U4127
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to “dangerous voltage” and to prevent from a risk of electric shock. Warning: To reduce the risk of electric shock, don’t open the cabinet. Refer servicing to qualified personnel only. The exclamation point within an equilateral triangle is intended to alert the user to important operating and maintenance (servicing). Please read the manual carefully before installing the receiver.
QUICK INSTALLATION GUIDE QUICK INSTALLATION GUIDE FOLLOW NEXT STEPS FOR THE CORRECT INSTALLATION OF THIS RECEIVER. STEP 1: CONNECTIONS The coaxial cable, with satellite signal, must be connected to the “IF IN” connector. The “TV SCART” connector must be connector to the TV set. Depending on the type of installation, the receiver should be connected and configured following next examples. English rev 1.2 Example 1 – Basic System Example 2 – DISEqC switches Example 3 – Combined with terrestrial PAG.
QUICK INSTALLATION GUIDE STEP 2: BASIC CONFIGURATION OF THE RECEIVER Language: press [ ] to select languages. The selection of languages include: English, German, French, Spanish, Italian, Portuguese, Turkish, Polish, Russian, Danish, Greek, Hungarian, Arabic, Farsi. First Audio: Some channels offer more than one audio language. This function allows you to set the preferred audio language for those channels using [ ].
QUICK INSTALLATION GUIDE recommend you to contact your installer or to refer to the user manual of this system to get the correct information. Single search: You can edit the following items (Image 2): IMAGE 3 PAG. 5 English rev 1.2 IMAGE 2 1. Satellite: Press [ ] to switch Satellites or press [OK] to enter satellite list to select directly. 2. LNB Configuration: Selecting this option and pressing [OK], the LNB Configuration menu will be displayed.
QUICK INSTALLATION GUIDE rev 1.2 English IMAGE 4 Multi search: You can edit the following items (Image 4): 1. On “Satellite” item press [OK] to open the satellite list. Then press [ ] to move the highlight and press [OK] to mark/unmark and [EXIT] to finish the selection. You can select several satellites in this menu. At the bottom of the screen you can see the selected satellites. The system will use DiSEqC1.0/1.1, DiSEqC1.2 and USALS functions to search the marked satellites and scan channels. 2.
QUICK INSTALLATION GUIDE STEP 3: TIME CONFIGURATION It is recommended to setup the clock before starting to enjoy the receiver, because correct time maybe is required by some applications. Please complete following options: IMAGE 5 rev 1.2 NOTE: If the current channel provides the correct time information, you will see the current time after you entered “Time” menu. If the channel doesn’t provide time information, you have to input the date and time information manually.
QUICK INSTALLATION GUIDE TV Channel List: This option shows the list of TV stored channels. Radio Channel List: This option shows the list of Radio stored channels. Channel Setup: This option allows setting the receiver to start in a predefined channel. Delete All: This option deletes all TV and Radio stored channels. Restore channel list and settings: This option loads the user TV and Radio channel list, saved previously.
QUICK INSTALLATION GUIDE Language: This option allows choosing the language of the menus. TV System: This option allows choosing the video Standard and other parameters of the screen. Time & Timer Setting: Timer setting menu. Parental Lock: In this option, user can lock the access to the menu and change the password of the receiver. Power setting: Turns on or off the LNB power or enable / disable Low Power Consumption mode. Information: Shows all the technical information for the selected channel.
INDEX Safety Precaution Caution…..…………………...............................………………………………………………12 2. Basic Operations 2.0. Switch on STB……………………….....................................………………………………...14 2.1. Standby ……………………..............................................…………………………………...15 2.2. TTX …………..................................................……………………………………..15 2.3. Mute……………............................................………………………………………..15 2.4. Channel Number…………...........................
INDEX 3.3 Channel Setup…………..................................………………………………......22 3.3.1. Start-up Channel……………................................……………………………......22 3.3.2. Channel Play Type………........................…………………………………......22 3.4. Favourite Channel List Name……..........……………………………………......22 3.5. Delete All……...............……………………………………………….22 3.6. Restore channel list and settings………………..........…………………………………….23 3.7. Save channel list and settings………………..........…………………………………….23 5.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to “dangerous voltage” and to prevent from a risk of electric shock. Warning: To reduce the risk of electric shock, don’t open the cabinet. Refer servicing to qualified personnel only. The exclamation point within an equilateral triangle is intended to alert the user to important operating and maintenance (servicing). Please read the manual carefully before installing the receiver.
