Full Product Manual
STEP 1: CHOOSE INSTALL LOCATION
This installation will use the power and
linking cords included with your ProLink
light fixtures. Make sure that the 5ft. power
cord will reach the nearest outlet and that
the 18in. linking cord will be able to reach
the nearest light fixture. The mounting
location should be indoors, dry and able
to support the module.
DO NOT ATTEMPT TO INSTALL WITH
THE POWER ON.
STEP 2: MARK SCREW LOCATIONS
With a pencil, mark the screw locations
using the keyholes on either end of the
module for guidance.
STEP 3: PRE-DRILL HOLES
Pre-drill holes for the screws using the
pencil markings for guidance. Use a 1/16in.
drill bit.
STEP 4: INSERT SCREWS
Insert the screws with a #1 Phillips
screwdriver, leaving 1/8in. beyond
the surface.
STEP 5: MOUNT MODULE
Align the keyholes on the module with the
screws and slide it into place. Tighten the
screws as needed using only the screwdriver.
STEP 6: CONNECT WITH LIGHT FIXTURE
Insert the linking cord (included with
your ProLink light fixtures) into the port
on the module and connect it with the
closest fixture.
DO NOT EXCEED 80 WATTS OF
CONNECTED LED LIGHTING.
STEP 7: PLUG INTO OUTLET
Insert the power cord into the port on the
module. Then, plug the power cord into a
120VAC 60Hz outlet.
MOTION CONTROLS
Wave your hand once within 3in. of the
motion sensor to turn all connected lights
ON. Wave it a second time to turn the
lights OFF.
TROUBLESHOOTING
Detection range seems to vary: The
detection range of the motion sensor can
dier based upon a variety of factors,
including the tone of the the user’s skin,
the amount of light in the room and
proximity of other objects.
Connected Light Stays on or stays o:
This motion sensor should be mounted
18” above a countertop with no objects
directly beneath it. Objects directly under
the sensor can impede its ability to fuction
properly.
Connected Light is dim or operates
erratically: Verify connected ProLink
products do not exceed electrical ratings
of the ProLink motion sensing switch DO
NOT EXCEED 80 WATTS of connected
ProLink products.
IMPORTANT SAFETY INSTRUCTIONS
This product is intended only for use
with lighting fixtures that are specifically
compatible with the ProLink linking
system.
• Do not install the module while plugged
in or with plugged in lighting fixtures.
• Do not alter the connectors in any way.
• Save these instructions for future use.
DO NOT exceed maximum electrical
ratings listed above. To make sure your
installation will not exceed ratings, add
the current (A) or wattage (W) rating for
all light fixtures that will be connected to
the switch. The total sum of the current
or wattage for all connected light fixtures
cannot exceed the maximum listed above
for the type of module being installed.
WARNINGS TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS:
This fixture has a polarized plug (one blade is wider
than the other) to reduce the risk of electric shock.
This plug will fit into a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician. Never use an extension cord unless the
plug can be fully inserted. Do not alter the plug.
• Read the entire installation procedure before
you begin.
• Not to be used with a dimming circuit or any other
electronically switched control.
• Do not attempt to install the fixture while
plugged in.
• Save these instructions so you can refer to them at
a later time.
Thank you for your purchase!
Instructions
made easy
Exclusive deals
Read instructions or
watch easy-to-follow
video. Scan code or visit
byjasco.com/54875i
For deals, to register your
purchase and to tell us how
we’re doing, simply scan
the code or visit
byjasco.com/deals
Having problems?
Let us know how we can help.
Call 1-800-654-8483 between
7AM-8PM, M-F, Central Time.
Like our product?
Leave a review on your
favorite retailer website
or amazon.com
INSTALLATION OPERATION
PRE-DRILL
MARK
MOUNT
Motion-Activated
In-Line Switch
User Manual
See reverse for easy-to-follow
instructions and exclusive deals.
IMPORTANT: BEFORE INSTALLING, READ ALL SAFETY
INSTRUCTIONS LISTED AT THE END OF THIS MANUAL.
MOTION
Discover more premium LED
lighting and lighting accessories
at byjasco.com/lighting