uPLAY TODAY CUMBERLAND GAP MODEL # UPLAY-007-N MODEL # UPLAY-007-P Issued/Revised: 07/17/14 800.458.5872 www.ultraplay.
uPLAY TODAY CUMBERLAND GAP Dear UPlayToday™ Customer, Thank you for choosing to purchase and install a UPlayToday commercial playsystem by UltraPlay®. We appreciate the confidence you have placed in our company, and we will strive to earn your trust. This is your Owner's Manual & Assembly Instructions booklet. We have designed this manual specifically for the products that you have purchased.
uPLAY TODAY GENERAL COMMERCIAL PLAYGROUND SAFETY GUIDELINES Maintaining your playground equipment and its surrounding area is essential to minimizing the risk of injury to users as well as maximizing its useful lifespan. UPlayToday STRONGLY recommends that you follow these Safety Guidelines in conjunction with conducting periodic maintenance inspections using the accompanying Playground Maintenance Checklist. When installing your playground, always consider local conditions.
uPLAY TODAY GENERAL COMMERCIAL PLAYGROUND SAFETY GUIDELINES Install Wood Mulch (EWF) at a depth of 12". Over time this mulch will compress to a depth of 9" as required by the U.S. Consumer Product Safery Commission, ASTM standard F-1487 and Canadian Standard CAN/CSA-Z-614. For more information on the proper surfacing materials, call the CPSC hotline at 1-800-638-2772. Worn surfaces around equipment should be restored. Concrete footings should never be exposed.
uPLAY TODAY GENERAL COMMERCIAL PLAYGROUND SAFETY GUIDELINES TRIPPING HAZARDS: There should be no exposed concrete footings, abrupt changes in surface elevations, tree roots, tree stumps, and rocks, which can trip children and adults. Check for trip hazards, such as the balance beam support posts, or environmental trip hazards, such as rocks or roots in the play area. Make all necessary improvements or repairs. AFTER THE EQUIPMENT IS IN USE: -Never add components not intended for use with this product.
uPLAY TODAY GENERAL COMMERCIAL PLAYGROUND SAFETY GUIDELINES -Proper maintenance of UPlayToday equipment requires regular tightening of all bolts, nuts, set screws, and other hardware. -All equipment should be free of rust and repainted with an appropriate lead-free paint whenever necessary to deter rusting. This should also be done for any chipped or peeling areas. -Regular checking of all parts, casting, etc., should be made. If part is broken or worn it should be replaced immediately.
uPLAY TODAY GENERAL COMMERCIAL PLAYGROUND SAFETY GUIDELINES -Check for accessible sharp edges or points. Check for protruding bars, bolts, nuts, etc. Eliminate these conditions. -Check for exposed ends of tubing that should be covered with plugs or caps. -Check for loose bolts, nuts, etc. and tighten. -Check for broken or missing rails, steps, rungs, or seats and replace. Issued/Revised: 07/17/14 800.458.5872 www.ultraplay.
uPLAY TODAY UPlayToday Warranty UltraPlay warrants its products to be free from defects in materials and/or workmanship, subject to normal usage and installation, for a period of 1-year from the date of shipment to the original purchaser. In the event of a claim under this warranty, UltraPlay will replace the component at no cost within the first 12 months from date of shipment to the original customer.
uPLAY TODAY WARRANTY EXCLUSIONS All warranties specifically exclude damage caused by man-made or natural disasters, vandalism, negligence, improper installation or improper use, modification, changes in appearance resulting from weathering, scratches, dents, discoloration, normal wear and tear, or marring as a result of public or private use.
uPLAY TODAY GENERAL INTRODUCTION TO INSTALLATION INSTRUCTIONS IMPORTANT! Please read the entire Installation Instructions packet before beginning the installation. UltraPlay has designed UPlayToday to take advantage of all Consumer Product Safety Commission (CPSC) and ASTM guidelines in force at the time of purchase in an effort to prevent playground accidents.
uPLAY TODAY GENERAL INTRODUCTION TO INSTALLATION INSTRUCTIONS TOOLS REQUIRED: UltraPlay supplies only the special wrenches and bits required to fasten the "tamper-resistant" hardware and components. You will need common wrenches and an Allen key set as well as a drill, string line, level, shovels, post hole digger, pry bar, washable felt tip marker, phillips head screw driver, utility knife, rubber mallet, and a tape measure. A power post hole digger may facilitate installation in some circumstances.
uPLAY TODAY GENERAL INTRODUCTION TO INSTALLATION INSTRUCTIONS 7. CPSC guidelines mandate that there shall be no gaps present in the playground equipment that fall between 3-1/2" and 9". The positioning of certain components by the installer can affect this criteria, so you should always measure distances created when attaching components in order to avoid these spaces which can cause entrapment of a child using the equipment.
uPLAY TODAY WARNING LABEL APPLICATION INSTRUCTIONS The enclosed Warning Labels must be affixed to your playground equipment. At least one Warning Label is needed per play structure, permanently affixed in a conspicuous location within easy view of users. INSTRUCTIONS: 1. Fully assemble and install your UPlayToday playground equipment per the accompying installatioin instructions. 2.
