RS-422 DISPLAY DATA RX #3 4 P3 TP #1 4" FPCDU/MCDU (P/N 1117-X-X1X) A 9A E A B 9B F B A 9C B A B 9D C B D SHIELD GND 4 P3 RS-422 DISPLAY DATA RX RS-422 DISPLAY DATA TX #2 4" FPCDU/MCDU (P/N 1117-X-X1X) E A F B B A C B D SHIELD GND RS-422 DISPLAY DATA RX RS-422 DISPLAY DATA TX NOTE: ALL WIRING IS TO BE 22 AWG UNLESS OTHERWISE INDICATED.
UL-801 Installation Manual J.
UL-801 Installation Manual (2) Sheet 2 of 2 UL-801 (P/N 10801-XX) ----CONTINUED---- RS-422 DISPLAY DATA TX #3 RS-422 DISPLAY DATA RX #3 4 P3 TP #1 4" FPCDU/MCDU (P/N 1117-X-X1X) A 9A E A B 9B F B A 9C B A B 9D C B D SHIELD GND RS-422 DISPLAY DATA TX #2 4" FPCDU/MCDU (P/N 1117-X-X1X) 4 P3 RS-422 DISPLAY DATA RX E A F B B A C B D SHIELD GND RS-422 DISPLAY DATA RX RS-422 DISPLAY DATA TX NOTE: ALL WIRING IS TO BE 22 AWG UNLESS OTHERWISE INDICATED.
UL-801 Installation Manual K.
UL-801 Installation Manual L. UL-801 to UNS-1Ew (1) Sheet 1 of 2 NOTE: The FMS must be SCN 1005.5/1100.5 or later to support FANS.
UL-801 Installation Manual (2) Sheet 2 of 2 UL-801 (P/N 10801-XX) ----CONTINUED---- VHF ANTENNA BP VHF ANTENNA 5 +28 VDC POWER 2 20 POWER GND 4 20 20 CHASSIS GND 3 16 5A CONFIGURATION MODULE (P/N 108009) TP CONFIG MODULE +28 VDC DATA CLK 11C 24 +5 VDC 11D 24 RED DATA I/O 12C 24 BLUE GND 12D 24 BROWN YELLOW 12 MP DISCRETE INPUT #3 12B PARKING BRAKE SET = GND or OPEN (OPTIONAL, AS REQUIRED) DISCRETE INPUT #4 12C DOOR n OPEN = GND or OPEN 14 (OPTIONAL, AS REQUIRED) 13
UL-801 Installation Manual M. UL-801 to UNS-1Espw (1) Sheet 1 of 2 NOTE: The FMS must be SCN 1000.5/1100.5 or later to support FANS.
UL-801 Installation Manual (2) Sheet 2 of 2 UL-801 (P/N 10801-XX) ----CONTINUED---- VHF ANTENNA BP VHF ANTENNA 5 +28 VDC POWER 2 20 POWER GND 4 20 CHASSIS GND 3 16 5A CONFIGURATION MODULE (P/N 108009) TP CONFIG MODULE +28 VDC DATA CLK 11C 24 +5 VDC 11D 24 RED DATA I/O 12C 24 BLUE GND 12D 24 BROWN YELLOW 11 MP DISCRETE INPUT #3 12B PARKING BRAKE SET = GND or OPEN (OPTIONAL, AS REQUIRED) DISCRETE INPUT #4 12C DOOR n OPEN = GND or OPEN (OPTIONAL, AS REQUIRED) 13 12 NOT
UL-801 Installation Manual N. UL-801 to UNS-1Lw NOTE: The FMS must be SCN 1000.5/1100.5 or later to support FANS.
UL-801 Installation Manual NOTES continued 3 4 IT IS RECOMMENDED THAT DOOR 1 OPEN DISCRETE BE USED IF ONLY ONE DOOR DISCRETE IS TO BE CONFIGURED. UNS1Lw SUPPORTS BOTH UNILINK TEXT AND WEATHER GRAPHICS USING RS-422 DISPLAY DATA. 5 REFER TO APPLICABLE TECHNICAL MANUAL FOR PORT CONFIGURATIONS AND PIN ASSIGNMENTS. 6 IF FMS #1 IS NOT INTERFACED TO THE UL801, THEN CONNECT FMS #2 TO MP1C AND MP1D IN LIEU OF MP2C AND MP2D SHOWN ABOVE. 7 WHITE ATC LETTERING RECOMMENDED.
UL-801 Installation Manual O. UL-801 with FANS to UNS-1Fw (1) Sheet 1 of 2 NOTE: The FMS must be SCN 1000.5/1100.5 or later to support FANS.
UL-801 Installation Manual (2) Sheet 2 of 2 - 4/5” FPCDU/MCDU UL-801 (P/N 10801-XX) ----CONTINUED---P3 TP RS-422 DISPLAY DATA TX #3 #1 4"/5 FPCDU/MCDU (P/N 1117-X-X1X, P/N 1018-X-X1X, P/N 1025-XX-XXX) A 9A E A B 9B F B A 9C B A B 9D C B D SHIELD GND 13 14 13 14 RS-422 DISPLAY DATA RX 16 RS-422 DISPLAY DATA RX #3 #2 4"/5 FPCDU/MCDU (P/N 1117-X-X1X, P/N 1018-X-X1X, P/N 1025-XX-XXX) P3 NOTES: ALL WIRING IS TO BE 22 AWG UNLESS OTHERWISE INDICATED.
UL-801 Installation Manual P. UL-801 FANS Discretes (WAAS FMS SCN 1000.5/1100.5 or later) UL-801 (P/N 10801-XX) 3 ANNUNCIATOR P/N EATON 582-10 A0 B0 C3 F4 L5 N1 (D) P12,12 ATC DISCRETE OUTPUT 2 1 DISCRETE OUTPUT 5 2 7 4 DISCRETE OUTPUT 2 CPDLC CNECT 6 NOTE: ALL WIRING IS TO BE 22 AWG UNLESS OTHERWISE INDICATED. 1 2 CONFIGURE DISCRETE OUTPUT FOR FANS VISUAL. ANY AVAILABLE DISCRETE OUTPUT PIN MAY BE 3 WHITE ATC LETTERING RECOMMENDED.
UL-801 Installation Manual Q.
