CL1TC-4 400W DVB-H Transmitter WEB Interface 6.4.11 Site The Site page allows the user to add information identifying the site, including the name of the site, address, contact information, etc. Each item is limited to 35 alphanumeric parameters.
CL1TC-4 400W DVB-H Transmitter 6.5 WEB Interface Alarms Menu The Alarms menu contains the following pull-down items (see Figure 6-25 below): • Alarm Properties • External Voltage Alarm Setting • Log Management • Alarm Log Figure 6-25 Alarms Menu The Alarms menu allows the user to set the properties of each alarm including system actions as well to view alarm and event logs. Product Manual, Rev.
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.5.1 Alarm Properties The first item in the Alarm Properties page is the Alarm Index. The Alarm Index box has a pull-down menu permitting the user to select a specific alarm from the list for configuration. The list of alarms along with a description of each alarm can be found in Section 10.
CL1TC-4 400W DVB-H Transmitter WEB Interface For each alarm, the user can set the following: Item Alarm Enabled Option OFF, ON Trap Notification on Alarm Used to control whether the selected alarm will be displayed (ON) or ignored (OFF). OFF, ON Integration Time Used to control whether the selected alarm will produce a SNMP trap notification. 0 to 360 sec Mute on Alarm Length of time an alarm condition is present before the alarm is declared.
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.5.2 External Voltage Alarm Setting The External Voltage Alarm Setting page allows the user to set the voltage threshold for each of the I/O port analog inputs (pins). Voltage 1 though Voltage 8 correspond to pins 1 though 8; pin 9 is ground. For example, the pin 6 settings (Voltage6 Trigger Polarity and Voltage6 Trigger Threshold) seen in Figure 6-27 will create an alarm if the pin 6 output voltage is greater than 2.0 VDC.
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.5.3 Log Management The Log Management page can be used to clear the alarm log and/or event log, change the order alarms appear in the logs and change the displayed alarm log. If the Alarm Log is configured not to display alarms in reverse, the most recent alarm will be at the bottom of the list. If the Alarm Log is configured to display alarms in reverse, the most recent alarm will be at the top of the list.
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.5.4 Alarm Log The Alarm Log lists the current alarms as well as all alarm log entries. Figure 6-29 Alarm Log Figure 6-30 Alarm Log (Log Displayed in Reverse) Product Manual, Rev.
CL1TC-4 400W DVB-H Transmitter 6.6 WEB Interface NMS Users Menu The NMS Users menu includes the User Properties menu (see the pull down figure below). The NMS Users menu sets the parameters required for an individual user to establish communications with the modulator via a SNMP Network Management System (NMS).
CL1TC-4 400W DVB-H Transmitter 6.7 WEB Interface System Parameters Menu The System Parameters menu displays the modulator access control, network and SNMP parameters. It is also used for system reset and upgrades.
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.7.1 Identification The Identification page allows the user to set the following identifiers: Item Site Name Site ID Option up to 35 alphanumeric characters up to 15 alphanumeric characters Table 6-16 Identification Parameters Figure 6-33 Identification Configuration 6.7.2 Access Control The Access Control page allows the user to set a password for the Web GUI interface.
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.7.3 Network Parameters The Network Parameters page allows the user to set the network parameters for the modulator. Note: The modulator must be reset following a change to any of the Network Parameters. Item Management IP Management Netmask Default Gateway Redundant Peer IP Option Standard Standard Standard Standard Second Etherport IP Not used for this application and should not be modified by the user. Standard IP address e.g., 172.20.25.
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.7.4 SNMP Parameters The SNMP Parameters page allows the user to configure the SNMP interface for the modulator. Item SNMP Traps On/Off SNMP Notification Type SNMP Trap Server IP Address Option OFF, ON Trap, Inform Standard IP address, e.g., 172.20.1.145 Table 6-19 SNMP Parameters Figure 6-36 SNMP Parameters 6.7.5 System Time The System Time page allows the user to set the system time.
CL1TC-4 400W DVB-H Transmitter WEB Interface Figure 6-37 System Time 6.7.6 Heartbeat Time The modulator has the capability to periodically send “Heartbeat” alarms and traps in order to show that it is still operating and that communication is still active. The user can set the Heartbeat Hours Start, Heartbeat Minute Start and repetition frequency for the heartbeat (Heartbeat Pace). Item Heartbeat Hour Start Heartbeat Minute Start Heartbeat Pace Option Range: 0 .. 24 Range: 0 ..