PANEL & REMOTE CONTROL DESCRIPTION 1. PANEL & REMOTE CONTROL DESCRIPTION 1.1. FRONT PANEL DESCRIPTION 23 4 5 1. POWER: Switches the receiver on, or enters standby mode. To completely switch off the receiver, you have to use the switch on the back of the receiver. 2. LOCK LED: Indicates a sufficient signal level at the IF IN input. 3. POWER LED: Indicates that the mains voltage (90-230 VAC) is available. 4. IR-SENSOR: Reception sensor for the IR remote control signals. 5.
PANEL & REMOTE CONTROL DESCRIPTION 1 3 4 5 18 6 8 10 13 12 9 20 2 21 16 14 15 17 7 11 2. BASIC OPERATIONS 2.0. SWITCH ON STB Switch the [Device’s Main Power] switch on. When the STB is first used it will display the quick setup page where the receiver can be configured quickly. For further use the STB will play the same channel as last time when it was switched off.
BASIC OPERATIONS 2.1. STANDBY 1. Press [Power] button to switch from TV mode to Standby mode. 2. In Standby mode press [Power] button again to switch back to TV mode. The last active channel will be showed. 3. To switch off the STB complete press the main power button (placed at the rear panel of the receiver). 2.2. TTX OSD 1 2.3. MUTE 1. Press the [Mute] button to mute the sound. On the screen an icon will be displayed to indicate the muted sound (OSD 2). 2.
BASIC OPERATIONS 2.8. VOL+/VOLIn TV mode, press [Vol+/Vol-] to adjust volume. 2.9. EXIT Press [Exit] button to exit the current menu. 2.10. MENU 2.11. RECALL Pressing the [Back] button allows you to toggle between the actual and the last selected channel. OSD 4 2.12. CHANNEL LIST OSD 5 OSD 6 In TV mode press [OK] button to open the Channel List window. Reduced Channel List (OSD 4): You can use [ ] keys to navigate this list. 1. Press [Yellow] button to open the SAT list.
BASIC OPERATIONS 2.13. EPG OSD 8 2.14. LIST In TV mode, press [List] button to access directly to the “TV Channel List” menu or in Radio mode, press [List] button to access directly to to the “Radio Channel List” menu. 2.15. FAVOURITES OSD 9 1. In TV mode press the [Favourite] button to display the Favourite Group window on the screen as the picture beside shows (OSD 10). 2. In the Favourite Group window you can select the desired favourite channel with [ ] and confirm it with [OK] to switch to it.
BASIC OPERATIONS 2.17. INFORMATION In TV mode, press [INFO] button can open information screen (OSD 12), in the window shows the parameters of current channel. 2.18. FAV +/- English OSD 12 1. In TV mode press the [FAV+/FAV-] buttons to switch between the favourites channels in the current Favourite Group directly. 2. The sequence of the favourite channels is following the sequence in the related Favourite Group list. 2.19. ZOOM 1. Press [Zoom] button in TV mode to zoom the image.
CHANNEL 3. CHANNEL OSD 15 3.1. TV CHANNEL LIST OSD 16 OSD 17 If you enter the Channel List menu a window like the one besides will open (OSD 17). 1. You can move the highlighted channel with [ ] and press [OK] to preview the highlighted program in the preview window. 2. You can enter directly the number of the desired channel with the remote control. The selection will select that channel, but it will not be previewed until you confirm with [OK] button. 3.
CHANNEL 3.1.2. MOVE OSD 19 1. To move/change channels: Pushing the [Red] button, you will see a picture like OSD 19. You will be able to move or change the position of the channels: - Push again the [Red] button to move the channel. - Push the [Green] button to change the position of the channel. 2. Move the channel to the desired position with [ ]. Press [OK] to confirm the position. English 3.1.3. SORT OSD 20 1. Press [Green] to open the Sort window (OSD 20).
CHANNEL this menu. OSD 24 3.1.4.3 LOCK In Channel Edit menu, press [Yellow] button to place a Lock icon behind the name of the highlighted channel. Marked channels (OSD 24) will be locked and displayed only after password has been entered if you confirm to save the changes when you leave this menu. 3.1.4.4 EDIT OSD 26 OSD 27 rev 1.2 3.1.5. FIND 1. Press [Blue] button to open the “Find” window like showed besides (OSD 28).