UL-801 Installation Manual R. UL-801 to MFD-640 – High Resolution (MFD SCN 1011.4.8 or later) UL-801 (P/N 10801-XX) TP RS-422 DISPLAY DATA TX #4 RS-422 DISPLAY DATA RX #4 MFD-640 P/N 6402-XXXXX-XX P1 A 7A 58 A B 7B 57 B 1 1 A 7C 47 A B 7D 46 B RS-422 RX #1 RS-422 TX #1 RETURN/SHIELD NOTE: UNILINK HIGH RESOLUTION CONFGURATION SETTINGS REQUIRE MFD-640-SCN 1011.4.8 OR LATER. 1 USE ANY AVAILABLE RS-422 PORT. PORTS DEPICTED ARE EXAMPLES.
UL-801 Installation Manual S.
UL-801 Installation Manual T. UL-801 to MFD-640 - Low Resolution (MFD-640 SCN 1011.4.
UL-801 Installation Manual U. UL-801 to CVR/CVFDR CVR-120A, CVR-120R, CVFDR-145, CVFDR-145R UL-801 (P/N 10801-XX) ARINC 429 TX H HS OUTPUT TO CVR/CVFDR B CAUTION: 3 3 1 48 SPEED STRAP GND = HS 2 12 VALID GND = VALID 10 H 18 L DATALINK ARINC 429 RX IT IS THE INSTALLER'S RESPONSIBILITY TO VERIFY PIN NUMBERS ON EQUIPMENT MANUFACTURED BY OTHER THAN UNIVERSAL AVIONICS SYSTEMS CORPORATION. 1 PIN 48 (DATA LINK SPEED STRAP) SETS THE ARINC 429 RX PORT TO HIGH OR LOW SPEED.
UL-801 Installation Manual V. UL-801 to DTU-100 UL-801 (P/N 10801-XX) ETHERNET TX ETHERNET RX TP 1 + DTU-100 (P/N 1406-01-X) P2 ETHERNET RX CH 3 N + - ETHERNET TX CH 3 P ETHERNET SHIELD K + - L 2 ETHERNET SHIELD + - J - 3 W. 1 ETHERNET CABLE PER ARINC 646 (10 BASE-T FOR AVIONICS USE). P/N ECS 392404 OR EQUIVALENT. 2 THREE ETHERNET PORTS ARE AVAILABLE. REFER TO THE PIN ASSIGNMENT CHART IN THIS MANUAL. 3 THERE ARE ADDITIONAL ETHERNET PORTS AVAILABLE.
UL-801 Installation Manual X. UL-801 to Portable DTU-100 UL-801 P/N 10801-XX ETHERNET TX 2 + + 3 BULKHEAD CONNECTOR 1 P2 PORTABLE DTU-100 (P/N 1407-01-1) J J J H K K K L ETHERNET RX CH3 L L L H - N N N L ETHERNET SHIELD P P P ETHERNET SHIELD ETHERNET RX CAUTION: ETHERNET TX CH3 IT IS THE INSTALLER'S RESPONSIBILITY TO VERIFY PIN NUMBERS ON EQUIPMENT MANUFACTURED BY OTHER THAN UNIVERSAL AVIONICS SYSTEMS CORPORATION.
UL-801 Installation Manual Z. UL-801 Airborne-based Telephony SatCom Systems (1) UL-801 to Aero-M – without FANS UL-801 (P/N 10801-XX) RS-232 #1 CAUTION: MP TT-3000 AERO-M (P/N 403068A-UAT) TP TX 4A 14 TXD 1 RX 4C 13 RXD 1 GND 3A 16 GND IT IS THE INSTALLER'S RESPONSIBILITY TO VERIFY PIN NUMBERS ON EQUIPMENT MANUFACTURED BY OTHER THAN UNIVERSAL AVIONICS SYSTEMS CORPORATION. NOTES: 1 SIGNAL NAMES ARE IDENTIFIED BY THE MANUFACTURER AND ARE NOT USED TO IMPLY SIGNAL DIRECTION.
UL-801 Installation Manual (3) UL-801 to AirCell and Iridium Systems UL-801 (P/N 10801-XX) RS-232 #1 CAUTION: AIRCELL (AGT.02) IRIDIUM (ST3100) AIRCELL/IRIDIUM (AST3500) MP TX 4A N TX RX 4C a RX GND 3A c GND RS-232 IT IS THE INSTALLER'S RESPONSIBILITY TO VERIFY PIN NUMBERS ON EQUIPMENT MANUFACTURED BY OTHER THAN UNIVERSAL AVIONICS SYSTEMS CORPORATION.
UL-801 Installation Manual (6) UL-801 Connections to International Communications Group (ICG) ICS-220A UL-801 P/N10801-00 ICS-220A MP ARINC 429 BUS TP RX A D4 15A A RX B D5 15B B SHIELD D6 1 TX A D1 13A A TX B D2 13B B SHIELD D3 TP RS-232 CAUTION: 1 ARINC 429 TX #6 MP TX D5 4A TX RX D6 4C RX D8 3A GND GND ARINC 429 TX #3 RS-232 #1 1 IT IS THE INSTALLER'S RESPONSIBILITY TO VERIFY PIN NUMBERS ON EQUIPMENT MANUFACTURED BY OTHER THAN UNIVERSAL AVIONICS SYSTEMS CORP
UL-801 Installation Manual BB. UL-801 to PC Printer UL-801 (P/N 10801-XX) TP GENERIC SERIAL PRINTER DB25 TX 8A 3 RECEIVE DATA RX 8C 2 TRANSMIT DATA GND 3A 7 SIGNAL GROUND RS-232 #2 MP 4 5 CAUTION: RTS CTS IT IS THE INSTALLER'S RESPONSIBILITY TO VERIFY PIN NUMBERS ON EQUIPMENT MANUFACTURED BY OTHER THAN UNIVERSAL AVIONICS SYSTEMS CORPORATION. CC.
UL-801 Installation Manual 3. UL-801 Connector Pin Identification A. Top Plug NOTE: Pin Connector pin differences between the UL-701 and UL-801 top plug are shown in the shaded areas below. These differences are being presented for use when upgrading from UL-701 to UL-801.
UL-801 Installation Manual Top Plug - continued Pin UL-801 Function UL-701 Function 9C RS-422 (A)/RS-232 RX #3 Same 9D RS-422 (B) RX #3 Same 10A RS-232 TX Same 10B RS-232 RX Same 10C RS-232 GND Same 10D Discrete Out #1 Same 11A ARINC 429 (A) TX #4 Same 11B ARINC 429 (B) TX #4 Same 11C Config Mod Clock Same 11D Config Mod Power Same 12A ARINC 429 (A) RX #8 Same 12B ARINC 429 (B) RX #8 Same 12C Config Mod Data (I/O) Same 12D Config Mod GND Same 13A ARINC 429 (A)
UL-801 Installation Manual B. Middle Plug NOTE: Pin Connector pin differences between the UL-701 and UL-801 middle plug are shown in the shaded areas below. These differences are being presented for use when upgrading from UL-701 to UL-801.
