UDR series QUICK GUIDE CAUTION Before operating the unit, please read this manual thorough and retain it for future reference. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Features can be subject to change or modify without any prior notice for its improvement of performance.
FEATURES UDR series radio is very rugged, lightweightand it provides powerful sound, extendedcommunication range and quality sound. UDR seriesradio also provides convenient use andreliable performance in all kinds of industrialfields and public safety sections. The UDR series radio can be programmed by using apersonal computer and program cable whichis connected to a speaker microphone jack on the side ofthe radio. - 1024 channels are selectable.
holding the PTT button on o the left side s of the ra adio. The status indica ation LED lig ghts in red ccolor. And the t radio is convertted to stand dby mode byy releasing the PTT bu utton. It is re ecommende ed to talk ab bout 5~7cm awayfrom the t microph hone for bettter sound quality q and better b voice e communic cation. Monito or Button The recceiving statu us of the se elected chan nnel can be checked byy using the “Monitor” button.
VOX indicator is ON when the VOX mode is activated. ⑤ Scrambler mode indicator is ON when the scrambler function is activated. ⑥ Compander mode indicator is ON when the compander function is activated. ⑦ Radio generates a several kinds of alert tones when the alert tone function is activated. This indicator will be OFF when this function is deactivated. ⑧ Lock indicator is ON when the radio is locked. ⑨ Battery capacity indicator. All the segments are ON when the battery is fully charged.
Removing the Battery Pack *Ensure the ON/OFF volume switch of the radio is set to OFF position. *Press down the locker and slide the battery pack down side of the radio. See Figure. Charging the Battery Pack New batteries or batteries that have been stored, but not used for a long time should be fully chargedbefore placing into service. Low battery voltage would shorten the talk range and affect the performanceof the radio.
Status Charging Complete full charging Error Standby of charging, excess of temperature range LED Red LED is ON Green LED is ON Red LED is blinking Orange LED is ON ☞ CAUTION It is strongly recommended to use the original Chargers provided in each packages. Charging thebattery by using any 3rd parties’ chargers might cause unexpected damage to the battery and radio. CHARGER The standard desktop charger was designed to chargethe high capacity batteries (2600mAh Li-ion)of the UDR series radios.
the transmission will be forced to be controlled for other radios’ users. Receiving You can get into the receiving mode by releasing the PTT button. You can adjust the sound level by usingthe volume switch. In the receiving mode, Green LED will be on and you can check the receiving statuswith the RSSI indication on the LCD. If a receiving frequency is same as that of the current channel, but sub-tone is not same as that of thecurrent setting, then Green LED will blink.
Monitor In order to open the squelch compulsorily, press the MON button. If users press the MON button for morethan 2 seconds, the squelch is opened and stay there continuously with a “beep” sound. If you want to getout of this mode, make a short pressing the MON button again, or turn off and on the radio again. Sub-tone The radio can be programmed for CTCSS encode/decode tone frequencies and DCS code. CTCSS tone frequency A list of standard tone frequencies for CTCSS tone is as shown in below. No.
23 152 49 365 75 664 101 455 24 155 50 371 76 703 102 462 25 156 51 411 77 712 103 523 26 162 52 412 78 723 104 526 Call mode Individual Call _ Enters into the ‘Contacts’ menu by pressing menu button. _ Select an ID that the user wants to communicate with and press the PTT button to communicate. (ID should be pre-programmed by its PC programmer and a transmitting radio’s ID should be listed in a receiving radio) Group Call _ Enters into the ‘Contact’ menu by pressing menu button.
Emergency Call By pressing the red button on top of the radio, the radio will transmit the emergencyalert tone. Also the radio willsound the emergency alert tone via current channel. Users can deactivate the function by pressing the red button again. If this function is set to repeat mode, the emergency alert tone will go off repeatedly. To make the repeat mode off, please press the red button. The function cannotbecome activated during scanning channels.
1) CHANGING GROUP F3 (Pushing for 3sec) _ CHANGING GROUP _ F3 _ “?” & flickering _ F1 or F2 (_,_) then Choose _ F3 (Enter)_ F4 (ESC) 2) SET TX Power F3 (Pushing for 3sec) _ F1 (_) _ SET TX Power _ F3 _ Tx Power Low _ F3 _ “?” & flickering _ F1 or F2 (_,_) then Choose _ F3 (Enter)_ F4 (ESC) 3) SET PASSWORD F3 (Pushing for 3sec) _ F1 (_) _ SET PASSWORD _ F3 _ NEW PASSWORD _ F1 or F2 (_,_) : Choose the Number (ex : “0000”) _ F3 _ AGAIN _ F1 or F2 (_,_) : Choose the Number (ex : “0000”) _ F3 (Enter)_ PASSWORD O
16) Earpiece Mode F3 (Pushing for 3sec) _ F1 (_) _ Earpiece Mode_ F3 _ EAR_MIC ON _ F3 _ “?” & flickering _ F1 or F2 (_,_) then Choose _ F3 (Enter)_ F4 (ESC) 17) SET DISPLAY F3 (Pushing for 3sec) _ F1 (_) _ SET DISPLAY_ F3 _ DISPLAY ENG.
- Performance compromise or troublesoccurring after the warranty period - Troubles of damage due to user’smishandling the device - Troubles caused by natural disasters - Troubles caused by user’s mistake (For example, not following instructionsand safety notes in the manual) - Trouble caused by user’s failure to usethe recommended power source - Troubles caused by repairing orremodeling by the user or unqualifiedperson, not the service personnel ofUNIMO Technology FCC Compliance Notice This device complies
ISEDC RSS warning Informations sur l'exposition aux radiofréquences This equipment complies with ISEDC RF radiation exposure limits set forth for an controlled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For face-up,25mm was used for test, this equipment should be installed and operated with minimum distance 25mm.
