uTV 2 guide
uTV 2 description The Unitron uTV 2 connects your A2DP Headset wirelessly to your TV or other audio devices. The uTV 2 is connected to your TV (or any other audio source) and wirelessly sends audio signals from your TV to your headset within a range of up to 30 meters (100 ft). hearing aid (f) (g) Legend Buttons (a) ON/OFF button (b) TV signal volume (up) (c) TV signal volume (down) up to 30 meters (100 ft) cable headset uTV 2 Inputs (d) Power input (mini-USB) (e) Audio input (3.
Installation Use the RCA/Cinch cable (i) to connect the uTV 2 to the TV: Step 1: Connecting the uTV 2 To connect the power supply (h): Place the uTV 2 next to your TV. Connect the mini-USB plug (d) of the power suppply to the power input (Power) of the uTV 2. Plug the power supply into the wall socket. Connect the stereo (e) plug to the audio input (Audio IN) of the uTV 2. Connect the red and white plugs (i) to the matching red and white output sockets on your TV.
You can also connect your uTV 2 to the headset socket of your TV, using the audio cable: Connect the stereo plug (e) to the audio input of the uTV 2 (Audio IN). Plug the other end into the headset output socket of your TV. (k) 6 When connecting the uTV 2 to the headset socket of your TV, you are able to adjust the volume via your TV remote control. Some TVs will switch off their loudspeakers when plugging the jack into the headset socket - the TV will not be audible for other people.
Step 2: Switching on 1. Switch on the uTV 2 by a short press of the ON/ OFF button (a) as shown in fig. 2. The status light (g) will illuminate green iniatially and may later switch to blue. uTV 2 (a) (g) ● Initiate the pairing process on your headset as stated in its manual. ● If the uTV 2 status light (g) is not rapidly blinking blue already, press the ON/OFF button (a) for 5 seconds until the Bluetooth indicator (g) is rapidly blinking blue as shown in fig 2.
If the headset moves out of range of the uTV 2, the wireless audio transmission will be terminated. If the headset is then moved back into range of the uTV 2, it will automatically resume streaming to your headset. It may take up to 10 seconds until the streaming resumes. Both streaming light indicators (g) should be solid blue during streaming. If the uTV 2 status light (g): ● is green, make sure TV sound and headset are switched on. ● blinks blue, you are in paused mode.
Step 6: Switching off uTV 2 Compliance information To switch off the devices: Declaration of Conformity ● To end the transmission of the TV audio signal, switch off the uTV 2 by pressing the ON/OFF button (a) as shown in fig. 7. Hereby Unitron declares that this Unitron product is in compliance with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive 1999/5/EC.
Notice 1: This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1.) this device may not cause harmful interference, and 2.) this device must accept any interference received, including interference that may cause undesired operation. Notice 2: Changes or modifications made to this device not expressly approved by Unitron may void the FCC authorization to operate this device.
The CE symbol is confirmation by Unitron that this Unitron product meets the requirements of the 0678 R&TTE Directive 1999/5/EC on Radio and Telecommunication Terminal Equipment. The numbers after the CE symbol are the numbers of consulted certified bodies under the above mentioned directives. The alert sign means that potential restrictions on its use are applicable in one or more EU Member States.
DISTRIBUTOR Unitron Hearing Ltd. 20 Beasley Drive, P.O. Box 9017, Kitchener, ON N2G 4X1 Canada European Representative Max-Eyth-Straße 20, 70736 Fellbach-Oeffingen, Germany www.unitron.