UL-801 Installation Manual Middle Plug - continued Pin C.
UL-801 Installation Manual 4. UL-801 Connectors A B C D D C B A 1 1 5 5 5 10 10 10 15 15 A B C D 15 1 5 1 Top Plug 10 A B C D 15 D C B A D C B A 1 1 5 5 5 10 10 10 15 15 A B C D 15 1 5 1 Middle Plug 10 15 D C B A ARINC Key Code #08 Bottom Plug 1 3 1 2 2 4 4 5 UL-801 Connector 3 5 Rack Connector NOTE: The darkened portion of the keying above indicates the extended part of the key; the light portion indicates the key hole.
UL-801 Installation Manual System Data Installation 1. International Civil Aviation Organization (ICAO) Aircraft Type Designators When installing system data during the configuration process, the ICAO aircraft type designator is used. The following tables contain examples of commonly used ICAO designators for various aircraft. Use ICAO Document 8643, found under “Publications” at http://www.icao.int/, to ascertain the correct designator for your aircraft.
UL-801 Installation Manual Manufacturer/Model CANADAIR CL-600/601/604 Challenger RJ Regional Jet CESSNA F406 Caravan 2 441 Conquest, Conquest 2 500, 501 Citation, Citation 1/1SP 525 Citation Jet 526 Citation Jet 550, S550, 551, 552 Citation 2/S2/2SP/Bravo 560 Citation 5 650 Citation 3/6/7 DASSAULT Falcon 10, Mystere 10 Falcon 20, Mystere 20 Falcon 50, Mystere 20 Falcon 900, Mystere 900 Falcon 2000 DEHAVILLAND CANADA DHC-6 Twin Otter DHC-7 Dash 7 DHC-8 Dash 8 DOUGLAS DC-8 DC-9 EMBRAER EMB-110/111 Bandeirante
UL-801 Installation Manual Manufacturer/Model HAWKER HS-124-400/600 HS-125-700 IAI 1123 Westwind 1124 Westwind 1125 Astra Galaxy ILYUSHIN IL96 LEARJET 31 35 45 55 60 LOCKHEED C-130 L-1011 Tristar McDONNELL DOUGLAS DC-8 DC-9 DC-10 MD-81/82/83/87/88 MD-90 MITSUBISHI MU-300 Diamond PIPER PA-42 Cheyenne 3/400 RAYTHEON 90 King Air 200 Super King Air (C-12) 300 Super King Air B300 Super King Air 350 400 Beechjet 1900 Hawker 801 Hawker 1000 REIMS F406 Caravan 2 SIKORSKY S-70 S-76 ICAO Designator H25A H25B WW23 WW
UL-801 Installation Manual Manufacturer/Model TUPOLEV Tu-154 WESTLAND Puma ICAO Designator T154 PUMA 23-20-06 Page 404 15 December 2011
UL-801 Installation Manual 2. Configuration Worksheets Universal Avionics Systems Corporation recommends that the following worksheets be completed in order to assist with configuring the UniLink Configuration Module. One set of worksheets should be filled out and a copy given to the customer. Fill in the blanks and check the appropriate boxes based on the wiring of the aircraft and its set of avionics components. Further, these worksheets may be submitted along with other approval paperwork.
UL-801 Installation Manual A. Customer/Aircraft Information Customer Name: _________________________________________________ Customer Address: _________________________________________________ _________________________________________________ _________________________________________________ B. Aircraft Manufacturer: _________________________________________________ Aircraft Model No.: _________________________________________________ Aircraft Serial No.
UL-801 Installation Manual Press NEXT. DISC IN 2/4 displays.
UL-801 Installation Manual b) DISCRETE (DISC) OUT • FANS VISUAL − Output – Active Open or Active Ground configurable. − Use any available discrete output pin and configure accordingly. − The FANS VISUAL output discrete activates the ATC annunciator and alerts the crew that an ATC advisory is active and the UniLink pages should be accessed to view further information. • FANS AURAL − Output – Active Open or Active Ground configurable. Duration is configurable.
UL-801 Installation Manual DISC OUT 1/5 (Continued) DISC OUT 3 Middle Plug 8B NOT USED VHF NOCOMM CHIME 1 CPDLC CNECT ACTIVE STATE VOX ANNUN SAT NOCOMM CHIME 2 NEW MSG 1 TEL NOCOMM FANS VISUAL GROUND OPEN NEW MSG 2 VDR VOX SEL FANS AURAL Press NEXT. DISC OUT 2/5 displays.
UL-801 Installation Manual Press NEXT. DISC OUT 4/5 displays.
UL-801 Installation Manual c) ARINC RECEIVE • Only one device/interface may configured on each ARINC receive port at a time. • UniLink configures the receive port speed based on the device selected. − The receive port speed for the following devices are configured for low speed: MCDU, Printer, A741 SDU, A604 CMC, IOP. − The receive port speed for the following devices are configured based on the device definition contained within the CDB: A702 FMS, Generic 429 Device.
UL-801 Installation Manual ARINC RX 1/3 (CONTINUED) PORT 5 (A) Top Plug 14C (B) Top Plug 14D PORT 6 (A) Top Plug 13A (B) Top Plug 13B NOT USED 740 PRINT DHC8 IOP1 702 FMS1 750 VDR GENERIC1 NOT USED 740 PRINT DHC8 IOP1 702 FMS1 750 VDR GENERIC1 FMS/CDU1 741 SDU DHC8 IOP2 702 FMS2 TEST GENERIC2 FMS/CDU1 741 SDU DHC8 IOP2 702 FMS2 TEST GENERIC2 FMS/CDU2 VM CMC MCDU2 702 FMS3 ADC1 GENERIC3 FMS/CDU2 VM CMC MCDU2 702 FMS3 ADC1 GENERIC3 FMS/CDU3 604 CMC MCDU3 743A GNSS ADC2 GENERIC4 FMS/CDU3 604 CMC MCDU3 743
UL-801 Installation Manual ARINC RX 2/3 (Continued) PORT 11 (A) Middle Plug 3D (B) Middle Plug 5D PORT 12 (A) Middle Plug 3B (B) Middle Plug 3C NOT USED 740 PRINT DHC8 IOP1 702 FMS1 750 VDR GENERIC1 NOT USED 740 PRINT DHC8 IOP1 702 FMS1 750 VDR GENERIC1 FMS/CDU1 741 SDU DHC8 IOP2 702 FMS2 TEST GENERIC2 FMS/CDU1 741 SDU DHC8 IOP2 702 FMS2 TEST GENERIC2 FMS/CDU2 VM CMC MCDU2 702 FMS3 ADC1 GENERIC3 FMS/CDU2 VM CMC MCDU2 702 FMS3 ADC1 GENERIC3 FMS/CDU3 604 CMC MCDU3 743A GNSS ADC2 GENERIC4 FMS/CDU3 604 CMC
UL-801 Installation Manual d) ARINC TRANSMIT NOTE: • If any ARINC TX port is selected as 741 SDU, then SAT must be selected as the Normal or Alternate option in the PRIORITY (SYS CONFIG 1/4) option page. • If an ARINC TX choice is displayed in small print and there is no arrow pointing to an LSK that selection is not available for use. • VOX tune bus can only be configured for one port. ARINC TX 1/3 PORT 1 (A) Middle Plug 1A (B) Middle Plug 1B NOTE: Only TX port with a default.
