Quick Start Guide

More sensors can be connected.
3 PIN Port
3 PIN Port
Warning
1. Don't connect to the 6th port.
2. Each port supports up to 5
sensors in serial connection
Product Name: uKit Robot
Product Model: ERU Series
Quick start guide
www.ubtrobot.com
UBTECH ROBOTICS CORP LTD
UBTECH ROBOTICS CORP LTD
The UBTECH EDU app must first be downloaded and installed
for assembly.
① Main Control Box ① Motion Control
② Module connection ③ Connector installation and Removal Tips
压针齿线
压针齿线
P7 P8 P9 P10
Add: 16th and 22ndFloor,BlockC1,NanshanIPark, No.1001
XueyuanRoad,NanshanDistrict,Shenzhen, P.R.China
Web: www.ubtrobot.com
FCC ID: 2AHJX-UKITERU
DECLARATION OF CONFORMITY
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Product Name: uKit Robot
Product Model: ERU Series
Product Description: Input: 9.6V, 1A
Bluetooth Frequency range: 2402MHz-2480MHz,
Maximum Output Power: 1.06dBm
UBTECH ROBOTICS CORP LTD declares thatuKit Robot is in compliance with
Directive 2014/30/EU,2014/35/EU,2014/53/EU,2011/65/EU; Directive (EU)2015/863;
Directive EC/1907/2006.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ-
ment. This equipment should be installed and operated with a minimum distance of 20cm between
the radiator & your body. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT:
Please read all instructions before operating your product.
To be used under the direct supervision of an adult.
WARNING!
• The packaging must be retained since it contains important information.
• The battery charger used with the product is to be regularly examined for damage to the cord,
plug, enclosure and other parts, and in the event of such damage, they must not be used until the
damage has been repaired.
• The product is not to be connected to more than one power supply.
• The pruduct must be used with the recommended battery (Li-ion type rechargeable battery, rated
DC 7.4V).
• The battery is to be mounted with the correct polarity.
• The supply terminals, battery terminals and connectors are not to be short-circuited.
• Never connect more than 16 servo motors in total at the same time. Do not operate the product
during charging.
• Choking hazard - small parts inside. The product is not intended for children under 3 years old.
• The product must only be used with the recommended transformer (rated output DC 9.6V,1A-2A).
The transformer is not a toy.
• The product must be disconnected from the transformer before cleaning.
• Transformers and power supplies for products are not intended to be used as toys, and the use of
these products by children shall be under the full supervision of parents.
1.Software download and installation 2.Product components 3.Assembly and connection
③ Connectors, Parts, Fasteners and Wires
The decorative parts are added to the uKit robot
to give it more characters.
Fasteners look like buttons, and are used to connect various parts that contain holes.
Connectors are used to connect the various parts
that contain slots.