uPLAY TODAY TOOLS REQUIRED Issued/Revised: 07/17/14 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 HARDWARE REFERENCE M8 B.H.C.S. Bolts 100mm 45mm 70mm 50mm 40mm 35mm 20mm 30mm 25mm 13mm 4" 1-3/4" 2-3/4" 1-9/16" 2" 1 3/8" 3/4" 1-3/16" 1" 1/2" (33-11-0101) (33-11-0102) (33-11-0103) (33-11-0104) (33-11-0105) (33-11-0106) (33-11-0109) (33-11-0114) (33-11-0107) (33-11-0113) M8 Barrel Nut (33-11-0501) M8 Flat Washer (33-11-0300) M8 Lock Washer (33-11-0301) M8 Lock Nut (33-11-0500) Clamp Rivet (33-11-0700) M10 B.H.C.S.
uPLAY TODAY UPRIGHT PLACEMENT UPRIGHTS LIST DESCRIPTION QTY 12 11' UPRIGHT PART NUMBER 02-07-5028 11' UPRIGHT (02-07-5028) 11' UPRIGHT (02-07-5028) 11' UPRIGHT (02-07-5028) Issued/Revised: 07/17/14 800.458.5872 www.ultraplay.
uPLAY TODAY USE ZONE TOP VIEW CRAWL TUNNEL (02-07-5017) 4FT RIGHT CURVED SLIDE (02-07-5005) 6'-0" BASS DRUM (02-07-5023) GAME PANEL (02-07-5013) RAINWHEEL (02-07-5022) 4FT ADA STEPS (02-07-5000) WINDOW PANEL (02-07-5010) BONGO DRUMS (02-07-5024) 6'-0" 32'-7" BONE BRIDGE (02-07-5016) BARRIER PANEL (02-07-5011) SQUARE DECK (02-07-5001) 4FT STRAIGHT SLIDE (02-07-5004) ROOF (02-07-5015) BENCH PANEL (02-07-5014) SHIP'S WHEEL PANEL (02-07-5012) VINE CLIMBER (02-07-5008) 35'-4" MINIMUM USE ZONE* R
uPLAY TODAY FOOTING DETAIL - SURFACE MOUNT (33-12-0053) DESCRIPTION CONCRETE ANCHOR Parts List QTY 69 PART NUMBER 33-11-0702 UPRIGHT POST UPRIGHT FOOTER 067 CONCRETE ANCHOR CONCRETE 4" MINIMUM w/3000 PSI GRAVEL IMPORTANT: Never install play equipment over hard, unresilient surfaces such as asphalt, concrete, or compacted earth. It is the owner's responsibility to ensure the "minimum area required" contains an appropriate amount of resilient material to cushion accidental falls.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 FOOTING DETAIL - SURFACE MOUNT 1. Using Upright Footers as template, mark hole position on concrete. Drill 3/8" Dia. x 2" deep holes into concrete to receive anchor. 2. Attach Upright Footers to concrete using Concrete Anchor, Flat Washer, and Lock Nut. See Detail 067. LOCK NUT FLAT WASHER UPRIGHT FOOTER CONCRETE ANCHOR 067 Issued/Revised: 07/17/14 800.458.5872 www.ultraplay.
uPLAY TODAY FOOTING DETAIL - ON GROUND (33-12-0116) DESCRIPTION GROUND SPIKE IMPORTANT: UPRIGHTS WILL COME PRE-ASSEMBLED WITH UPRIGHT FOOTER POSITIONED IN THE BOTTOM (2) HOLES TO ACCOMODATE 2" OF SURFACING. WHEN INSTALLING 12" OF SURFACING, REMOVE BOLTS AND ADJUST UPRIGHT FOOTER POSITION TO UTILIZE THE TOP (2) HOLES.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 FOOTING DETAIL - ON GROUND 1. With Upright Footers in position, secure each Upright Footer to the ground using Ground Spikes. NOTE: A 4lb. hammer may be required to drive spikes into the ground. Install ground spikes angled inward as shown in illustration. See Detail 068. IMPORTANT: Refer to Post Placement/Hole Locations diagram to mark locations of Upright Footers.
uPLAY TODAY FOOTING DETAIL - IN GROUND (33-12-0095) Parts List DESCRIPTION QTY INGROUND FOOTER 23 69 3/8" x 1 1/4" P.B.H.C.S. w/PATCH 3/8" FLAT WASHER 69 69 3/8" HEX NUT PART NUMBER 02-07-0049 33-05-0019 33-02-0002 33-01-0002 UPRIGHT UPRIGHT FOOTER SURFACING 069 IMPORTANT: UPRIGHTS WILL COME PRE-ASSEMBLED WITH UPRIGHT FOOTER POSITIONED IN THE BOTTOM (2) HOLES TO ACCOMODATE 2" OF SURFACING. WHEN INSTALLING 12" OF SURFACING, REMOVE BOLTS AND ADJUST UPRIGHT FOOTER POSITION TO UTILIZE THE TOP (2) HOLES.