UL-801 Installation Manual ARINC TX 2/3 (Continued) FMS/CDU1 741 SDU MCDU1 702 FMS1 TEST LOW PORT 6 (A) Middle Plug 9A (B) Middle Plug 9B PORT 6 SPEED FMS/CDU2 VOX TUNE MCDU2 702 FMS2 FMS/CDU3 VM CMC MCDU3 702 FMS3 740 PRINT 604 CMC CVR 750 VDR FMS/CDU2 VOX TUNE MCDU2 702 FMS2 FMS/CDU3 VM CMC MCDU3 702 FMS3 740 PRINT 604 CMC CVR 750 VDR HIGH FMS/CDU2 VOX TUNE MCDU2 702 FMS2 FMS/CDU3 VM CMC MCDU3 702 FMS3 740 PRINT 604 CMC CVR 750 VDR HIGH Press NEXT. ARINC TX 3/3 displays.
UL-801 Installation Manual Press NEXT. SERIAL 2/2 displays.
UL-801 Installation Manual f) GRAPHICS • Low Resolution Display Devices These devices include all CDUs, MCDUs, RCDUs, MFD-640 (with MFD SCN 1011.4.7 or earlier). A maximum total of four display devices may be used within any of the three CDU graphics ports.
UL-801 Installation Manual Graphics Setup CDU/MFD BAUD RATE 9600 BPS 19.2 KBPS CDU1 GRAPHICS DISP ON There are no defaults. CDU option(s) do not need to be selected if weather graphics are not used.
UL-801 Installation Manual 2. VHF CONFIG VHF CONFIG 1/2 RADIO TYPE NONE CONTACT TIMER ENABLED INTERNAL VDR Internal VDR must be selected if VHF is configured to other than NONE. ARINC 750 VDR DISABLED The contact timer verifies that the current VHF frequency is still usable when the channel has not had any uplink traffic received for a period of time. Enabling this option provides better media management performance.
UL-801 Installation Manual 3. SAT CONFIG SAT CONFIG ENABLED TRACKER TIMER DISABLED The tracker timer provides flight following information to the service provider once every four hours during SatCom medium inactivity. This setting should be enabled to provide better ACARS link management performance. This timer is applicable when UniLink is configured with an A741 SDU. If Iridium is configured as an AIRPHONE, the tracker timer is not active.
UL-801 Installation Manual 5. TEL CONFIG TEL CONFIG 1/2 AIR PHONE Used for dial up modem calls only and uses an RS-232 serial port configured for IRIDIUM or AERO-M. It is primarily used for obtaining color weather maps but may also provide VHF backup. NONE T-T AERO-M When interfacing with Aero-M, configure the Aero-M Data Port (via the Full Feature Handset only, P/N 405621A) for 9600 baud, Flow Control XON/XOFF, “+++”- Mode Enable, Results Code Enabled and ARQ Mode Enabled.
UL-801 Installation Manual TEL CONFIG 1/2 SUSP MSG (Suspend Message) Enables or disables the invocation of the TEL SUSPEND message following a TEL SUSPEND event. ENABLED DISABLED Press NEXT. TEL CONFIG 2/2 displays. REDIAL PAUSE _____ Seconds (5-60 seconds; 30SEC) Redial Pause specifies the wait between telephony redial attempts from 5 to 60 seconds. DIAL ATTEMPTS _____ Attempts (1-6 attempts; 6) Dial Attempts specifies the total number of dial attempts in a set from 1 to 6.
UL-801 Installation Manual 6. POS REPORT These settings control the transmission of present position information while the aircraft is on the ground or in the air. These transmissions are sent to the DSP and may be used to provide flight following for aircraft tracking purposes. Transmission reporting time intervals (INTV) may also be configured. The POS REPORT message is periodic and defaults to every 15 minutes.
UL-801 Installation Manual C. SYS CONFIG 2/4 SYS CONFIG 2/4 MEDIA ADVIS (Media Advisory) ENABLED DISABLED MET DATA (Meteorological Data) ENABLED DISABLED By enabling Met Data for Corporate and American Eagle versions, meteorological data messages are reported to the ground once a Met data message uplink is received from the ground. By enabling Met Data for the Air Nova version, meteorological data messages are reported upon enabling. An uplink is not required. FLIGHT NO.
UL-801 Installation Manual SYS CONFIG 2/4 (Continued) ALERTS NEW MSG DISC DURATION (New Message Discrete Duration) ALERT1 __________________ ALERT2 __________________ CHIME1 __________________ CHIME2 INHIB ON GND (Inhibit on Ground) INHIB ALT (Inhibit Altitude) ALT TYPE (Altitude Type) __________________ __________________ __________________ RADIO RADIO type may only be configured when IOP bus input is used. When RADIO is configured, INHIB ALT must be 2500 feet or below.
UL-801 Installation Manual D. SYS CONFIG 3/4 FANS requirements consist of the following: • The FMS must use SCN 1000.5/1100.5 or later. • UniLink must be connected to the UNS bus from the FMS (not A429 HS bus). • If FANS is enabled, the FMS must be configured with FANS enabled. • If FANS is disabled, the FMS must be configured with FANS disabled. SYS CONFIG 3/4 FANS If FANS is enabled, the FMS must be configured for it and must be at SCN 1000.5/1100.5 or later.
UL-801 Installation Manual SYS CONFIG 3/4 (Continued) GROUND DELAY ______________ MIN (Max 2 N characters) (Minutes); 0MIN A Delay Advisory displays if a delay time other than zero is entered and the Delay Advisory time has elapsed since the occurrence of the OOOI Out event. FANS LATENCY ATC may instruct the crew to utilize a specific value. It’s recommended that the value be configured for 0 (zero). 0 = latency is turned off.
