Installation Guide

ManualsBrandsUnbranded ManualsFencingNewport Picket Fence W/Post and No-Dig Steel Pipe Anchor Kit

Check Box for These Contents

In the event of missing or defective parts please call our customer service department at

1 877 234 6196

(Mon. to Fri. 8:00 AM to 4:00 PM EST).

Post Cap

(1)

2. Pickets

(

11) - 7/8” x 3“ x 29¾”

3. Post (1) - 2“ x 3½” x 38 5/8“

Rail Brackets

(4)

5. Top Rail

(1) - 1½” x 3½“ x 68¼”

6. Anchor Pipe

(1) - 46 7/8”

7. Bottom Rail (1) - 1½” x 3½“ x 68¼”

8. 1” Self-Auguring Hex Head Steel Screws (2)

9. 3/4” Self-Auguring Stainless Steel Screws (16)

10.

1/4“ Hardened Steel Drill Bit

(1)

Sold Separately:

 Newport Vinyl Fence Finishing Post (36” High)

with No-Dig Steel Pipe Anchor Kit

Tools You Will Need

• Cordless Drill

• Level

Newport Vinyl Picket Fence with Post

and No-Dig Steel Pipe Anchor Kit

(36” H x 72” W)

Please read through before starting assembly.

ASSEMBLY GUIDE

Not to Scale

IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS

PACKED INSIDE.

Ver 1.1/051615

Ground

70 3/8 in

72 in

2 in

2 15/16 in

68 1/2 in

6 in

18 1/2 in

24 in

4 in

36 in

33 1/2 in

2”x3½” Fence Run Finishing Post with Cap and

No-Dig Steel Pipe Anchor Kit Sold Separately

DO-IT-YOURSELF

FRIENDLY PRODUCTS

Zippity

This fence can easily be trimmed

down horizontally to fit your custom

space. Use a fine toothed circular

saw or hack saw.

Summary of content (9 pages)

PAGE 1
A S S E M B LY G U I D E Newport Vinyl Picket Fence with Post and No-Dig Steel Pipe Anchor Kit (36” H x 72” W) Zippity DO-IT-YOURSELF FRIENDLY PRODUCTS 68 1/2 in 2 15/16 in 6 in 36 in 33 1/2 in 18 1/2 in Ground 2 in This fence can easily be trimmed down horizontally to fit your custom space. Use a fine toothed circular saw or hack saw.
PAGE 2
TOOL OPTIONS FOR DRIVING PIPE INTO GROUND   GOOD BETTER 5lb Sledgehammer  BEST 10lb Sledgehammer  DO NOT USE Hammer Post Pounder Purchase post pounder at any hardware store or go to: www.wambamfence.com. Post pounders cost roughly $25 to $30 at Hardware Store (or rental stores often have for rent). STEP ONE Install Anchor Pipes 1 1 After establishing your fence lines with string and stake, drive your first pipe into the ground.
PAGE 3
STEP T WO Optional: Install Post over Anchor Pipe Optional If your ground is dry and hard, use a claw hammer to loosen 2” or 4“ of dirt around the base of the pipe. This will allow the vinyl post to easily insert itself into the ground in step 2 below. 1 Orient post correctly with tabs at top and slide the vinyl post over the anchor pipe down into the ground. 2 Using a wood block (or something to protect the top of the vinyl extrusion), pound down the post another 2” to 4” below the ground.
PAGE 4
STEP T WO 4 Use the self-drilling tek screw to secure the bottom of just one vinyl post to the pipe as illustrated. The hex head screws are designed to be installed without pre-drilling, however you may find that using the included drill bit for pre-drilling will allow easier installation of hex head screw into pipe. 5 Using a level, adjust the top of the vinyl post to level as illustrated.
PAGE 5
STEP THREE 1 Install Fence Panel 1 Install one vinyl bracket on the vinyl post that has been secured to the pipe using 3/4” screws (approximately 2” off the ground) 2 in 2 Slide second bracket over the opposite end of the bottom rail and slide the rail down into the pre-installed bracket on the opposing side. 3 Use a level on the top of the bottom rail to determine height of opposing bracket and mark for installation. 2 Note: Adjust this post by sliding left or right to fit the rail length.
PAGE 6
STEP THREE 4 4 Temporarily remove bottom rail and install bracket using screws. 5 Install top brackets as illustrated using screws, as per measurement illustrated below. 6 Orientate bottom and top rails correctly (to receive vertical pickets) and slide down into brackets. Use screws to secure. 7 Once the top and bottom rails are secured, fasten the second post, following the same steps as outlined on page 4.
PAGE 7
STEP FOUR Install Pickets & Post Caps 1 Install pickets by inserting through top rail and locking into the bottom rail. Zippity DO-IT-YOURSELF FRIENDLY PRODUCTS 2 Install post caps. Push down on cap to lock it to vinyl post. 1 Install ONE complete panel of fence FIRST 2 Then proceed to install only one or two pipe anchors at a time, until you fully understand the fundamentals. This will help you to avoid repetitive mistakes. . Post tops can be trimmed down as necessary.
PAGE 8
TIPS 1 2. fence panel and posts and continue driving all your pipe. This will enable you to work with an unobstructed string line. 3. 4. For easier spacing of pipe anchors, you can optionally use a piece of 1x4 wood lumber cut at 70 1/4” for step 3 on page two. Use a wood spacing guide (not included) cut to 70 1/4” to help identify the location of your next pipe anchor. 5. Most yards are relatively level and will allow for a fairly simple installation.
PAGE 9
AVO I D T H E S E P I T FA L L S 1. Have you contacted local utilities? You must call before you start installation of your fence to avoid puncturing any unseen underground utilities, especially electrical or gas lines. Fortunately, this is made easy for you. Simply call 811 in the US, or visit www.call811.com In Canada, visit www.transcanada.com/contactus.html 2. Have you checked your local zoning laws?.