0 INCH 0 CM 1 3 2 1 2 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 FOOTING DETAIL - IN GROUND 1. Attach Inground Footer to Upright Post using 3/8" x 1 1/4" P.B.H.C.S., 3/8" Flat Washer, and 3/8" Hex Nut. Refer to Footing Table and Footing Layout page for Hole/Footer location. See Detail 069. 2. Continue assembling unit before pouring concrete. Refer to specific component installation instructions. IMPORTANT: POURING CONCRETE IS THE VERY LAST STEP! 3/8" x 1 1/4" P.B.H.C.S.
uPLAY TODAY CUMBERLAND GAP Parts List DESCRIPTION TUBE CLAMP PANEL CLAMP PANEL CLAMP 90° DOUBLE 4FT ADA STEPS SQUARE DECK 4FT.
uPLAY TODAY CUMBERLAND GAP PANEL CLAMP (02-07-0040) ROOF (02-07-5015) 11' UPRIGHT (02-07-5028) CRAWL TUNNEL (02-07-5017) 4FT STRAIGHT SLIDE (02-07-5004) GAME PANEL (02-07-5013) 4FT RIGHT CURVED SLIDE (02-07-5005) BASS DRUM (02-07-5023) BONGO DRUMS (02-07-5024) WINDOW PANEL (02-07-5010) RAINWHEEL (02-07-5022) PANEL CLAMP 60° DOUBLE (02-07-0041) FINISHED ASSEMBLY MODEL # UPLAY-007-N MODEL # UPLAY-007-P TUBE CLAMP (02-07-0039) SQUARE DECK (02-07-5001) 4FT ADA STEPS (02-07-5000) VINE CLIMBER (02-07-5
253 1/4 in [643.46 cm] TOP VIEW CUMBERLAND GAP (UPLAY-007) Vertical Dim. 23 186 1/4 in [473.06 cm] 22 14 15 9 8 6 7 3 4 16 10 17 11 20 21 18 19 12 13 Horizontal Dim. 5 1 Hole No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 FOOTING TABLE Hor. Dim. Ver. Dim.
uPLAY TODAY TUBE CLAMP 02-07-0039 DESCRIPTION TUBE CLAMP Parts List QTY 1 PART NUMBER 02-07-0039 Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete line are included with Hardware Complete Number Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 TUBE CLAMP 02-07-0039 M8 x 25mm (1") BHCS BOLT (33-11-0103) UPRIGHT M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) 030 CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP IN UPRIGHT TO INSTALL CLAMP RIVET. (33-11-0700) Issued/Revised: 06/03/13 800.458.5872 www.ultraplay.
uPLAY TODAY PANEL CLAMP - SINGLE 02-07-0040 DESCRIPTION PANEL CLAMP Parts List QTY 1 PART NUMBER 02-07-0040 Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete line are included with Hardware Complete Number Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 PANEL CLAMP - SINGLE 02-07-0040 UPRIGHT M8 x 25mm (1") BHCS BOLT (33-11-0103) M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) 025 DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET. (33-11-0700) Issued/Revised: 06/04/13 800.458.5872 www.ultraplay.
uPLAY TODAY PANEL CLAMP 90° - DOUBLE 02-07-0041 Parts List DESCRIPTION QTY 1 PANEL CLAMP 90° DOUBLE PART NUMBER 02-07-0041 Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete line are included with Hardware Complete Number Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 PANEL CLAMP 90° - DOUBLE 02-07-0041 PANEL CLAMP 90° - DOUBLE (02-07-0041) M8 LOCK NUT (33-11-0500) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP IN UPRIGHT TO INSTALL CLAMP RIVET. (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) 065 Issued/Revised: 06/04/13 800.458.5872 www.ultraplay.
uPLAY TODAY ADA STEPS 02-07-5000 Parts List DESCRIPTION ADA BARRIER LEFT ADA BARRIER RIGHT 1" FOOTER ADA TRANSFER STAIR ADA DECK ADA DECK SUPPORT POST ADA HANDHOLD ADA STEP 8 1/4" EXTENSION POST 15" EXTENSION POST FOOTER PLATE HARDWARE COMPLETE M10 x 25mm (1") BHCS BOLT M10 x 35mm (1 3/8") BHCS BOLT M10 x 50mm (2") BHCS BOLT M10 x 60mm (2 3/8") BHCS BOLT M10 FLATWASHER M10 LOCK NUT M8 x 25mm (1") BHCS BOLT M8 LOCKWASHER M8 LOCK NUT CLAMP RIVET QTY 1 1 4 1 1 1 1 1 2 2 2 1 13 8 4 2 32 27 12 4 8 4 PART NUMBE
uPLAY TODAY ADA STEPS 02-07-5000 7. Attach ADA Transfer Step to ADA Barriers using M10 x 25mm B.H.C.S. Bolt, M10 Flat Washer, and M10 Lock Nut. See Detail 032. 8. Attach Barrier Footer to ADA Deck Support using M10 x 35mm B.H.C.S. Bolt and M10 Lock Nut. See Detail 028. 9. Attach ADA Deck Support to under side of ADA Deck using M10 x 35 B.H.C.S. Bolt, M10 Flat Washer, and M10 Lock Nut. See Detail 031. 10. Insert Barrier Footer into ADA Handhold and secure using M10 x 35mm B.H.C.S. Bolt and M10 Lock Nut.
