Auto-Locking Dual-Purpose Pintle Hitch 7 Ton Capacity C - 2" Ball Size Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
® Thank you very much for choosing an Ultra-Tow XTP Series product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This pintle hitch is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use This 7 ton capacity Ultra-Tow XTP Series Auto-Locking Dual-Purpose Pintle Hitch features a singlepiece, cast ductile iron with an upper steel lock that is designed with an integral shank to fit directly into a 2" receiver hitch without an adapter. The hitch can be used with a ball coupler or tow ring with a 2" to 3" I.D. drawbar eye ring with a 1-1/4'' to 1-5/8'' diameter cross section. Technical Specifications Property Max. Gross Trailer Weight (Pintle) Max.
⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the hitch in confined work areas may put you dangerously close to cutting tools and rotating parts. Keep children and bystanders away from the work area while operating the hitch. Do not allow children to handle the product.
another tool. Never use an accessory that has a lower operating speed or operating pressure than the tool itself. Specific Operation Warnings ⚠WARNING To prevent serious injury or property damage, read and understand the owner’s manual. Do not exceed lowest rated load capacity in hitch system. Maintain adequate vertical down (tongue) load to have control of the trailer (generally 10%), but do not exceed the specified rated capacities. Other steps and inspections are also required.
Before Each Use 1. Inspect the unit for proper operation. 2. Inspect, in particular, the coupling area. Replace it when the wear exceeds 1/8'' (.125'') from the original surface profile. 3. Inspect the unit for worn, damaged, and missing parts. Replace as required. Operating Instructions ⚠WARNING It is the user’s responsibility to be sure the receiver is capable of a 2,800 lbs. vertical load and 14,000 lbs. gross trailer weight.
Un-Hitching 1. Unlock by removing the safety pin. 2. Unhook the safety chain. 3. Flip the locking plate forward until it touches the hitch ball. 4. Jack up the trailer hitch until it clears the hitch ball and resets for the next hook-up.
Connecting to Ball Coupler Hitching Up Make sure all bystanders are in sight before backing the vehicle up to hook up. 1. Before operating, inspect the unit for proper operation, worn, damaged, or missing parts. Secure the mounting. Correct as required before use. 2. Back the vehicle up until the hitch ball is located under the ball hitch, and then lower it into place. 3. To lock, insert safety pin into the ball coupler. 4.
instruction manual for additional information about engine maintenance. The following chart is based on a normal operation schedule. Maintenance Interval Maintenance Point The following should be performed every 10,000 miles or 6 months: 1. Inspect for proper operation. 2. Inspect, in particular, the coupling area. Replace when the wear exceeds 1/8'' from the original surface profile. 3. Inspect for worn, damaged, and missing parts. Replace as required. 4. Always use a safety clip. 5.
Parts Diagram Parts List Reference 1 2 3 4 5 6 7 8 9 10 11 Part Number PCH7T HM93 HM140 HM53 HM54 HM55 HM56 HM106A HM58 HM59 HM91 Item Description Base Combo Hitch Locking Plate ½''-13UNC x 3'' Cap Screw ½''-13UNC Steel Lock Nut 5/16'' Dia. Alum Rivet Safety Chain Push Nut 2” Hitch Ball Assembly ¼'' Dia x 2 ¼'' Lg.
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only ("You'' or “Your'') that the Ultra-Tow XTP Series product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.