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.7.7 System Reset The modulator can be reset by setting the Modulator Reset pull down box to ”On” and selecting Submit. Item Modulator Reset Option OFF, ON Table 6-22 System Reset Parameters Figure 6-39 System Reset 6.7.8 User Configuration The User Configuration page allows the user to specify the address of the serial port used for machine-to-machine communication.
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.7.9 Download Config Files(s) The Download Config File(s) page allows the user to download files located on the modulator. Figure 6-41 Download Config Files(s) By clicking on the Download Parameter File box the user will see an operating system popup window, prompting the user to save the configuration file on their system: Figure 6-42 Download Pop-Up Window (Windows OS) Product Manual, Rev.
CL1TC-4 400W DVB-H Transmitter WEB Interface 6.7.10 Upgrade and Files Upload Procedure The Upgrade and Files Upload page allows the user to upgrade system software components such as: • Modulator Application • Linux Kernel (included in the Modulator Application) • Modulator FPGA • Up-converter Software The first step in the upgrade process is the selection of the proper upgrade file using the “Browse” button (see Figure 6-43).
CL1TC-4 400W DVB-H Transmitter WEB Interface As the upgrade starts a pop-up dialog will appear with the current upgrade process information. Figure 6-44 Upgrade Begin Pop-Up Once the upgrade is complete the pop up dialog will display a corresponding message. Figure 6-45 Upgrade Complete Pop-Up 6.7.11 List Uploaded Files The List Uploaded Files page provides a list of uploaded files on the modulator. Figure 6-46 List Uploaded Files Product Manual, Rev.
CL1TC-4 400W DVB-H Transmitter 7 7.1 CLI Command Line Interface (CLI) Introduction The transmitter can be controlled and monitored from the Command Line Interface (CLI) in addition to the Web GUI and front panel. The CLI is accessible from the USB port or via a Telnet session through the Ethernet management port. 7.2 Using the USB Port to access the CLI The modulator must be connected to a PC using a USB-to-USB cable.
CL1TC-4 400W DVB-H Transmitter 7.3 CLI Using Ethernet Port to access the CLI The modulator can be connected directly to a PC or through a hub/switch using an RJ-45 straight-through cable. The modulator and PC must be configured to be on the same IP network so that a connection can be established. A Telnet client can be opened from the “Start/Run” button on the PC. Enter the IP address assigned to the modulator followed by the number 26 – see below.
CL1TC-4 400W DVB-H Transmitter 7.5 CLI CLI Menu System The CLI contains a three level menu system where parameters can be viewed and changed. 7.5.1 Navigation Each menu has been assigned a numeric value for navigation purposes. To navigate through the CLI menu system, enter the number assigned to the desired menu. Depending on the menu accessed, the user may have the option to enter a sub-menu, or change a system parameter.
CL1TC-4 400W DVB-H Transmitter CLI 7.5.3 Menu Tree The CLI Menu tree is listed below with a total of 3 levels. Main Menu: 1. Status 2. Config 3. Alarms 4. NMS Users 5. System Parameters 6. Display Alarms 7. Firmware Upgrade r. Return to previous menu e. Exit CLI Enter selection: Main Menu 1. Status 2. Config 2. Config Level 2 1. Global Status 2. GPS Status 3. HPA 1. Modulator Mode 2. Transmission 2. Config 3. Input 2. Config 4. Output Product Manual, Rev. 1 Level 3 1. SFN 2. Config From Stream 3.
CL1TC-4 400W DVB-H Transmitter CLI Main Menu 2. Config Level 2 4. Output 2. Config 2. Config 2. Config 5. RF Channels 6. User RF Channels 7. Non-Linear Precorrector 2. Config 8. Linear Precorrector 2. Config 9. HPA Control 2. Config 10. GPS 2. Config 11. Site 3. Alarms 1. Alarm Properties 3. Alarms 2. External Voltage Alarm Setting 3. Alarms 3. Log Management Product Manual, Rev. 1 93 Level 3 9. Base Frequency 10. Base Channel Select RF Channel Select RF Channel 1. NLP State 2.
CL1TC-4 400W DVB-H Transmitter CLI Main Menu 4. NMS Users Level 2 1. User Properties Level 3 1. User Index 2. Username 3. Authorization Type 4. Auth. Password 5. Priv Type 6. Priv. Password 1. Site Name 2. Site ID Enter Web Password 5. System Parameters 5. System Parameters 5. System Parameters 1. Identification 5. System Parameters 4. SNMP Parameters 5. System Parameters 5. System Time 5. System Parameters 6. Heartbeat Time 5. System Parameters 5. System Parameters 6. Display Alarms 7.
