Rugged Handheld Computer - PA760 - User's Manual Version 0.1 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
Revision History Date Change Description Version © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
Preface About This Manual Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice.
1. 2. 3. which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting.
CE RF Exposure Compliance For body-worn operation, this device has been tested and meets the ICNIRP guidelines and the European Standard EN 62209-2, for use with dedicated accessories, SAR is measured with this device at a separation of 0.5 cm to the body, while transmitting at the highest certified output power level in all frequency bands of this device. Use of other accessories which contain metals may not ensure compliance with ICNIRP exposure guidelines.
RoHS Statement This device conforms to RoHS (Restriction Of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the 2012/19/EU concerning electronic waste disposal.
Taiwan NCC Warning Statement 低功率電波輻射性電機管理辦法 第十二條:經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者 均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條:低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有 干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備 之干擾。 注意事項: 1. 使用過度恐傷害視力。 2. 使用30分鐘請休息10分鐘;2歲以下幼兒不看螢幕,2歲以上每天看螢幕不要超過 1小時。 3. 減少電磁波影響,請妥適使用。 v © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
Battery Notice 1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. 2. If a battery performance decreases more than 20%, the battery is at the end of its life cycle.
CAUTION! RISK OF EXPLOSION IF BATTERY IS REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 如果更換不正確之電池行事會有爆炸的風險 請依製造商說明書處理用過之電池 如果更换不正确之电池行事会有爆炸的风险 请依制造商说明书处理用过之电池 Battery charge notice It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0°C to 40°C.
Storage and safety notice Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20°C to 60°C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature. * The message above only applies to the usage of the removable batteries.
Hearing Damage Warning To prevent possible hearing damage, do not listen at high volume levels for long periods. x © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
Worldwide Support unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan – Headquarters Europe Tel: +886-2-89121122 Tel: +31-13-4609292 E-mail: info@hq.ute.com E-mail: info@eu.ute.com Address: 5F, No.
Warranty Policy The following items covered under the unitech Limited Warranty are free from defects during normal use: The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user. xii © 2019 unitech Electronics Co., Ltd.
Table of Contents Preface............................................................................................................. i Regulatory Compliance Statements .............................................................. i Laser Information ........................................................................................ vi LED Information .......................................................................................... vi Battery Notice...........................................
Chapter 3 – Introduction to Applications.........................................49 3.1 USS (unitech scan service) .................................................................. 49 3.2 File Manager ........................................................................................ 52 3.3 Update Center ...................................................................................... 53 3.4 StageGO...............................................................................................
PA760 User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the PA760 gift box. If something is missing or damaged, please contact your unitech representative.
PA760 User’s Manual 1.2 Product Detail PA760 Front View LED indicator Receiver Front camera (by model selection ) Back button Background APP button Microphone Home screen button 2 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual PA760 Rear View Barcode scanner window NFC Hand strap hole Pogo Pin connector for extension modules Rear camera Flash LED Microphone for noise cancellation Battery knobs Hand strap hole Cradle connector 3 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual PA760 Left and Right View Volume up/down Scanner trigger key Power key Function key Scanner trigger key USB Type C connector 4 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 1.3 Specifications System Features CPU 2.2 GHz Octa Core Processor, 64bits Memory 4 GB RAM 32GB/64GB(option) Flash Expanded slot MicroSD, up to 128GB OS Android 9 Languages support English, Simplified Chinese, Traditional Chinese, Japanese, Spanish, German, French and multiple languages Display Gorilla GlassⅢ with 5-point capacitive touch panel 5.
PA760 User’s Manual Engines 1D SE655 Illumination/AIMER : LED 630 ± 30 nm Optical Resolution : 5 mil (minimum readable bar code module size) Scan Repetition Rate : Nominally 50 scans/second Print Contrast : 20% (minimum print contrast) Ambient Light Immunity Light Source : 4845(lux) ± 5% Symbologies : UPC-A/E, EAN-8/13, Codabar, Code 39, Code 39Full ASCI, Code 93, Code 32, Interleaved & Std.
PA760 User’s Manual Regulatory Approvals CE, FCC, NCC, BSMI, VCCI, TELEC, CCC, SRRC, RoHS, DoC, BQB, GMS, N-Mark compliance Communication USB USB OTG Type C Connector for PC/USB drive POGO PIN connector for Cradle WLAN IEEE802.