uPLAY TODAY ADA STEPS 02-07-5000 029 ADA BARRIER LEFT (02-07-0008) ADA BARRIER RIGHT (02-07-0010) 030 031 ADA HANDHOLD (02-07-0011) ADA DECK (02-07-0004) ADA STEP (02-07-0006) ADA TRANSFER STAIR (02-07-0005) 035 032 031 UNDERNEATH 036 031 033 UNDERNEATH UNDERNEATH COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY 028 FINISHED ASSEMBLY 034 UNDERNEATH ADA DECK SUPPORT POST (02-07-0047) = INSTALLATION DETAIL Issued/Revised: 04/22/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 3 5 4 6 7 5 4 8 9 10 11 12 6 13 14 15 ADA STEPS 02-07-5000 BARRIER M10 LOCK NUT (33-11-0400) M10 x 35mm (1 3/8") BHCS BOLT (33-11-0005) TUBE CLAMP SUPPORT POST M8 x 25mm (1") BHCS BOLT (33-11-0103) M8 LOCKWASHER (33-11-0301) FOOTER 029 028 M8 x 25mm (1") BHCS BOLT (33-11-0103) M10 LOCK NUT (33-11-0400) M10 FLATWASHER (33-11-0200) UPRIGHT M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) D
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 ADA STEPS 02-07-5000 M10 LOCK NUT (33-11-0400) DECK M10 LOCK NUT (33-11-0400) M10 FLATWASHER (33-11-0200) STAIR M10 FLATWASHER (33-11-0200) M10 x 25mm (1") BHCS BOLT (33-11-0003) DECK SUPPORT M10 FLATWASHER (33-11-0200) BARRIER M10 x 35mm (1 3/8") BHCS BOLT (33-11-0005) 032 033 M10 LOCK NUT (33-11-0400) M10 LOCK NUT (33-11-0400) M10 FLATWASHER (33-11-0200) STEP M10 FLATWASHER (33-11-0200) HANDHOLD M10 x 50mm (2"
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 ADA STEPS 02-07-5000 EXTENSION POST M10 LOCK NUT (33-11-0400) M10 x 35mm (1 3/8") BHCS BOLT (33-11-0005) LARGER HOLE FOOTER PLATE 036 Issued/Revised: 04/22/13 800.458.5872 www.ultraplay.
uPLAY TODAY SQUARE DECK 02-07-5001 Parts List DESCRIPTION SQUARE DECK HARDWARE COMPLETE M10 x 30mm (1 3/16") BHCS BOLT M10 FLATWASHER M10 LOCK NUT QTY 1 1 4 4 4 PART NUMBER 02-07-0003 33-12-0019 33-11-0004* 33-11-0200* 33-11-0400* Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete line are included with Hardware Complete Number Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children.
uPLAY TODAY SQUARE DECK 02-07-5001 SQUARE DECK (02-07-0003) 044 UNDERNEATH COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY = INSTALLATION DETAIL FINISHED ASSEMBLY Issued/Revised: 04/30/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 SQUARE DECK 02-07-5001 M10 FLATWASHER (33-11-0200) M10 LOCK NUT (33-11-0400) FLANGE DECK M10 x 30mm (1 3/16") BHCS BOLT (33-11-0004) 044 Issued/Revised: 04/30/13 800.458.5872 www.ultraplay.
uPLAY TODAY 4FT.
uPLAY TODAY 4FT. STRAIGHT SLIDE 02-07-5004 8. Attach Slide Hood to Panel Clamp using M8 x 20mm B.H.C.S. and M8 Barrel Nut. See Detail 061. 9. Close Panel Clamps around Uprights and secure using M8 x 25mm B.H.C.S. and M8 Lock Nut. See Detail 025. (Do not install Clamp Rivet until entire unit is assembled.) 10. Plumb and level entire assembly before tightening all fasteners. NOTE: Apply Loctite to threads of Bolt to prevent from loosening.
0 INCH 0 CM 1 1 2 3 2 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 4FT. STRAIGHT SLIDE 02-07-5004 M8 x 25mm (1") BHCS BOLT (33-11-0103) MOUNTING BRACKET M10 x 35mm (1 3/8") BHCS BOLT (33-11-0005) M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) M10 LOCK NUT (33-11-0400) CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
0 INCH 0 CM 1 1 2 3 2 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 4FT.
uPLAY TODAY 4FT.
uPLAY TODAY 4FT. CURVED SLIDE 02-07-5005 6. Clean out slots in Deck with utility knife if necessary. 7. Attach Slide to Deck using M10 x 20mm B.H.C.S, M12 Lock Washer, and M10 Flat Washer. See Detail 058. 8. Attach Slide Hood to Slide using M10 x 60mm B.H.C.S, M12 Lock Washer, and M10 Flat Washer. See Detail 059. 9. Attach Bottom of Slide Hood to Deck using M8 x 40mm B.H.C.S, M8 Flat Washer, and M8 Lock Nut. See Detail 060. 10. Attach Slide Hood to Panel Clamp using M8 x 20mm B.H.C.S. and M8 Barrel Nut.
