Model: R5 Model: U3061806 Model: C5 Model: C7 Model: C3 Model: C12 Villa Video Door Phone
Remark Please follow the user manual for correct installation and testing. If there is any doubt please call our tech-supporting and customer center. Our company applies ourselves to reformation and innovation of our products. No further notice for any change. The illustration shown here is only for reference. If there is any difference please take the actual product as the standard. The product and batteries must be handled separately from household waste.
CATALOG Product description .................................................................... 1 Product appearance ................................................................... 1 Basic function .............................................................................. 7 Technical parameter ................................................................... 7 Product executive standard ..................................................... 8 Package contents.......................................
Product description Application:280SD is outdoor panel based on TCP/IP communication protocal, supporting digital video intercom and SIP communication protocol.
Model:280SD-C5(With metal surface) LED light Camera Speaker Call button Microphone Model:280SD-C5(With glass surface) LED light Camera Speaker Card swiping area Call button Microphone - 2-
Model:280AC-C5 Power indicator Card indicator Card swiping area Model:280SD-C7 Camera LED light Speaker Call button Microphone - 3-
Model:280SD-C3(with digital keypad) Light sensor Microphone Camera LED light Digital keypad Nameplate Call button Speaker Model:280SD-C3(with card) Light sensor Microphone LED light Camera Card swiping area Nameplate Call button Speaker - 4-
Model:280SD-C3 Light sensor Microphone LED light Camera Nameplate Call button Speaker Model:280SD-C12(with card) LED light Camera Speaker Card swiping area Call button Microphone - 5-
Model:280SD-C12(with card and nameplate) LED light Camera Speaker Nameplate Card swiping area Call button Microphone Model:280SD-C12(with nameplate) LED light Camera Speaker Nameplate Call button Microphone - 6-
Basic function ◇Call indoor monitor by one button; ◇Support IC/ID access control card; ◇IC/ID card information can be registered on outdoor panel. Registration information of max. 100,000 IC/ID cards can be stored ; ◇Support unlocking by Exit button and door magnetic detection; ◇Support LED light for night vision; ◇Support POE power supply. Technical parameter ◇Working voltage: DC12V ◇Rated power: 3W ◇Standby power: 1.
Product executive standard ◇ GB/T 18239-2000 "Genericspecificationforintegratedcircuitcardreader” ◇ GA/T 394-2002 "Specifications of access control system" Package contents Expansion tube Screw Basic operation 1. Call indoor monitor In standby mode, press the call button on outdoor panel to call indoor monitor. During the call, press the call button on outdoor panel again to end the call. If the call fails or indoor monitor is busy, outdoor panel will emit a beep. 2.
WEB settings Connect outdoor panel to PC through the switch. Input IP address of outdoor panel in the web browser of PC (The IP addresses of PC and outdoor panel must be on the same network segment. Default IP address is 192.168.68.90), then input user name and password (default user name is "admin" and the password is "123456") to enter into the following interface: 1.
DHCP: dynamic IP function. IP address: for the same system on the same network segment, IP address can not be repeated. Subnet mask: the original subnet mask is 255.255.255.0, which normally doesn't need to be changed.
System volume: adjust the system volume with 6 level for selection. Video size: 320x240, 640x480 or 1280x720. Call forwarding: the call can be made one by one or simultaneously. After the setup is completed, click the icon “Submit" to enable the settings. 3.Access Settings Click the icon "Access" on the left side to enter the interface as shown below: Unlock Timeout is used for controlling the unlocking time ranging from 1 to 9s. Unlock Delay refers to the delayed opening time ranging from 0 to 9s.
Then register the user card. The user shall swipe the admin card first. The system emits a beep. Then place the card to be registered near the swiping area within 10 seconds. When the system gives an indication tone, it means that the user card is registered successfully. When registering the user card, the card to be registered shall be swiped 10 seconds after the admin card is swiped. Once a user card is registered, it will postpone for 10 seconds.
5. Call Forwarding Click the icon "Forward" on the left side of the page to enter the interface as shown below: The room number can be bound with the telephone number. When a visitor calls but there is no answer within 25 seconds, the system will automatically forward the call to the phone. Specific steps are as follows: 1. Enter the room number first, then enter the phone number you want to bind; 2. To delete this account, check the box; 3.