PA760 User’s Manual Software Android 9 Support camera API and Camera 2 API. Transmitter Frequency Maximum Output Power GSM850 824 – 849MHz 32.5dBm EGSM900 880 – 915MHz 32.5dBm DCS1800 1710-1785MHz 29.5dBm PCS1900 1850 – 1910MHz 29.5dBm FDD 1 1920-1980MHz 23dBm FDD 2 1850 – 1910MHz 23dBm FDD 5 824 – 849MHz 23.5dBm FDD 8 880 – 915MHz 23.5dBm FDD 1 1920-1980MHz 22.5dBm FDD 2 1850 – 1910MHz 22.5dBm FDD 3 1710-1785 MHz 22.5dBm FDD 4 1710 – 1755MHz 22.
PA760 User’s Manual 5150-5350MHz 14dBm 5470-5725MHz 14dBm 5150-5350MHz 14dBm 5470-5725MHz 14dBm 5150-5350MHz 13dBm 5470-5725MHz 13dBm 2400-2483.5MHz 9dBm IEEE 802.11a WLAN 5GHz IEEE 802.11n IEEE 802.11ac Bluetooth® Bluetooth® RFID NFC 13.56MHz N/A Note: The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.
PA760 User’s Manual 1.4 Getting Started 1.4.1 Remove / Install the Battery Cover 1. To unlock the battery by turning up the two knobs. And pull the battery up to remove it. 2. To lock the battery by turning down the two knobs. Make sure the battery is securely closed, or you may be unable to turn on the terminal. WARNING! There is a risk of fire and burns if the battery is handled improperly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water.
PA760 User’s Manual 1.4.2 Charging the Battery If the battery has been discharged for several days, you may need to charge for several minutes before powering it on. Use only the adapter and the USB type C cable that came with this device to charge the battery. When the battery power is too low, make sure to use the power adapter or put into the cradle (strongly recommend) to charge, not the USB type C cable connection with your computer. 11 © 2019 unitech Electronics Co., Ltd. All rights reserved.
PA760 User’s Manual 1.4.3 Turning on the terminal for the first time It is recommended to fully charge PA760 before first use. You can now start up your device to set up the languages, WiFi setting, and date and time. Power-On Button Turn ON your device by pressing the power button on the right side of the terminal. 1.4.
PA760 User’s Manual 1.4.5 Using the Micro SD/ Nano SIM Card The PA760 has 1 x micro SD and 2 x nano SIM card slots inside the battery compartment. Note: Before inserting or removing micro SD card or nano SIM card, please TURN OFF PA760 for the first step. Inserting a Micro SD/ Nano SIM Card 1. To unlock the battery by turning up the two knobs. And pull the battery up to remove it. 2. Insert the tip of the tray ejector tool that came with the package or a small bent paperclip into the eject hole.
PA760 User’s Manual 4. To lock the battery by turning down the two knobs. Make sure the battery is securely closed, or you may be unable to turn on the terminal. Checking PA760 storage Please go to Settings and tap Storage to check the PA760 storage. © 2019 unitech Electronics Co., Ltd. All rights reserved. 14 unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 1.4.6 Battery Status The PA760 provides battery info for users to check the battery status, history view and also set up users preferences. 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap 2. Settings and then tap BatteryInfo. BatteryInfo shows the details of the battery use. 15 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual Chapter 2 – Installation & Operation 2.1 Barcode Setting 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap 2. USS ( unitech scan service ). You are now enter the unitech scan service application. 2.1.1 Settings 1. Please tap on the screen to see all the settings of USS. 16 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.1.1 Barcode Scan 1. Please tap Start Scan to get ready for barcodes scan service. 2. For Save / Load Settings, and Factory Default , Please tap and then tap others. 17 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 3. To save settings, you can also tap Save on the screen and input path then tap OK. The saved data is stored in File Manager. (Please see 3.2 File Manager ) 18 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.2 HF Setting 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap Settings and then tap Connected devices. 2. Tap Connection Preferences to enable NFC 3. Make sure that both devices are unlocked and have NFC turned on. Also make sure that the NFC antenna area of PA760 and the other phone's NFC area are close to one another. Slightly moving the phones until a connection is made. Tap the screen. 19 © 2019 unitech Electronics Co., Ltd.