0 INCH 0 CM 1 2 3 2 1 4 3 5 6 7 5 4 8 9 10 11 12 6 13 14 15 4FT. CURVED SLIDE 02-07-5005 PLATFORM MOUNTING BRACKET M10 x 35mm (1 3/8") BHCS BOLT (33-11-0005) M8 x 25mm (1") BHCS BOLT (33-11-0103) M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) M10 LOCK NUT (33-11-0400) CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
0 INCH 0 CM 1 3 2 1 2 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 4FT.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 4FT. CURVED SLIDE 02-07-5005 UPRIGHT SLIDE M8 BARREL NUT (33-11-0501) PANEL CENTER SUPPORT POST M8 x 20mm (3/4") BHCS BOLT (33-11-0102) M10 FLATWASHER (33-11-0200) PANEL CLAMP M12 LOCKWASHER (33-11-0203) 061 062 M10 x 20mm (3/4") BHCS BOLT (33-11-0002) Issued/Revised: 05/22/13 800.458.5872 www.ultraplay.
uPLAY TODAY VINE CLIMBER 02-07-5008 Parts List DESCRIPTION VINE CLIMBER DECK MOUNTING BRACKET VINE CLIMBER EXTENSION POST-LONG VINE CLIMBER EXTENSION POST-SHORT FOOTER PLATE GRAB BAR TUBE CLAMP HARDWARE COMPLETE M10 x 20mm (3/4") BHCS BOLT M10 x 25mm (1") BHCS BOLT M12 LOCKWASHER M10 FLATWASHER M10 x 35mm (1 3/8") BHCS BOLT M10 LOCK NUT M8 x 25mm (1") BHCS BOLT M8 LOCKWASHER M8 LOCK NUT CLAMP RIVET QTY 1 1 2 2 2 2 4 1 3 4 4 7 2 5 12 4 8 4 PART NUMBER 02-07-0032 02-07-0085 02-07-0097 02-07-0098 02-07-0046
uPLAY TODAY VINE CLIMBER 02-07-5008 NOTE: THE VERTICAL POSITION OF THE GRAB BARS MUST BE A MINIMUM OF 38" ABOVE THE DECK. THE CLAMP POSITION CAN BE ADJUSTED HIGHER TO AVOID INTERFERENCE WITH OTHER CLAMPS. 7. Attach Tube Clamp to Upright using M8 x 25mm B.H.C.S. Bolt and M8 Lock Nut. Once all clamps are on and secure drill Ø1/4" hole through Clamp and Upright to install Clamp Rivet. See Detail 030. (Do not Install Clamp Rivet until entire unit is assembled) 8.
0 INCH 0 CM 1 2 3 2 1 4 3 5 6 7 5 4 8 9 10 11 12 6 13 14 15 VINE CLIMBER 02-07-5008 M8 x 25mm (1") BHCS BOLT (33-11-0103) GRAB BAR TUBE CLAMP UPRIGHT M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) M8 x 25mm (1") BHCS BOLT (33-11-0103) M8 LOCKWASHER (33-11-0301) 029 CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
0 INCH 0 CM 1 2 3 2 1 3 5 4 6 7 5 4 8 9 10 11 12 6 13 14 15 VINE CLIMBER 02-07-5008 DECK DECK MOUNTING BRACKET ROTOMOLD M10 FLATWASHER (33-11-0200) M10 x 25mm (1") BHCS BOLT (33-11-0003) M10 FLATWASHER (33-11-0200) ROTOMOLD EXTENSION POST M12 LOCKWASHER (33-11-0203) M12 LOCKWASHER (33-11-0203) 041 042 M10 x 25mm (1") BHCS BOLT (33-11-0003) Issued/Revised: 04/26/13 800.458.5872 www.ultraplay.
uPLAY TODAY WINDOW PANEL 02-07-5010 Parts List DESCRIPTION WINDOW PANEL HARDWARE COMPLETE M10 x 20mm (3/4") BHCS BOLT M12 LOCKWASHER M10 FLATWASHER M8 x 25mm (1") BHCS BOLT M8 x 55mm (2 3/16") BHCS BOLT M8 LOCK NUT M8 BARREL NUT CLAMP RIVET QTY 1 1 2 2 2 4 2 4 2 2 PART NUMBER 02-07-0019 33-12-0034 33-11-0002* 33-11-0203* 33-11-0200* 33-11-0103* 33-11-0110* 33-11-0500* 33-11-0501* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each *Items listed below Hardware Complete line are included
uPLAY TODAY WINDOW PANEL 02-07-5010 WINDOW PANEL (02-07-0019) 027 026 UNDERNEATH = INSTALLATION DETAIL FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY Issued/Revised: 03/26/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 5 4 3 6 7 5 4 8 9 10 11 12 6 13 14 15 WINDOW PANEL 02-07-5010 M8 x 25mm (1") BHCS BOLT (33-11-0103) M10 x 20mm (3/4") BHCS BOLT (33-11-0002) M12 LOCKWASHER (33-11-0203) M10 FLATWASHER (33-11-0200) M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) CLAMP RIVET (33-11-0700) DECK M8 x 25mm (1") BHCS BOLT (33-11-0103) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
uPLAY TODAY BARRIER PANEL 02-07-5011 Parts List DESCRIPTION BARRIER PANEL HARDWARE COMPLETE M10 x 20mm (3/4") BHCS BOLT M12 LOCKWASHER M10 FLATWASHER M8 x 25mm (1") BHCS BOLT M8 x 55mm (2 3/16") BHCS BOLT M8 LOCK NUT M8 BARREL NUT CLAMP RIVET QTY 1 1 2 2 2 4 2 4 2 2 PART NUMBER 02-07-0018 33-12-0034 33-11-0002* 33-11-0203* 33-11-0200* 33-11-0103* 33-11-0110* 33-11-0500* 33-11-0501* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each *Items listed below Hardware Complete line are include