Quick Call: Check the box to enable this function. It refers to the call to management center. Enter the SIP address of specified management center device in the box after URL. The device can be indoor monitor or SIP phone of other manufacturers. Check the box of Voice GW to enable voice gateway. The settings are as follows: 1. Connect LAN port of voice module to the computer through the switch, set the computer's IP address to 192.168.2.*, open IE browser, and enter http: //192.168.2.
7.Other Settings Click the icon "Others" on the left side of the page to enter the interface as shown below: Click Reboot to restart the system. 8.Logout Click the icon "Logout" on the left side. In next page, click the icon "Submit" to log out the system.
System connection diagram Terminal power CAT-5e+RVV2*1.0 Terminal power CAT-5e+RVV2*1.0 220V 220V network switch network switch 2F 2F CAT-5e CAT-5e Terminal power Terminal power 220V RVV2*1.0 1F 220V RVV2*1.0 1F network switch network switch Fiber transceiver RVV3*1.0 Fiber transceiver RVV3*1.0 Host Power Supply Host Power Supply 220V 220V RVV2*1.0 RVV2*1.
3 4 1 2 3 1 4 3 4 4 5 COM NC 6 7 EXIT DS Rs485 Power/Exit Button/Door Magnetic 5 1 2 3 Network Interface Power interface 1 2 +12V GND NO +12V GND 485+ 485 DS 3 2 2 1 EXIT GND DIN 4 Network Exit Button/Door Magnetic Rs485 Interface Interface +12V GND NO +12V GND 485+ 485 Wiring diagram of outdoor panel COM NC U3061806/R5 C3 Network Interface Power Peripheral Interface Network 12V GND 485+ 485- NO COM NC EXIT DS DIN +12V GND NO DC12V COM NC RJ45 C12 C5/C7 1
b. EXIT GND DIN DS Exit button Magnetic detection switch Exit Button/Door Magnetic +12V GND 485+ 485 +12V GND 485+ 485 RS485 interface RS485 equipment 2. Network Interface Connect to management center, indoor monitor or other network device through network switch. CAT-5e network interface 3.Power / Unlock Signal Output Connect power interface of outdoor panel to 12V DC power.
4.Switching Value Output Switching value output interface is available. Independent power supply for the lock is required. The electric lock can be connected in two ways including normally-open connection and normally-closed connection.
Installation instructions Model:U3061806 Appearance dimension drawing Installation diagram 38.6mm 170.5mm 111.0mm Screw Product size: 170.5*111*38.6mm Built-in Box D-R2 shield D- R2 Model:R5 Installation diagram Appearance dimension drawing 90.0mm 153.0mm CARD 24.
Model:C5 Installation diagram Appearance dimension drawing Product size: 160x99.5x47mm Built-in box size:151x94x45mm Trepanning size:153x96x50mm Built in Box Drain hole C5 Model:C7 Installation diagram Appearance dimension drawing Product size: 160x99.
Model:C3 Installation diagram Appearance dimension drawing Product size: 192x116x47mm Built-in box size:100X177X45mm Trepanning size:105x182x52mm Drain hole Built-in Box D-C3 Model:C12 Installation diagram Appearance dimension drawing 31 95 190 Product size: 190x95x31mm Built-in Box Rear Cover C12 - 22-
Model:C12 Installation diagram Appearance dimension drawing 27 95 190 Product size: 190x95x27mm Built-in box size:180X85X45mm Trepanning size:185x90x52mm Built in Box D-C12 Drain hole Installation notes: Wall 1450~1550mm [Suggestion]: During the installation, the display screen should be 1450~1550mm from the ground.
Troubleshooting Some common failures and troubleshooting methods are listed for your reference. In case of failure which cannot be repaired, do not disassemble or repair the product by yourself. Please contact the after-sales service department. When outdoor panel fails to call indoor monitor: a. When setting villa outdoor panel, please make sure building No. and unit No. of outdoor panel are the same as the ones of indoor monitor; b. Please check whether the network is connected; c.
Safety & Precautions Safety & Precautions To protect you and others from harm or protect your device from damage, please read the following information before using your device. Do not install equipment in the following areas: Do not install equipment in high temperature, humidity, near the magnetic field, such as generators, transformers or magnets, etc. Do not place the equipment near the heating items such as the electric heater or the liquid container.
IC Statement: This device complies with Industry Canada’s licence‐exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.