UL-801 Installation Manual 3. Configuration Procedures The Flight Management System (FMS) must be configured to use the UniLink Communications Unit before you configure the UniLink system. Refer to the WAAS/SBAS FMS Configuration Manual, report number 34-61-01, for FMS configuration procedures. NOTE: • • The UASC FMS ARINC receiver port that receives data from the UniLink must be configured for UniLink. Only one receiver port on each FMS may be configured for a datalink device.
UL-801 Installation Manual 3. INIT 1/1 menu. POS INIT 1/1 Â date 23-AUG-11 utc 14:49:45 initial pos id -----N 40 51.01 W 074 03.65 nav database expires 26-AUG-11 ¬ACCEPT fmc ver 1000.5 a. LSK [1L] field is highlighted. Enter the local airport identifier. b. Press ENTER. 4. Local Airport Identifier window. POS KTUS 1/ 1 tucson intl NAV N 32 06.97 ARPT W 110 56.46 elev 2643 mag var E 12.0 ¬ACCEPT a. Press the ACCEPT LSK [5L]. b. The INIT 1/1 menu displays. c. Press the ACCEPT LSK [5L]. d.
UL-801 Installation Manual 6. UNILINK menu. FANS-Enabled • FANS-Disabled If FANS is enabled, the top menu line • displays UNILINK MENU. After the UniLink is configured, a different set of configuration options may be displayed than in the FANS-Disabled menu. • If FANS is disabled, the top menu line displays UNILINK MENU 1/2. Press the NEXT key to access UNILINK MENU 2/2. Additional options may appear at LSK [1L], LSK [3L], LSK [2R], and LSK [3R] depending which choices were made during configuration.
UL-801 Installation Manual Use the completed worksheets, found in the Configuration Worksheets section, and enter that information into UniLink. Work through all the UniLink menus and make any necessary modifications for the configuration. The steps should be performed in the order indicated by the large number in the corner of the text box. Some of the items configured are limited to a small number of options that are selectable by pressing a line select key (LSK).
UL-801 Installation Manual C. Storing UniLink Options When all new or modified UniLink options have been entered, the installer can review the configuration by pressing the REVIEW LSK [4R] on the UniLink SYS CONFIG 1/4 page. This provides easy access to review and confirm any configuration warning from the UniLink. If all modifications are acceptable, press the STORE LSK [1R]. Wait a few seconds and press the STORE LSK again.
UL-801 Installation Manual D. Configuration Edit Mode The Configuration Worksheets, found in the Configuration Worksheet section, should have been completed. These worksheets contain the options needed to configure UniLink. Have these worksheets available when implementing the following procedures. (1) Selecting the UniLink Display Page 1 On the FMS, press [DATA] to display the DATA 1/4 page. DATA 1/4 ¬NAV DATA 2 Press ¬PILOT DATA UNILINK [3R] to display the UNILINK MENU page.
UL-801 Installation Manual (2) Edit/Store Mode 1 Push LSK [1R] to highlight SYS CONFIG 1/4 ¬I/O CONFIG -----® ¬VHF CONFIG TEL CONFIG® ¬SAT CONFIG POS REPORT® ¬PRIORITY the data entry field. Type in the password 456789 and push ENTER. The password will be replaced with the word EDIT and EDIT mode is enabled. ¬UNILINK MENU REVIEW® --:--z RETURN® SYS CONFIG 1/4 ¬I/O CONFIG ¬VHF CONFIG EDIT® ¬SAT CONFIG TELEPHONE® ¬PRIORITY POS REPORT® ¬UNILINK MENU REVIEW® --:--z RETURN® 2 Push EDIT [1R].
UL-801 Installation Manual E. Aircraft Configuration 1 Press the NEXT key on the FMS to display the SYS CONFIG 2/4 page. SYS CONFIG 2/4 media advis enabled STORE® met data disabled AIRCRAFT® flight no. disabled CLEARANCES® oooi data disabled ALERTS® --:--z ¬UNILINK MENU 2 Press LSK [1L] thru [4L] and select the ENABLED or DISABLED option for each item. 4 the Press [1L] to highlight TYPE data entry field. Enter the Type and press ENTER.
UL-801 Installation Manual F. Clearances SYS CONFIG 2/4 media advis enabled STORE® met data disabled AIRCRAFT® flight no disabled CLEARANCES® oooi data disabled ALERTS® --:--z ¬UNILINK MENU 1 Press CLEARANCES [3R] to display the CLEARANCES page. 2 Press LSK [2L] and select the ENABLED or DISABLED option for each item. Repeat for LSK [3L].
UL-801 Installation Manual G. Alerts SYS CONFIG 2/4 media advis enabled STORE® met data disabled AIRCRAFT® flight no disabled CLEARANCES® oooi times disabled ALERTS® --:--z ¬UNILINK MENU 2 1 Push LSK [2L] to highlight the data entry field. Enter a value for ALERT1. Push ENTER to move the cursor to the ALERT2 field. Continuing to push the ENTER key moves the cursor to the CHIME1, CHIME2, INHIB ON GND, INHIB ALT, and AFTER OFF fields.
UL-801 Installation Manual H. System Configuration 3/4 1 Push NEXT on the FMS keypad to display the SYS CONFIG 3/4 page. SYS CONFIG 3/4 fans enabled STORE® fans aural fans latency ºms ºsec delay msg tx supp addr ºmin ------ground delay ºmin --:--z ¬UNILINK MENU 2 Push LSK [1L] to toggle enabled/disabled in the FANS field. Push ENTER to move the cursor to the FANS AURAL field. Push LSK [2L] and enter a value.
UL-801 Installation Manual I. I/O Configuration 1 Press I/O CONFIG [1L] to display the I/O CONFIG page.
UL-801 Installation Manual (1) Discrete In 1 Press DISCRETE IN [1L] to display the DISC IN 1/4 page. I/O CONFIG ¬DISCRETE IN SERIAL® ¬DISCRETE OUT ¬ARINC RECEIVE ¬ARINC TRANSMIT ¬UNILINK MENU 2 Press LSK [2L] to configure DISC IN 1. The DISC IN OPT 1/2 page displays with a list of all available options.
UL-801 Installation Manual (2) Discrete Out 1 Press DISCRETE OUT [2L] to display the DISC OUT 1/5 page. I/O CONFIG ¬DISCRETE IN ¬DISCRETE OUT ¬UNILINK MENU 1/2 page displays with a list of all available options.