uPLAY TODAY BARRIER PANEL 02-07-5011 BARRIER PANEL (02-07-0018) 027 026 UNDERNEATH = INSTALLATION DETAIL FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY Issued/Revised: 04/10/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 5 4 3 6 7 5 4 8 9 10 11 12 6 13 14 15 BARRIER PANEL 02-07-5011 M10 x 20mm (3/4") BHCS BOLT M12 LOCKWASHER (33-11-0002) (33-11-0203) M8 x 25mm (1") BHCS BOLT (33-11-0103) UPRIGHT M10 FLATWASHER (33-11-0200) M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) DECK 025 DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
uPLAY TODAY SHIP'S WHEEL PANEL 02-07-5012 Parts List DESCRIPTION SHIP'S WHEEL PANEL HARDWARE COMPLETE M10 x 20mm (3/4") BHCS BOLT M12 LOCKWASHER M10 FLATWASHER M8 x 25mm (1") BHCS BOLT M8 x 55mm (2 3/16") BHCS BOLT M8 LOCK NUT M8 BARREL NUT CLAMP RIVET QTY 1 1 2 2 2 4 2 4 2 2 PART NUMBER 02-07-0016 33-12-0034 33-11-0002* 33-11-0203* 33-11-0200* 33-11-0103* 33-11-0110* 33-11-0500* 33-11-0501* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each *Items listed below Hardware Complete line a
uPLAY TODAY SHIP'S WHEEL PANEL 02-07-5012 SHIP'S WHEEL PANEL (02-07-0016) 027 026 UNDERNEATH = INSTALLATION DETAIL FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY Issued/Revised: 04/12/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 5 4 3 6 7 5 4 8 9 10 11 12 6 13 14 15 SHIP'S WHEEL PANEL 02-07-5012 M8 x 25mm (1") BHCS BOLT (33-11-0103) UPRIGHT M10 x 20mm (3/4") BHCS BOLT (33-11-0002) M10 LOCKWASHER (33-11-0201) M8 LOCK NUT (33-11-0500) M10 FLATWASHER (33-11-0200) M8 LOCK NUT (33-11-0500) CLAMP RIVET (33-11-0700) 025 DECK M8 x 25mm (1") BHCS BOLT (33-11-0103) 026 DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
uPLAY TODAY GAME PANEL 02-07-5013 Parts List DESCRIPTION ACORN - LEAF PANEL HARDWARE COMPLETE M10 x 20mm (3/4") BHCS BOLT M12 LOCKWASHER M10 FLATWASHER M8 x 25mm (1") BHCS BOLT M8 x 55mm (2 3/16") BHCS BOLT M8 LOCK NUT M8 BARREL NUT CLAMP RIVET QTY 1 1 2 2 2 4 2 4 2 2 PART NUMBER 02-07-0020 33-12-0034 33-11-0002* 33-11-0203* 33-11-0200* 33-11-0103* 33-11-0110* 33-11-0500* 33-11-0501* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each *Items listed below Hardware Complete line are inclu
uPLAY TODAY GAME PANEL 02-07-5013 ACORN-LEAF PANEL (02-07-0020) 027 025 026 UNDERNEATH = INSTALLATION DETAIL FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY Issued/Revised: 04/11/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 3 5 4 6 7 5 4 8 9 10 11 12 6 13 14 15 GAME PANEL 02-07-5013 M10 x 20mm (3/4") BHCS BOLT (33-11-0002) M8 x 25mm (1") BHCS BOLT (33-11-0103) UPRIGHT M12 LOCKWASHER (33-11-0203) M10 FLATWASHER (33-11-0200) M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) CLAMP RIVET (33-11-0700) DECK 025 M8 x 25mm (1") BHCS BOLT (33-11-0103) THREADED INSERT DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
uPLAY TODAY BENCH PANEL 02-07-5014 Parts List DESCRIPTION QTY BENCH PANEL 1 4 PANEL CLAMP 1 HARDWARE COMPLETE 4 M8 x 30mm (1 3/16") BHCS BOLT 4 M8 LOCKWASHER 8 M8 x 25mm (1") BHCS BOLT 8 M8 LOCK NUT CLAMP RIVET 4 PART NUMBER 02-07-0015 02-07-0040 33-12-0031 33-11-0104* 33-11-0301* 33-11-0103* 33-11-0500* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete line are included with Hardware Complete Number Warning: During Installation, Hardware And Small
uPLAY TODAY BENCH PANEL 02-07-5014 PANEL CLAMP (02-07-0040) 025 038 BENCH PANEL (02-07-0015) FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY = INSTALLATION DETAIL Issued/Revised: 04/23/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 BENCH PANEL 02-07-5014 PANEL CLAMP ROTOMOLD M8 x 25mm (1") BHCS BOLT (33-11-0103) M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) M8 x 30mm (1 3/16") BHCS BOLT (33-11-0104) M8 LOCKWASHER (33-11-0301) 038 DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET. (33-11-0700) 025 Issued/Revised: 04/23/13 800.458.5872 www.ultraplay.
uPLAY TODAY ROOF 02-07-5015 Parts List DESCRIPTION ROOF HARDWARE COMPLETE M5 x 76mm (3") SELF-TAPPING SCREW QTY 1 1 4 PART NUMBER 02-07-0037 33-12-0036 33-11-0600* Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete line are included with Hardware Complete Number Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store Unused Parts Appropriately Until Assembly Is Completed.