PA760 User’s Manual 2.3 UHF Setting Current model is not available. 20 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.4 WWAN Setting 1. Turn off the terminal to insert the SIM card. Note : For the instruction, please refer to 1.4.5 Using the Micro SD/ Nano SIM Card. It only applies to the device which supports WWAN. 2. Turn on the terminal, 4G signal will show at the top of the screen. 2.4.1 Mobile Network Settings 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap Settings and then tap Network & internet. 21 © 2019 unitech Electronics Co., Ltd.
PA760 User’s Manual 2. Tap Mobile network for more network settings. 3. To choose different network type, please tap Preferred network type. 22 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.5 WLAN Setting 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap 2. Settings and then tap Network & internet. To see available networks, turn Wi-Fi ON. And tap to choose the available networks. 23 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 3. Choose the available networks, and enter the Password and tap Connect. 4. If the wireless network that you want is not listed, tap + Add network to manually add it. 5. When enabled, the Wi-Fi icon is displayed on the status bar. 24 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.5.1 WLAN Advanced WLAN advanced can enhance the roaming behavior when the device is in areas of particularly low coverage or losing its connection to the network infrastructure and provides the power save mode to control the power consumption setting. WLAN advanced will help users to manage the seamless roaming. 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap Settings and then tap WLAN Advanced. Always tap “Apply” to finish the setting.
PA760 User’s Manual ● Power Save Mode Tap to enable the power save mode to set the wifi module to its optimum power consumption setting. ● Roaming Trigger (Default : -78 dBm Range : -40 dBm ~ - 90 dBm) Roaming trigger will help users to look for a better and stronger signal strength (in dBm) by scanning many access points. When the signal strength is lower than roaming trigger value, roaming trigger will start to look for better access points.
PA760 User’s Manual 2.5.1.1 Other options Tap for more options to import / export the current data from the device. Initialize is able to restore the default settings. 27 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.6 PAN Setting 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap Settings and then tap Connected devices. 2. Tap Connection Preferences to enable Bluetooth 3. Tap ON / OFF to enable / disable Bluetooth® . To pair the available device, turn Bluetooth® ON to choose the available device. 28 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.7 GPS Setting 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap Settings and then tap Security & location. Tap Location. 2. Tap ON/OFF for the permission to use your location information. 29 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.8 PC Setting 1. Connect PA760 to your computer with the USB type C cable. Your computer will recognize it is USB charging. 2. Slide down from top, the system will show as follow picture, then you can select File transfers. 30 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.9 Camera Setting 1. Tap Camera on the main screen. Or scroll the screen from down to top to reach the APPS, and tap Camera. OR 31 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.9.1 Camera Settings For the first time turn on, the screen will show a brief introduction about camera settings. Camera switch 32 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.9.1.1 Scene Mode Setting 2.9.1.2 Camera filter effects 33 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.9.1.3 Settings 34 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.9.2 Record Videos Once tap the record button, it will start recording. 35 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.10 Performing a Hardware Reset You may have to perform a reset if the device freezes (i.e., the terminal no longer responds to the buttons or tapping on the screen). Long press and hold Power button around 10 seconds to restart the device. 36 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.11 Performing Factory data reset 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap Settings and then tap System. 2. Tap Advanced for more options, and then tap Reset options. 37 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 3. You can reset the system on Reset options. When you select Erase all data (factory reset), it will erase all folders. 38 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.12 Programmable Keys The PA760’s keys can be programmed for users to be able to perform different functions or applications. 2.12.1 Programming a key 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap Settings. 2. Tap Programmable keys, and select the keys to remap. 39 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 3. Tap one of KEYCODES or APPS that lists the available functions or applications and select one shortcut to map to the key. 4. The key is successfully mapped to a key code. 40 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.12.2 Enable/ Disable wakeup After the key is mapped to a key code, check the Enable wakeup checkbox to wake PA760 by pressing the programmable keys when PA760 is in sleep mode. Note: This function only applies to KEYCODES. 41 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.12.3 Export / Import a Programmable Key Configuration file ■ Export file 1. Tap 2. Select Export 3. Tap OK Programmable keys exported successfully 42 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual The Programmable Key configuration can be exported to a text file or imported into PA760. Note: The configuration file (keys_config.txt) is saved in File Manager. (For File Manager setting, please refer to 3.2 File Manager ) 43 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual ■ Import file Before importing the file, please make sure the configuration file (keys_config.txt) is in File Manager. 1. Tap 2. Select Import 3. Tap Ok Programmable keys imported successfully The new configuration will be applied immediately after import. 44 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual ■ Reset default 1. Tap 2. Select Reset to default 45 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 2.13 Battery Swap Please follow the steps for the battery swap. 1. Long press power button until you see the pop up window and tap Battery Swap. 2. The LED indicator will start showing red light. Please swap the battery after the LED red light goes off. Please do not turn on PA760 during the battery swap. 3. When the battery swap is done, you can press the power button to wake PA760 again. Note :Please see 1.4.1 Installing the Battery for more information.
