User Manual Item:Bike Trainer Model No.
Catalogue General information Cautions FCC Statement Disclaimer Product specifications List of components Installation instructions Power training with Zwift Cleaning Maintenance Storage Disposal instructions FAQ 2
General information Please read the User Manual carefully prior to initial use, especially the safety instructions, and only use the indoor bike trainer as described in this User Manual. Non-compliance with the instructions may result in serious injury. The User Manual is an integral component of the indoor bike trainer. Please keep the User Manual in a safe place for future reference. Should you pass the indoor bike trainer on to another user, please be sure to include the User Manual.
Cautions This device is not waterproof, please do not place in the rainy environment for use. Do not place the device in high temperature environment or fire. Do not use this device when you are using Bluetooth heart starter, Bluetooth hearing device and other related physiological devices with the same frequency at the same time. It may cause harm to you. This product contains a button cell battery.
unless they are supervised or if they have been informed about using it safely and understand the relevant risks of use. Children must not play with the indoor bike trainer or any of its parts. Children may not service or clean the product without adult supervision. Do not touch the resistance roller during or after training as this can become very hot. Risk of burns! Keep children and animals away from the indoor bike trainer at all times.
FCC Statement Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device can accept any interference received. If Bluetooth is disconnected by interference, please reconnect.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Disclaimer Slivery & Chavalier is not liable for any temporary or permanent damage to the physical integrity of the user, whether direct or indirect, resulting from the use of the trainer. Product specifications Maximum power 1050w(60Km/h) Net weight 22.9 lbs Flywheel weight 4.
List of components NO Name Quantity A Stand of bike trainer 1 B Resistance unit 1 C Front wheel riser block 1 D Quick-release axle 1 E Open end wrench 2 I The bolt assembly 1 J L-type link assembly 8 Diagram
Installation Instructions ① ② 9
③ ④ 10
⑤ ⑥ ⑦ 11
⑧ Step 1. Assembling your trainer 1.1 Check all parts and quantity according to the List of components. 1.2 As shown in Figure2, unfold the stand A of the bike trainer on the ground. Make sure the supporting foot tubes are extended in place. 1.3 As shown in Figure3, Insert the short end of L-type screw rod into the screw rod cover, And then the other end goes through flat washer, spring, flat washer, the pin, the resistance unit, and finally screw on the adjusting knob. 1.
axle(D) that comes supplied (Users of non-quick release bicycles can skip this step). 2.3 Install the bike on the bike trainer, adjust the screws of both sides to make the bike tire roughly in the middle of the roller. After fixing the bike, Turn the lock nuts to the innermost side, as shown in Figure 7. 2.4 Adjust the adjusting knob clockwise to make the roller tightly touch the tire, and then tighten the adjusting knob for one to two more turns to make the roller fully fit the tire. Step 3.
1. Take the insulating sheet or Battery Replacement Please take out the battery insulation film placed in the battery compartment before use. Use a coin to turn the battery cover in the direction of unlocking, unscrew and re move the battery insulation film, then put back the battery and tighten the battery cover. The same goes for changing the battery 2. Start using 1) Rotate the wheel to activate the sensor. When the LED flashes, the sensor is activated.
3. Wireless Connection Mode This device adopts Bluetooth BLE4.1, ANT+ dual-mode transmission protocols. You can use it to connect with cycling APP, bike computer, sports watch and so on. Set the ring circumference of this device as 170mm/2.126inch on APP or bicycle computer (roller circumference). 1) If your device supports ANT+ mode, you can search for two data: speed and power to connect. The displayed ANT+ ID number (*******) is the same as the bar code number affixed to the outside of the device.
3) Frequent disconnection occurs during use. 6.Training with Zwift app Search for sensors using the Zwift app on your smartphone.
4)Click “LET’SGO” 5) Click“RIDE” Note: Zwift APP need to be downloaded from the official website Cleaning •Do not use pressure washers. •Never use aggressive or solvent-based cleaning agents, metallic sponges or coarse brushes. •No moisture should be allowed to penetrate the resistance roller. If moisture does, however, penetrate the resistance roller, please stop using it. Maintenance Do not make any changes or repairs to any defective parts on the indoor bike trainer.
Check the function of the indoor bike trainer before each use. Check the following points: The indoor bike trainer is positioned on an even surface and is both correctly and securely set up. All screws are tightly fastened. The entire indoor bike trainer is free from damage, stains or cracks. The bike has been securely assembled and cannot come loose from the rear wheel support. Storage Before putting the indoor bike trainer in storage, clean it and let it dry completely.
FAQ About the trainer 1.Is the trainer noiseless? why sometimes it is very noisy? A:The noise is mainly related to the materials and tread of bike tires. The use of road bikes is highly suggested because the spinning sound will be louder and it possible to wear out the tires if mountain bike is used. We also recommend using the bike trainer on a carpet to reduce noise. 2.
5.How many hours can the trainer sensor be used? The battery life is about 400 hours (there will be differences due to the influence to temperature and use environment) If the abnormality still cannot be eliminated, please contact the authorized dealer of UNISKY for assistance. Do not disassemble the product by yourself, resulting in product damage and affecting the after-sales service of the product.
Produced in China for: Slivery & Chavallier ™ Unit G25 Waterfront Studios, 1 Dock Road London E16lAH United Kingdom AFTER SALES SUPPORT service@Sliveryshavalier.