uPLAY TODAY ROOF 02-07-5015 ROOF (02-07-0037) 037 UNDERNEATH = INSTALLATION DETAIL COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY FINISHED ASSEMBLY Issued/Revised: 04/22/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 ROOF 02-07-5015 ROOF M5 x 76mm (3") SELF-TAPPING SCREW (33-11-0600) UPRIGHT 037 Issued/Revised: 04/22/13 800.458.5872 www.ultraplay.
uPLAY TODAY BONE BRIDGE 02-07-5016 Parts List DESCRIPTION QTY 1 BONE BRIDGE 4 BRACKET HARDWARE COMPLETE 1 10 M10 x 25mm (1") BHCS BOLT M12 LOCKWASHER 6 14 M10 FLATWASHER M10 LOCK NUT 4 12 M8 x 25mm (1") BHCS BOLT 4 M8 LOCKWASHER M8 LOCK NUT 8 4 CLAMP RIVET PART NUMBER 02-07-0023 02-07-0024 33-12-0006 33-11-0003* 33-11-0203* 33-11-0200* 33-11-0400* 33-11-0103* 33-11-0301* 33-11-0500* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete line are included
uPLAY TODAY BONE BRIDGE 02-07-5016 BONE BRIDGE (02-07-0023) 029 UNDERNEATH 030 052 BRACKET (02-07-0024) 050 051 UNDERNEATH = INSTALLATION DETAIL FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY 05/07/13 800.458.5872 www.ultraplay.
0 INCH 1 0 CM 1 2 3 2 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 BONE BRIDGE 02-07-5016 M8 x 25mm (1") BHCS BOLT (33-11-0103) HANDRAIL TUBE CLAMP UPRIGHT M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) M8 x 25mm (1") BHCS BOLT (33-11-0103) M8 LOCKWASHER (33-11-0301) CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
0 INCH 0 CM 1 1 2 3 2 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 BONE BRIDGE 02-07-5016 BRACKET M12 LOCKWASHER (33-11-0203) BONE BRIDGE M10 FLATWASHER (33-11-0200) 052 M10 x 25mm (1") BHCS BOLT (33-11-0003) 05/07/13 800.458.5872 www.ultraplay.
uPLAY TODAY CRAWL TUNNEL w/ PANELS 02-07-5017 Parts List DESCRIPTION QTY 1 CRAWL TUNNEL w/ PANELS 1 HARDWARE COMPLETE 4 M10 x 20mm (3/4") BHCS BOLT 4 M12 LOCKWASHER 4 M10 FLATWASHER 8 M8 x 25mm (1") BHCS BOLT 4 M8 x 55mm (2 3/16") BHCS BOLT M8 LOCK NUT 8 M8 BARREL NUT 4 CLAMP RIVET 4 PART NUMBER 02-07-0021 33-12-0017 33-11-0002* 33-11-0203* 33-11-0200* 33-11-0103* 33-11-0110* 33-11-0500* 33-11-0501* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each *Items listed below Hardware Complete
uPLAY TODAY CRAWL TUNNEL w/ PANELS 02-07-5017 CRAWL TUNNEL w/ PANELS (02-07-0021) 025 027 026 UNDERNEATH = INSTALLATION DETAIL FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY 04/10/13 800.458.5872 www.ultraplay.
0 INCH 1 0 CM 1 2 3 2 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 CRAWL TUNNEL w/ PANELS 02-07-5017 PANEL CLAMP M8 x 25mm (1") BHCS BOLT (33-11-0103) M10 x 20mm (3/4") BHCS BOLT (33-11-0002) M12 LOCKWASHER (33-11-0203) M10 FLATWASHER (33-11-0200) M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) CLAMP RIVET (33-11-0700) DECK M8 x 25mm (1") BHCS BOLT (33-11-0103) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
uPLAY TODAY RAIN WHEEL w/TUBE CLAMP 02-07-5022 Parts List DESCRIPTION QTY RAINWHEEL CLAMP 1 1 PLASTIC INSERT METAL BUSHING 1 RAIN WHEEL 1 YELLOW PLASTIC CAP 1 1 HARDWARE COMPLETE M8 x 100mm (4") BHCS BOLT 1 1 M8 FLATWASHER M8 LOCK NUT 3 2 M8 x 25mm (1") BHCS BOLT CLAMP RIVET 1 PART NUMBER 02-07-0143 02-07-0094 02-07-0095 02-07-0012 02-07-0088 33-12-0035 33-11-0113* 33-11-0300* 33-11-0500* 33-11-0103* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete
uPLAY TODAY RAIN WHEEL w/TUBE CLAMP 02-07-5022 UPRIGHT RAINWHEEL TUBE CLAMP (02-07-0143) 030 = INSTALLATION DETAIL RAIN WHEEL (02-07-0012) 049 FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY Issued/Revised: 05/06/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 RAIN WHEEL w/TUBE CLAMP 02-07-5022 M8 x 25mm (1") BHCS BOLT (33-11-0103) UPRIGHT M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP INTO UPRIGHT TO INSTALL CLAMP RIVET.
