Quick Start Guide

ManualsBrandsunitech ManualsElectronicsBluetooth UHF Pocket Reader

RP902

Quick Start Guide

V1.2

Package

LCD Display & Operation Mode

Product View

Please make sure the following contents are in

the RP902 gift box.

If something is missing or damaged,

please contact your Unitech representative.

• RP902 One-Slot Charging Cradle

• Hand Strap (P/N 5500-900007G)

• Neck Strap (P/N 3210-900019G)

• Power Supply (P/N 1010-900067G)

Optional Accessories

1. Status LED

2. Communication LED

3. 0.96” LCD

4. Power/Triger Key

5. Select Down/Power Off

6. Function/Select Up Key

7. Antenna Area

8. Battery Lock

9. Battery Cover

10. USB Type-C Port

11. POGO Pin

12. NFC Tag

Bluetooth UHF Pocket Reader

• RFID tags/labels

Left: The icon and the alphabet

indicates the operation mode.

Middle: Time

Right: Battery State

Operation Mode

Icon Operation Mode

USB SPP

BT SPP

BT HID

Buffer

BLE HID

To enable USB SPP and BT SPP mode, Please click

the URL Tag Access APK or scan the barcode to

download.

The Package Contents

• RP902 Terminal

• Battery (P/N 1400-900066G)

• USB Type-C Cable (P/N 1550-905908G)

Note: Once you select a different operation mode, the

terminal will automatically restart.

Summary of content (6 pages)

PAGE 1
Package RP902 Bluetooth UHF Pocket Reader Please make sure the following contents are in the RP902 gift box. If something is missing or damaged, please contact your Unitech representative. The Package Contents • RP902 Terminal • Battery (P/N 1400-900066G) • USB Type-C Cable (P/N 1550-905908G) Optional Accessories • RP902 One-Slot Charging Cradle • Hand Strap (P/N 5500-900007G) • Neck Strap (P/N 3210-900019G) • Power Supply (P/N 1010-900067G) Quick Start Guide • RFID tags/labels V1.
PAGE 2
Specifications Default Settings Frequency 865 - 928 MHz (US/EU/JP/TW/CN) Operating Mode BT SPP Mode Standard EPC global Class1 Gen2, ISO/IEC Read Mode Single Read 18000-6C Power Setting 22 dBm Beep Setting Low 2M: When Power is 27dBm Vibrate Setting Enable (Depends on the type and quantity of Auto Power-off 2 min Read Range 1M: When Power is 22dBm RFID tag and environment) Weight 106g Operating Time > 12 hours with 75,000 tag readings Charge Time 2 hours (via RP902 charging cradl
PAGE 3
Charging the Battery Install the Battery 5. Align two hooks at the bottom of the battery cover with the recesses on the batter compartment and insert, please make sure to completely cover the battery strap. 1. Plug the one end of the USB Type-C cable into the port on the reader and another end into a USB port on the host PC or power adapter. 2. Please fully charge the reader (or until the Status LED turns off) before use. Required Time for full charge: RP902 Charging Cradle: 2 hours. USB Type-C Cable: 3.
PAGE 4
Setting Page Power Up / Shut Down Power Up • Short press the Power / Trigger Key to power up. You will hear short beeps (SPP mode: 1 beep/HID mode: 2 beeps/Buffer mode: 3 beeps) with green flash appears on the communication LED, then the LCD screen will appear. Buffer mode USB SPP mode Operating Mode *BT SPP mode BT HID mode Shut Down • Long press the Select Down / Power Off button for about 3 seconds to shut down the terminal.
PAGE 5
Getting Connected Remove the Battery 1. Short press the power/trigger key to power on RP902. 1. Turn the terminal to its rear side, and push the battery lock to the right to unlock the battery. 2. After powering on RP902, the communication LED should show “flashing blue light”, it means RP902 is waiting for Bluetooth connection. 2. Grab two protrusions on two sides of battery cover, and lift upward to remove it. 3. Pull the battery strap upward to remove. Note: RP902 Supports NFC quick pairing. 3.
PAGE 6
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.