UL-801 Installation Manual (3) ARINC Receive 1 Press ARINC RECEIVE [3L] to display the ARINC RX 1/3 page. I/O CONFIG ¬DISCRETE IN SERIAL® ¬DISCRETE OUT GRAPHICS® ¬ARINC RECEIVE ¬ARINC TRANSMIT 2 Press LSK [2L] to configure PORT 1. The ARINC RX OPT page displays with a list of the available options for Port 1. NOTE: Choosing Ports 2 - 16 displays one of ARINC RX OPT 1/4 pages.
UL-801 Installation Manual (4) ARINC Transmit 1 Press ARINC TRANSMIT [4L] to display the ARINC TX 1/3 page. I/O CONFIG ¬DISCRETE IN ¬DISCRETE SERIAL® OUT GRAPHICS® ¬ARINC RECEIVE ¬ARINC TRANSMIT ¬UNILINK MENU ARINC 2 PORT 1 SPEED defaults to LOW. Press PORT 2 SPEED [3L] and select the LOW or HIGH speed option. Repeat for the rest of the ARINC TX ports. Ports 4 - 8 are on ARINC TX pages 2 and 3.
UL-801 Installation Manual (5) Serial Port Configuration I/O CONFIG ¬DISCRETE IN SERIAL® ¬DISCRETE OUT GRAPHICS® ¬ARINC TRANSMIT ¬UNILINK MENU 1 Press SERIAL [1R] to display the SERIAL 1/2 page. ¬ARINC RECEIVE --:--z RETURN® 2 Press PORT 1 [1L] to display the SERIAL OPT 1/2 page.
UL-801 Installation Manual (6) Graphics I/O CONFIG ¬DISCRETE IN ¬DISCRETE OUT SERIAL® GRAPHICS® 1 Press GRAPHICS [2R] to display the GRAPHICS page. ¬ARINC RECEIVE ¬ARINC TRANSMIT ¬UNILINK MENU --:--z RETURN® 2 Press CDU/MFD BAUD RATE [1L] to toggle between 9600BPS and 19.2KBPS. 3 the Press LSK [2L] to display and select graphics configuration for CDU1. GRAPHICS cdu/mfd baud rate ¡ª.
UL-801 Installation Manual J. VHF Configuration SYS 1 Push VHF CONFIG [2L] to display the VHF CONFIG 1/2 page. ¬I/O CONFIG CONFIG STORE® ¬VHF CONFIG TEL CONFIG® ¬SAT CONFIG POS REPORT® ¬PRIORITY ¬UNILINK MENU 2 Push RADIO TYPE [1L] to cycle through the RADIO TYPE options. Push all other configuration options to cycle through and choose the options.
UL-801 Installation Manual K. Satellite (SAT) Configuration SYS 1 Press SAT CONFIG [3L] to display the SAT CONFIG page. CONFIG 1/4 ¬I/O CONFIG STORE® ¬VHF CONFIG TEL CONFIG® ¬SAT CONFIG POS REPORT® ¬PRIORITY ¬UNILINK MENU 2 Press TRACKER TIMER [1L] and select ENABLED or DISABLED. Press AUTO RETURN [2L] and select ENABLED or DISABLED. SAT CONFIG tracker timer ENABLED auto return ENABLED ¬UNILINK MENU REVIEW® --:--z STORE® --:--z RETURN® 3 Press RETURN [5R] to the SYS CONFIG 1/4 page.
UL-801 Installation Manual L. Priority Configuration SYS ¬I/O 1 Press PRIORITY [4L] to display the COMM PRIORITY page. 2 Press 1ST [2L] to cycle through the NORMAL options. Based on which option is chosen, not all options will be seen for each choice. Repeat for 2ND [3L] and 3RD [4L].
UL-801 Installation Manual M. Telephony (TEL) Configuration SYS CONFIG 1/4 ¬I/O CONFIG STORE® ¬VHF CONFIG TEL CONFIG® ¬SAT CONFIG POS REPORT® ¬PRIORITY ¬UNILINK MENU 1 display Press TEL CONFIG [2R] to the TEL CONFIG 1/2 page. REVIEW® --:--z 2 select Press AIR PHONE [1L] to the option for telephony communications. 3 enter Press ACCESS NUMBER [2L] and up to 19 alphanumeric characters for the primary telephone access number. Press ENTER when completed.
UL-801 Installation Manual N. Position Report Configuration SYS ¬I/O CONFIG CONFIG STORE® ¬VHF CONFIG ¬SAT 1/4 TEL CONFIG® CONFIG POS ¬PRIORITY ¬UNILINK MENU REPORT® 1 Press POS REPORT [3R] to display the POS REPORT page. REVIEW® --:--z 2 Press AUTOMATIC REPORTING: IN AIR [2L] and select ENABLED OR DISABLED. 3 Press ON GROUND [3L] and and select ENABLED OR DISABLED.
UL-801 Installation Manual O. Configuration Review SYS ¬I/O CONFIG CONFIG STORE® ¬VHF CONFIG ¬SAT 1/4 TEL CONFIG® CONFIG POS ¬PRIORITY ¬UNILINK MENU REPORT® REVIEW® --:--z 1 Press REVIEW [4R] to display the REVIEW 1/22 page. NOTE: The REVIEW pages are a visual representation of the contents of the UniLink Configuration Module. After reviewing all pages for errors, press NEXT on the keypad to return to the REVIEW Page 1.
UL-801 Installation Manual REVIEW 3/22 discrete out: active state disc out º¡:not used ground ground º:not used º£:not used ground º¢:not used ground ground º:not used --:--z ¬UNILINK MENU RETURN® , , , , , , REVIEW 5/22 ¡¢:not used , º§:not º¶:not º:not ºª:not ¡º:not ¡¡:not ¡:not ¡£:not REVIEW 4/22 used used used used used used used used , , , , , , , , ¬UNILINK MENU REVIEW 6/22 º§:not used º¶:not used º:not used ºª:not used ¡º:not used ¡¡:not used ¡:not used ¡£:not used arinc rx: rx port º
UL-801 Installation Manual sat config: tracker timer:disabled auto return:disabled REVIEW 14/22 normal ¡st:vhf normal nd:none normal £rd:none alternate ¡st:none alternate nd:none alternate £rd:none comm priority: tel config: REVIEW 13/22 voice freq ctrl: disabled ¬UNILINK MENU --:--z RETURN® REVIEW 15/22 air phone:none access number: -------------------wx maps:disabled susp msg:enabled baud rate:¢ººbps redial pause:£ºsec dial attempts:§ --:--z ¬UNILINK MENU RETURN® REVIEW 17/22 sys config ÷¢: m
UL-801 Installation Manual Maintenance, Checkout, and Troubleshooting 1. UniLink Ground Checkout Procedures A. Post Installation Test For instructions on testing the UniLink following the initial installation in an aircraft, the installer should refer to the installation Ground and/or Flight Test Plans that are part of the UniLink installation (TC, STC, Field Approval) certification package.