uPLAY TODAY BASS DRUM w/TUBE CLAMP 02-07-5023 Parts List DESCRIPTION QTY BASS DRUM BRACKET 1 2 TUBE CLAMP 1 BASS DRUM HARDWARE COMPLETE 1 6 M8 x 25mm (1") BHCS BOLT 2 M8 LOCKWASHER 7 M8 LOCK NUT M8 x 20mm (3/4") BHCS BOLT 3 6 M8 FLATWASHER CLAMP RIVET 2 PART NUMBER 02-07-0091 02-07-0039 02-07-0013 33-12-0021 33-11-0103* 33-11-0301* 33-11-0500* 33-11-0102* 33-11-0300* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete line are included with Hardware C
uPLAY TODAY BASS DRUM w/TUBE CLAMP 02-07-5023 UPRIGHT 029 UNDERNEATH BASS DRUM BRACKET (02-07-0091) 030 053 TUBE CLAMP (02-07-0039) = INSTALLATION DETAIL BASS DRUM (02-07-0013) FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY Issued/Revised: 05/07/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 4 3 5 6 7 5 4 8 9 10 11 12 6 13 14 15 BASS DRUM w/TUBE CLAMP 02-07-5023 M8 x 25mm (1") BHCS BOLT (33-11-0103) BASS DRUM BRACKET TUBE CLAMP UPRIGHT M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) M8 x 25mm (1") BHCS BOLT (33-11-0103) M8 LOCKWASHER (33-11-0301) 029 CLAMP RIVET (33-11-0700) M8 x 25mm (1") BHCS BOLT (33-11-0103) DRILL THROUGH PRE-DRILLED HOLE IN CLAMP IN UPRIGHT TO INSTALL CLAMP RIVET.
uPLAY TODAY BONGO DRUMS 02-07-5024 Parts List DESCRIPTION BONGO DRUMS BRACKET BONGO DRUMS TUBE CLAMP MOUNTING BAR BONGO DRUMS HARDWARE COMPLETE M8 x 25mm (1") BHCS BOLT M8 BARREL NUT M8 x 20mm (3/4") BHCS BOLT M8 FLATWASHER M8 LOCK NUT M10 LOCKWASHER CLAMP RIVET QTY 1 1 1 1 1 4 1 2 6 5 3 1 PART NUMBER 02-07-0092 02-07-0056 02-07-0093 02-07-0014 33-12-0020 33-11-0103* 33-11-0501* 33-11-0102* 33-11-0300* 33-11-0500* 33-11-0201* 33-11-0700* Unless Otherwise Specified, All Units of Measure are Each Items lis
uPLAY TODAY BONGO DRUMS 02-07-5024 054 BONGO DRUMS TUBE CLAMP (02-07-0056) MOUNTING BAR (02-07-0093) 003 BONGO DRUMS (02-07-0014) 030 = INSTALLATION DETAIL FINISHED ASSEMBLY COMPONENTS SHOWN IN HIDDEN LINES ARE SOLD SEPARATELY Issued/Revised: 05/08/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 BONGO DRUMS 02-07-5024 M8 x 25mm (1") BHCS BOLT (33-11-0103) M8 x 20mm (3/4") BHCS BOLT (33-11-0102) BONGOS (02-08-0025) UPRIGHT M10 LOCKWASHER (33-11-0201) M8 FLATWASHER (33-11-0300) M8 LOCK NUT (33-11-0500) M8 LOCK NUT (33-11-0500) MOUNTING BAR (02-08-0126) M8 LOCK NUT (33-11-0500) BONGO SUPPORT BRACKET (02-08-0103) M8 FLATWASHER (33-11-0300) M8 FLATWASHER (33-11-0300) M8 LOCK NUT (33-11-0500) M8 FLATWASHER (33-11-
uPLAY TODAY 11' UPRIGHT, CLAMP, & FOOTER 02-07-5028 Parts List DESCRIPTION 3 1/2" UPRIGHT, 11' LG. UPRIGHT FOOTER HARDWARE COMPLETE M10 x 80mm (3 1/8") BHCS BOLT M10 BARREL NUT QTY 1 1 1 2 2 PART NUMBER 02-07-0001 02-07-0042 33-12-0026 33-11-0011* 33-11-0401* Unless Otherwise Specified, All Units of Measure are Each Items listed below Hardware Complete line are included with Hardware Complete Number Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children.
uPLAY TODAY 11' UPRIGHT, CLAMP, & FOOTER 02-07-5028 3-1/2" UPRIGHT, 11' LG. (02-07-0001) 063 UPRIGHT FOOTER (02-07-0042) FINISHED ASSEMBLY = INSTALLATION DETAIL Issued/Revised: 05/24/13 800.458.5872 www.ultraplay.
0 INCH 0 CM 1 2 3 2 1 3 4 5 6 7 5 4 8 9 10 11 12 6 13 14 15 11' UPRIGHT, CLAMP, & FOOTER 02-07-5028 UPRIGHT LARGE HOLE M10 BARREL NUT (33-11-0401) M10 x 80mm (3 1/8") BHCS BOLT (33-11-0011) TOP (2) HOLES USED FOR 12" ENGINEERED WOOD FIBER BOTTOM (2) HOLES USED FOR 2" POURED IN PLACE OR RUBBER TILES FOOTER 063 Issued/Revised: 05/24/13 800.458.5872 www.ultraplay.