CHANNEL 3.2. RADIO CHANNEL LIST Basically the operation of “Radio Channel List” is same as “TV Channel List” (OSD 29). 3.3. CHANNEL SETUP OSD 29 When you enter the “Channel Setup” menu you will see a screen like beside (OSD 30): English 3.3.1. START-UP CHANNEL OSD 30 Press [OK] to enter “Start-up Channel” menu to see the screen like showed beside (OSD 31): 1. If you set of “Boot on Channel” to “On” you can edit the following two items.
CHANNEL 2. After entering the password correct a safety question will show up where you have to confirm first (OSD 35 next page). 3. Select “Yes” to delete all channels or “No” to cancel and confirm with [OK]. 4. In step 2 and step 3, pressing [Exit] will exit the function directly without saving. OSD 34 3.6. RESTORE CHANNEL LIST AND SETTINGS OSD 35 Using this option, the receiver will load the channels saved as previously as a backup of the user channels list (see point 3.7.).
INSTALLATION 4. INSTALLATION English OSD 38 Press [Menu] in the TV mode to enter the main menu (OSD 38). ] to select the Installation item. 1. Press [ 2. Press [OK] to enter the selected item. In the Installation menu (OSD 39): 3. Press [ ] to select the wanted menu item. 4. Press [OK] to enter the selected item among.
INSTALLATION OSD 42 rev 1.2 OSD 44 4.2. MULTI SEARCH When you enter the “Multi Search” menu a window like the one beside will open (OSD 43). 1. On “Satellite” item press [OK] to open the satellite list (OSD 44). Then press [ ] to move the highlight and press [OK] to mark/unmark and [EXIT] to finish the selection. You can select several satellites in this menu. At the bottom of the screen you can see the selected satellites (OSD 45). The system will use DiSEqC1.0/1.1, DiSEqC1.
INSTALLATION English OSD 46 OSD 47 OSD 48 OSD 49 When you enter “TP Scan” menu a window like the one beside will be displayed (OSD 46): ] to select the satellite 1. On “Satellite” item, press [ you want to scan or press [OK] to open the satellite list for selection. 2. On “TP Index” item use [ ] to select the desired transponder. If any of the TP of the list have tuned and stored channels into the receiver, the following two options “Frequency” and “Symbol Rate” will not be able to be edited.
INSTALLATION will search the selected TP. In case you select “On”, the NIT (Network Identification) will be identified and the receiver will automatically search all the TP of this network. 6. Press [OK] to start scanning. 7. On the “TP Scan” item, press [Exit] to cancel the scanning and saving the found channels. 4.4. SATELLITE LIST OSD 50 OSD 52 rev 1.2 OSD 53 OSD 54 4.5. TP LIST When you open the “TP List” menu you will see a window like the one beside (OSD 53). 1.
INSTALLATION 4.6. SATELLITE GUIDE OSD 56 4.7 UNICABLE CONFIGURATION English OSD 55 When you enter “Satellite Guide” menu, you will see the screen like beside (OSD 57). Here you can enter your local longitude and latitude and the satellite’s longitude. The receiver calculates the antenna’s azimuth and elevation to point your antenna to the selected satellite. 1. Use the [Number] buttons to input the values of “Local Longitude”, “Local Latitude” and “Satellite Longitude”. 2.
SYSTEM SETUP 5. SYSTEM SETUP OSD 60 5.1. LANGUAGE OSD 61 rev 1.2 OSD 62 After selecting the “Language” menu you will see a window like beside (OSD 62): 1. Language: press [ ] to select languages. The selection of languages include: English, German, French, Spanish, Italian, Portuguese, Turkish, Polish, Russian, Danish, Greek, Hungarian, Arabic, Farsi. 2. First Audio: Some channels offer more than one audio language. This function allows you to set the preferred audio ].
SYSTEM SETUP 1. Display Mode is used to switch the display mode. You can select from Auto / PAL / PAL-M / NTSC 3.58. Press [ ] to select the desired mode. 2. Aspect Mode is used to switch the screen aspect ratio mode. You can select from Auto / 4:3 PS / 4:3 LB / 16:9. Press [ ] to select the needed mode. 3. Video Output is use for switching the screen aspect ratio mode. Now we provide below options: RGB / CVBS. You can press [ ] key to select each mode circularly. 4.
