iCube Instruction Guide
Table of Contents Your iCube ......................................................................1 Practical Solutions to Everyday Problems ......................2 Using the iCube Guide ....................................................3 Getting started................................................................4 Using iCube ...................................................................13 Indicators .....................................................................13 Important information...
Your iCube Hearing Healthcare Professional: _______________________ ___________________________________________________ Telephone:__________________________________________ Model: _____________________________________________ Serial Number of iCube: _______________________________ Replacement Batteries: One AAA (1.
Using the iCube Instruction Guide iCube enables the wireless transfer of fitting data from your PC directly to your client’s hearing instruments. Based on Bluetooth technology the fitting process is fast, smooth and stable, and most importantly, cable-free. Please read this manual carefully to benefit from all the features of your iCube. For further information, please visit the Unitron website: www.unitronhearing.com Refer to the table of contents for a complete listing of the topics covered in this guide.
Getting started Installing and using the iCube charger Install the iCube charger by plugging the power supply into a power outlet and docking iCube into the iCube charger as shown below. It is recommended that you use the iCube charger to store and charge iCube whenever it is not in use. This way it will be sufficiently charged and ready for the next fitting session. Charging the battery Your iCube has an internal, rechargeable battery.
indicator starts flashing earlier). A new battery’s full performance is achieved only after two or three complete charge and discharge cycles. Your iCube battery can be charged hundreds of times. If the operating time of your iCube reduces substantially, please contact your local Unitron representative. Operating time Fully charged, your iCube will operate for up to four hours in normal use. Battery consumption and the operating time of the iCube greatly depend on the usage of the device.
CableFree Fitting via Bluetooth connection. However, there are locations where Bluetooth connections are not allowed, so iCube can alternatively be used with a USB connection. In either case, before you can start using your iCube it needs to be connected with your computer. Before you continue, make sure the iCube battery charge is high. Connecting via Bluetooth Connecting your iCube via Bluetooth is done in three steps: 1.
instructions. iCube works within a Bluetooth operating range of up to 10 meters (33 ft.) of the fitting computer. 2. Start the Connection Wizard for iCube With Bluetooth functionality turned ON, you can now initiate the connecting process via the U:fit™ fitting software. If this is the first time using iCube, pressing the iCube button on the detection screen will start the “ConnectionWizard for iCube”. 3.
Bluetooth indicator is blue and flashing fast. iCube is now in pairing mode for two minutes or until pairing is completed. Follow the instructions to complete pairing and finish the connection process for iCube.
Removing a Bluetooth pairing If you wish to remove the Bluetooth pairing from your iCube, press and hold the Bluetooth pairing button for about 10 seconds until the Bluetooth indicator is lit solid blue. Connecting via USB cable If you wish to connect your iCube via USB cable instead of Bluetooth, start the “iCube configuration ” in the U:fit fitting application and choose to use iCube via USB cable. When prompted by the wizard, connect the Mini USB plug of the enclosed USB cable as indicated below.
may be presented with an installation wizard: "Found New Hardware Wizard". If so, let your computer automatically install the necessary driver software. The driver software has already been installed during the U:fit installation and should be identified by the wizard. It is not necessary to insert the U:fit installation CD. After successful installation of the USB driver, continue with the "Connection Wizard for iCube" and follow the instructions. No pairing is required for the USB cable connection.
(Re)connecting the neckloop will activate the built-in antenna and enable iCube to operate correctly. Batteries need to be inserted into the hearing aids and hearing aids need to be turned on prior to detection. Detecting and programming hearing instruments In wireless fitting, where there are no left and right fitting cables, the assignment of left/right is done via U:fit. Click the “Detect” button on the detection screen.
Continue by selecting to either “write to instrument(s)” or to “read from instrument(s) . Now the hearing instruments and iCube are ready for fitting. During the programming of hearing instruments, the right side and the left side fitting indicator flash fast red, and blue, respectively. Using iCube Programming hearing instruments without clients When programming hearing instruments without having your clients wear them, make sure they are in range of iCube.
Indicators Battery indicator Yellow - Slow flash Battery full Yellow - Fast flash Battery empty Yellow - Lit solid Battery charging Fitting Status Indicator Red - Right fitting status indicator flashing fast. iCube is programming the right hearing instrument. Blue - Left fitting status indicator flashing fast. iCube is programming the left hearing instrument.
Software Indicator iCube is built such that it can be upgraded whenever new functionalities are available. Follow the instructions provided together with the new software version. Red/yellow/blue - All three indicators flash fast. iCube is being upgraded. Red/yellow/blue - All three indicators lit solid. This may indicate a software problem. Refer to Troubleshooting section.
Important information Maintenance and care • Clean iCube using a damp cloth. Never use household cleaning products (washing powder, soap, etc.) or alcohol to clean the device. • Protect iCube from excessive moisture and heat. • Protect it from excessive shock and vibration. • When iCube is not in use, turn it OFF and store it in the iCube charger so it will be sufficiently charged and ready for the next fitting session.
• • • • • • technology used in this device is extremely reliable and experiences virtually no interference from other devices. It should be noted, however, that when operating the device near a computer terminal or other strong electromagnetic fields, it may be necessary to be at least 60 centimeters (24“) away to ensure proper operation. If the hearing instrument do not respond to the device because of an unusual field disturbance, move away from the disturbing field.
Troubleshooting Guide CAUSE POSSIBLE REMEDY iCube is no longer recognized by the computer to which it was previously paired • Find the Bluetooth settings on your computer • The Bluetooth and turn Bluetooth functionality ON. functionality of your computer may be disabled. • Move iCube closer to your computer. • iCube is out of range. iCube turns OFF • The battery is empty • Charge iCube iCube is unresponsive and all three indicators are lit solid • Unplug the USB cable and press the reset button.
Declaration of Conformity Unitron Hearing declares under its sole responsibility that the iCube is in conformity with the following standards or other standardizing documents: Radio: EN 300-330 EN 300 328 EMC: EN 60601-1-2 Safety: EN/IEC 60601-1 Implementing the provisions of the MDD 93/42/EEC (Medical Device Directive), R&TTE Directive 1999/5/EC (Radio and Telecommunications Terminal Equipment), EMC Directive 2004/108/EC (Electromagnetic Compatibility) and LVD 2006/95/EC (Low Voltage Directive).
Changes or modifications made to this equipment not expressly approved by Unitron Hearing may void the FCC authorization to operate this equipment. Notice 2 This Class B digital apparatus complies with Canadian ICES-003. Notice 3 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help. Operating conditions This product has been designed for trouble-free operation without restrictions when used as intended, unless otherwise stated in this user guide.
20
U n i t ro n H e a r i n g D i st r i b u to r s C o r p o r at e O f f i c e / I n t e r n at i o n a l 20 Beasley Drive, P.O. Box 9017, Kitchener, ON N2G 4X1 Canada A u st r a l i a Level 2, Norwest Quay, 21 Solent Circuit, Baulkham Hills, NSW, NSW 2153 B e lg i u m Baron de Vironlaan, 60 b-1700 Dilbeek C a n a da 20 Beasley Drive, P.O. Box 9017, Kitchener, ON N2G 4X1 Ch i n a No.
www.unitronhearing.