UL-801 Installation Manual D. Version Check (1) (2) (3) (4) E. Device Status (1) (2) (3) F. From the UNILINK MENU Page 1, press NEXT. Press MAINTENANCE LSK [4L]. Press VERSIONS LSK [3L]. Verify the correct UniLink SCN and Part Number appears on the screen. Ensure all peripheral devices are powered on. Press the DEVICE STATUS LSK [1L] on the MAINTENANCE 1/3 page.
UL-801 Installation Manual G. UL-801 VHF Communications VHF datalink service coverage on the ground may be limited. Coverage may be affected by ground obstacles and may be restricted due to poor line of sight of the VHF ground station antenna. (1) The VHF communications status is indicated on the UniLink COMM STATUS page. Press COMM STATUS LSK [4L] on the UNILINK MENU 1/2 page. (2) If VHF COMM STATUS is COMM/IDLE, a request for ATIS information can be performed on the ground.
UL-801 Installation Manual I. Printer Test (1) (2) (3) (4) (5) (6) (7) J. Verify that printer power is on and has passed its self-test. With the DATA page 1/4 displayed, press UNILINK LSK [3R]. The UNILINK MENU 1/2 will display. Press the NEXT key. Press MAINTENANCE LSK [4L] to display the MAINTENANCE 1/3 page. Press TESTS LSK [2R] to display the TESTS page. Press PRINTER LSK [1L]. The printing message pop-up message will display and a test pattern will be sent to the printer.
UL-801 Installation Manual (9) M. Press LSK [5L] to display the weather map. Verify that the correct map has been received. Checking the UL-801 ARINC 741 SatCom (SAT) NOTE: Ensure that the selected DSP provides this service. (1) (2) (3) Verify that the SatCom SDU is powered up, initialized, and logged on. From the UNILINK MENU 1/2 page, press COMM STATUS. If the SatCom status is NOCOMM/UNAVAILABLE, UniLink has not detected label 270 from the SatCom. This indicates the Sat Link is unavailable.
UL-801 Installation Manual 2. Error Messages A complete list of defined error messages is shown in the following tables: • • • • A. The Pop-up Error Messages table shows the error conditions that result in a pop-up window error message. These errors are deemed significant enough to warrant immediate, detailed annunciation. The General Error Messages table shows the general error messages that may result in a NEW ERROR MSG advisory alert, as well as the recommended actions for resolution.
UL-801 Installation Manual B. General Error Messages UniLink error messages may be found by using either of the following two processes: (1) (2) Press the MSG key to see the messages. a) Press the NEXT key to scroll through the messages. Press the MAINTENANCE LSK [4L] on the UNILINK MENU 1/2 page. a) Press the ERROR LOG LSK [4L] on the MAINTENANCE 1/3 page. NOTE: The Error Log contains all error messages including configuration error messages.
UL-801 Installation Manual General Error Messages Text Action/Description MFD-LR2 INOP Cycle power to UniLink and MFD2. If condition persists contact UASC. If condition is recent or frequent for a particular device, examine connection between the graphics display device and UniLink. MFD-LR3 INOP Cycle power to UniLink and MFD3. If condition persists contact UASC. If condition is recent or frequent for a particular device, examine connection between the graphics display device and UniLink.
UL-801 Installation Manual General Error Messages Text Action/Description SERIAL PRINTER FAILURE Examine the printer and its serial and power connections. PRINT JOB TOO LARGE No action required. UniLink has attempted to forward a corrupted uplink to the printer. Re-request uplink data. [Hardware port] FAIL example: ARINC TX PORT 1 FAIL Cycle power to UniLink. If condition persists contact UASC. THE FATAL ERROR LOG HAS BEEN CORRUPTED No action required.
UL-801 Installation Manual General Error Messages Text Action/Description STATUS TIMEOUT LSK [count, first/last occurrence] No action required. Protocol errors are automatically corrected, usually with no impact to the user. If ENQ TIMEOUT LSK [count, first/last occurrence] condition is frequent, examine connection between the printer and UniLink.
UL-801 Installation Manual General Error Messages Text Action/Description ACARSIP VDR ERROR Cycle power once to the VDR. If condition persists, replace VDR or contact UASC. ASIP CMU ERROR Cycle power once to the VDR. If condition persists, replace VDR or contact UASC. ASIP VDR ERROR Cycle power once to the VDR. If condition persists, replace VDR or contact UASC. VDR SOFTWARE LOAD FAULT Cycle power once to the VDR. If condition persists, contact UASC.
UL-801 Installation Manual C. Configuration Error Messages Configuration Error Messages Text Action MEMORY ALLOCATION ERROR--UNABLE TO Attempt to store configuration. If condition persists LOAD CONFIGURATION MODULE. contact UASC. ERROR READING CONFIGURATION MODULE FROM NON-VOLATILE MEMORY. Attempt to store configuration. If condition persists contact UASC. CONFIGURATION MODULE CRC CODE FAILURE. Attempt to store configuration. If condition persists contact UASC.
UL-801 Installation Manual Configuration Error Messages Text Action AN ADC AND A GNSS RECEIVER MAY NOT BE CONFIGURED TOGETHER Configure UniLink with DADC device(s) or GNSS receiver. DADC and GNSS are dissimilar altitude sources and cannot be configured concurrently, configure UniLink accordingly. AN ADC AND AN ARINC 702 FMS MAY NOT BE CONFIGURED TOGETHER A digital air data computer cannot be configured concurrently with an ARINC 702 FMS, configure UniLink accordingly.
UL-801 Installation Manual Configuration Error Messages Text Action SATCOM IS CONFIGURED BUT NO VALID Configure UniLink either with a valid aircraft AIRCRAFT REGISTRATION IS CONFIGURED. registration in the REGISTRATION field on the A/C CONFIG page or with no ARINC transmit and receive ports for an SDU. SATCOM IS CONFIGURED BUT NO VALID AIRLINE/AGENCY ID IS PRESENT.
UL-801 Installation Manual Configuration Error Messages Text SATCOM IS CONFIGURED BUT IS NOT IN EITHER MEDIA PRIORITY LIST. Action Configure UniLink either with SAT in the desired priority NORMAL and/or ALTERNATE fields on the COMM PRIORITY page or with no ARINC transmit and receive ports for an SDU. TELEPHONY IS CONFIGURED BUT IS NOT IN Configure UniLink either with TEL in the desired EITHER MEDIA PRIORITY LIST.