PA760 User’s Manual 2.14 Split Screen Split screen function allows you to have two apps work side by side on the same screen. Please follow the steps to enable split screen multitasking. Note: Some apps may not work with split-screen. 1. Tap Background APP button until you see those background apps on the screen. 2. Tap and hold the icon which appears above the APP thumbnail and then select “Split screen.” First APP “Split screen” will be on top of the screen.
PA760 User’s Manual 3. To cancel split screen, simply drag up or down the black bar in the middle of the two APPs to expand the app that you would like to keep in full screen. 48 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual Chapter 3 – Introduction to Applications 3.1 USS (unitech scan service) 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap 2. USS ( unitech scan service ). You are now enter the unitech scan service application. Note : For more Scan Service settings, please refer to 2.1 Barcode Setting. 3.1.1 How to scan 1. Aim the Barcode Scan Engine to the barcode and press one of two scan trigger keys or tap Start Scan button.
PA760 User’s Manual 2. After scanning the barcodes, the barcode information is as shown below. 3. To save the scanned data, tap Save and enter the path and filename, then tap OK. ■ More Options For more options and settings, please tap . 50 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 3.1.2 Multi Decode Scan Multi decode scan function allows users to scan multiple barcodes at once. 1. Tap , Choose Scanner Settings 2. Enable Multi Decode Mode, and input the barcode decode count and start multi decode scan. 51 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 3.2 File Manager 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap File Manager. : Settings : Return to the previous page : Main page : Refresh : Folder arrangement : Folder Information : Flash Storage © 2019 unitech Electronics Co., Ltd. All rights reserved. 52 unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 3.3 Update Center 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap 2. Settings and then tap App Update Center. To update or check the latest version of each application, you will need to do it manually. Refresh 3. Tap for more settings on App Update Center. 53 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 3.4 StageGO StageGO is a configuration staging solution for unitech mobile devices. StageGO helps IT admins to use the 1-click auto configure feature to set up and initialize a device quickly. Devices configure themselves by using configuration scripts and barcodes prepared by the IT admins, the StageGO app, currently available for Android devices, uses unitech devices’ barcode scanning capabilities to load the script barcode into the device and start the self-configuration process.
PA760 User’s Manual barcodes on the printouts (or load the script file). When all barcodes are scanned, StageGO is ready to begin self-configuration. StageGO can also be configured for 1-click auto configuration. On the main screen, scroll the screen from down to top to reach the APPS, and tap StageGO. 55 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
PA760 User’s Manual 3.5 MoboLink MoboLink is a software platform that helps unitech customers to remote manage their purchased devices and applications. The core of the MoboLink platform provides functionalities in the MDM (Mobile Device Management) and MAM (Mobile Application Management) domains, and then further extends into other management functions such as alert notification management and account management. 1. On the main screen, scroll the screen from down to top to reach the APPS, and tap 2.
PA760 User’s Manual 3. Tap , go to Settings. 4. In the Settings section, go to MoboLink Server URL to setup MoboLink server URL. Enter MoboLink Server URL. Save the URL setting 3.5.1 More about MoboLink For detailed operation, solution and usage, please refer to MoboLink user’s guide. ( http://mobolink.tw.ute.com/support ) 57 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.