SYSTEM SETUP OSD 67 5.3.2. LOCAL TIME SETTING OSD 68 OSD 69 When you select “Local Time Setting” and press [OK] then you will see a window like the one beside (OSD 68): 1. GMT Usage: This item is used to set the time by using the time signal from the satellite. Press [ ] to change the setting. 2. The “GMT Offset” item is only available when “GMT Usage” ] to set the “GMT Offset” value. is set to “On”.
SYSTEM SETUP 5.4. OSD SETTING OSD 72 5.5. PARENTAL LOCK You can set a password for anyone who wishes to operate the “Installation” menu. You can also set the password to lock channels. Below you find how to set and change the password. 1. On “Parental Lock”, press [OK] to open a dialogue box and input the password. After you entered the correct password, you will see a screen like beside (OSD 72): 2.
SYSTEM SETUP NOTE: The default password is 0000 5. Press [Exit] to leave the “Parental Lock” menu. 5.6. POWER SETTING OSD 73 rev 1.2 PAG. 33 English OSD 74 When you select this option, you will see a screen like beside (OSD 73): 1. Automatic standby: In this option you can program the automatic turning off of the receiver (OSD 74). The programming can be made after a period of time between 1 and 8 hours, with 1 h. intervals.
TOOLS 6. TOOLS English OSD 75 Press [Menu] in the TV mode to enter the main menu (OSD 75). ] to select the Tools item. 1. Press [ 2. Press [OK] to enter the selected item. In the Tools menu (OSD 76): 3. Press [ ] to select the wanted menu item. 4. Press [OK] to enter the selected item among. - Information - Quick Setup - Game - Factory Default - Software Upgrade - SatcoDX Auto Programing 6.1. INFORMATION OSD 76 1. When you select the “Information” menu you will see a screen like beside (OSD 77).
TOOLS 6.3. GAME When you enter “Game” menu, you will see three Games include Tetris, Snake and Othello (OSD 79). 6.3.1. TETRIS OSD 79 6.3.2. SNAKE 1. Mark “Setup” and press [ ] to select the level (speed). 2. Mark “Start” and press [OK] to start the game. 3. Mark “Cancel” and press [OK] to leave the game. 4. Play the game: - Press [ ] to guide the snake to the red blocks. Every block you ate increases the length of the snake. If the snake runs against a wall or against itself then it dies.
TOOLS 6.5. SOFTWARE UPGRADE There are two ways of upgrading the software of the receiver as you can see at OSD 81. 6.5.1. SOFTWARE UPGRADE English OSD 81 1. This function allows you to upgrade the software of the receiver. This can be done from PC to receiver or from a master receiver to a slave receiver using a RS232 adaptor through Scart connector. 2. Connect master receiver or PC to the slave receiver via serial interface (0-Modem cable).
TOOLS 6.6. SATCODX AUTO PROGRAMMING OSD 84 rev 1.2 OSD 85 PAG. 37 English This function is using the tables of the SatcoDX websites to update your channel and satellite lists. 1. Start the SatcoDX application on your PC. 2. Select “SatcoDX Auto Programming” item from the “Tools” menu and press [OK]. The screen will show the message “OK to Proceed” (OSD 84). 3. Press [OK] again and you will see the message “Ready to Download” (OSD 85). 4.
TECHNICAL SPECIFICATION VIDEO Decoding Bit rate Output Active pixel Output connector MPEG-2 & MEPG-1 compatible Max 15Mbps PAL/NTSC 720x480 @ 30fps; 720x576 @25fps Scart /RCA AUDIO Decoding Mode Bit rate Output connector MPEG-2/MPEG-1 layer I & II Mono, Dual, Stereo, Joint stereo Max 384Kbps Scart / RCA DEMODULATOR Demodulation Symbol rate Outer code Inner code Energy dispersion QPSK SCPC/MCPC RS (204, 188, 8) ALL DVB rates DVB-S recommendation INPUT SIGNAL Frequency Input level Channel bandwidth Inp
CONFORMITY DECLARATION “WE , UNIVERS BY FTE, DECLARE THAT THE PRODUCTS IS IN CONFORMITY WITH FOLLOWING DIRECTIVES LVD 73/23/EEC EMC 89/336/EEC rev 1.2 AS LAST AMENDED BY 93/68/EEC” PAG.