UL-801 Installation Manual Configuration Error Messages Text Action THE VHF-NOCOMM OUTPUT DISCRETE IS CONFIGURED BUT NO VHF RADIO IS CONFIGURED. Configure UniLink either with the correct radio in the RADIO TYPE field on the VHF CONFIG 2/2 page or with no DISC OUT n field as VHF NOCOMM on the DISC OUT pages. THE SAT-NOCOMM OUTPUT DISCRETE IS CONFIGURED BUT NO SDU IS CONFIGURED.
UL-801 Installation Manual Configuration Error Messages Text Action CDU 2 IS CONFIGURED FOR GRAPHICS BUT Configure UniLink either with ARINC transmit and FMS 2 OR MCDU 2 IS NOT CONFIGURED. receive ports for FMS 2 or MCDU 2, as appropriate, or with NONE in the CDU 2 GRAPHICS DISP ON field on the GRAPHICS setup page. CDU 3 IS CONFIGURED FOR GRAPHICS BUT Configure UniLink either with ARINC transmit and FMS 3 OR MCDU 3 IS NOT CONFIGURED.
UL-801 Installation Manual Configuration Error Messages Text Action HR-1 IS CONFIGURED FOR GRAPHICS BUT Configure UniLink either with an HI-RES DISPLAY 1 NO HI-RES DISPLAY 1 SERIAL INTERFACE IS serial port or remove HR1 from the GRAPHICS setup CONFIGURED. configuration. HR-2 IS CONFIGURED FOR GRAPHICS BUT Configure UniLink either with an HI-RES DISPLAY 2 NO HI-RES DISPLAY 2 SERIAL INTERFACE IS serial port or remove HR2 from the GRAPHICS setup CONFIGURED. configuration.
UL-801 Installation Manual Configuration Error Messages Text Action FANS DISABLED – ATC DATABASE NOT INSTALLED Configure UniLink with FANS functionality ENABLED and load a valid ATC database or configure UniLink with FANS disabled. FANS DISABLED – DUAL UASC FMS NOT CONFIGURED Configure UniLink for two UASC FMSs or configure UniLink with FANS disabled. SQP MIN IS SET BELOW THREE Configure SQP MIN with a value greater than three.
UL-801 Installation Manual Appendix 1 This appendix contains industry-standard acronyms, abbreviations, and terms used in the UniLink Installation manual. 1.
UL-801 Installation Manual Acronym/Abbreviation/Term Description CRC CSDB Cyclic Redundancy Check Commercial Standard Data Bus (Data Interface Format Standard) Clear to Send Cockpit Voice and Flight Data Recorder (UASC) Cockpit Voice Recorder Digital Automatic Terminal Information System (also referred to as ATIS) Departure Clearance Datalink Service Provider (also referred to as DSP) Downlink Message Display Processor Differential Phase Shift Keying Data Transfer Unit (UASC) Data Transfer Unit-100 (UASC
UL-801 Installation Manual Acronym/Abbreviation/Term Description HS ICAO ID IFR IOP I/O LAN LOS LRU LS LSK MARSA MCDU MCDU MCU MDM MFD MIC MSG MSK MVFR ND NDA NOCOMM NO CVG NVM ONBD OOOI High Speed International Civil Aviation Organization Identification, Identifier Instrument Flight Rules Input/Output Processor Input/Output Local Area Network Line of Sight Line-Replaceable Unit Low Speed Line Select Key Military Assumes Responsibility for Separation of Aircraft Multifunctional Control Display Unit (UASC
UL-801 Installation Manual Acronym/Abbreviation/Term Description Packet Mode Data A half duplex bi-directional communication link in which data is accumulated in packets of various lengths and sent out in a burst or bursts so therefore does not support voice communications. Packet switching is the process of routing and transferring data by means of addressed packets so that a channel is occupied during the transmission of the packet only.
UL-801 Installation Manual Acronym/Abbreviation/Term Description TEL VOX VSWR WOW WPT Abbreviation for telephony. The telephony communication link provides a circuit mode data connection via a dial-up modem. A hand shake must be established prior to data being exchanged. Only an RS-232 capable SatCom can be used.
UL-801 Installation Manual Appendix 2 This appendix contains UniLink Menus and subordinate menus. Pages illustrated with dashed boxes are optional and are only available when the functionality reflected on the pages is enabled via UniLink-configured options. 1. UniLink Menus and Submenus – without FANS A. UniLink Menu 1/2 NOTES: 1. 2. 3. 4. Only available if OOOI is enabled in configuration. Only available if VHF is enabled in configuration. Only available if DATA is enabled in configuration.
UL-801 Installation Manual UniLink Menu 1/2 – Continued NOTES: 1. Only available if TEL is enabled in configuration.
UL-801 Installation Manual B. UniLink Menu 2/2 NOTES: 1. Check with DSP for availability of this feature.
UL-801 Installation Manual C.
UL-801 Installation Manual D.
UL-801 Installation Manual 2. UniLink Menus and Submenus – with FANS A.
UL-801 Installation Manual UniLink Menu 1/2 – Continued 23-20-06 Page A2-7 15 December 2011
UL-801 Installation Manual UniLink Menu 1/2 – Continued 23-20-06 Page A2-8 15 December 2011
UL-801 Installation Manual UniLink Menu 1/2 – Continued NOTES: 1. Only available if VHF is enabled in configuration (UL-800 only). 2. Only available if SAT is enabled in configuration. 3. Only available if TEL is enabled in configuration.
UL-801 Installation Manual B.
UL-801 Installation Manual B.
UL-801 Installation Manual C. OPS Menu NOTES: 1. Only available if OOOI is enabled in configuration. 2. Only available if TEL is enabled in configuration.
UL-801 Installation Manual OPS Menu – Continued NOTES: 1. Only available if TEL is enabled in configuration. 2. The SELCAL option only displays when associated messages are available. Check with DSP for availability of this feature.
UL-801 Installation Manual Appendix 3 This appendix contains a list of Datalink Service Providers (DSP) that may be used with the UniLink. 1. Datalink Service Providers Providers Contact Information https://direct.ARINC.net ARINC Direct Honeywell OneLink Aero-I and Aero-M Communication Services 941-360-0680 (24 hr.) 602-822-7502 (Fax) Aviation.Services@Honeywell.com Sat Com Direct 888-448-9003 321-777-3000 321-777-3702 (Fax) SATCOM1 + 45 4615 4546 http://satcom1.com/ Sita http://www.sita.