CL1TC-4 400W DVB-H Transmitter CLI 7.5.3.1 Status Sub-menu Status: 1. Global Status 2. GPS Status 3. HPA r. Return to previous menu e. Exit CLI Enter selection : Status Sub-menu 1. Global Status Description Displays general status information for network management, alarms, modulation, transmitter output and reflected power values as well as transmitter frequency. Displays detailed GPS information such as site coordinates, altitude, GPS PLL and 3D fix status and satellite tracking.
CL1TC-4 400W DVB-H Transmitter Config Sub-menu CLI Sub-menu Selectable Parameters 1. Modulator Mode 0. 1. 2. 3. 4. 0. 1. Normal CW Test 1(Carriers Removed) Record Playback OFF ON 2. Transmission 1. SFN 2. Transmission 2. Config From Stream 0. ON 1. OFF 2. Transmission 3. Fixed Delay 0. OFF 1. ON 2. Transmission 2. Transmission 4. Input_Output Fixed Delay 5. MIP Time Offset Function Range: 13000 .. 1000000 µsec 0. OFF 1. ON 2. Transmission 6. MIP Frequency Offset Function 0. OFF 1. ON 2.
CL1TC-4 400W DVB-H Transmitter CLI Config Sub-menu Sub-menu Selectable Parameters 2. Transmission 2. Transmission 3. Input 18. Transmitter ID 19. Local Delay Offset 1. Selected Input 3. Input 2. IP Input Interface Range: 0 .. 100 Range: -500000 .. 500000 0. A 1. B 2. Auto 3. IP 0. Ethernet 2 1. Ethernet 1 3. Input 3. Input Stream Dst IP Range: 0.0.0.0 .. 255.255.255.255 3. Input 3. Input 4. Input Stream Dst Port 5. FEC Mode Range: 1025 .. 65535 0. None 1. Column Only 2. Column+Row 3.
CL1TC-4 400W DVB-H Transmitter CLI Config Sub-menu Sub-menu Selectable Parameters 8. Linear Pre-corrector 2. LP Profile 0 .. 9 9. HPA Control 9. HPA Control 1. RF Output Power Level 2. Transmitter Operating Mode 10. GPS 1. Max GPS Holdover Time, min 2. Update System Clock from GPS Range: 46.00 .. 56.00 dBm 0. Standby 1. Broadcast 2. Manual Range: 0 .. 65535 10. GPS 10. GPS 3. System Timezone 11. 11. 11. 11. 11. 11. 11. 11. 1. 2. 3. 4. 5. 6. 7. 8.
CL1TC-4 400W DVB-H Transmitter CLI 7.5.3.3 Alarms Sub-menu Alarms: 1. Alarm Properties 2. External Voltage Alarm Setting 3. Log Management r. Return to previous menu e. Exit CLI Enter selection : Alarms Sub-menu Sub-menu Selectable Parameters 1. Alarm Properties 1. Alarm Properties 1. Alarm Index 2. Alarm Enabled 1. Alarm Properties 3. Trap Notification on Alarm See Table 10-1 0. OFF 1. ON 0. OFF 1. ON 1. Alarm Properties 1. Alarm Properties 4. Integration Time 5.
CL1TC-4 400W DVB-H Transmitter CLI 2. External Voltage Alarm Setting 2. External Voltage Alarm Setting 2. External Voltage Alarm Setting 2. External Voltage Alarm Setting 2. External Voltage Alarm Setting 3. Log Management 12. Voltage6 Trigger Threshold Range: 0 .. 10 13. Voltage7 Trigger Polarity 0. < 1. > Range: 0 .. 10 1. Clear Alarm Log 0. No 1. Yes 3. Log Management 2. Logs Display in Reverse 0. No 1. Yes 3. Log Management 3. Log to Display 0. Transient Log 1. Alarm Log 14.
CL1TC-4 400W DVB-H Transmitter CLI 7.5.3.5 System Parameters Sub-menu System Parameters: 1. Identification 2. Access Control 3. Network Parameters 4. SNMP Parameters 5. System Time 6. Heartbeat Time 7. System reset r. Return to previous menu e. Exit CLI Enter selection: System Parameters Sub-menu 1. Identification 1. Identification 2. Access Control 3. Network Parameters Sub-menu Selectable Parameters 1. Site Name 2. Site ID Web Password 1.
CL1TC-4 400W DVB-H Transmitter CLI 7.5.3.6 Display Alarms Sub-menu This Sub-menu simply displays any active alarms. See below as an example: Enter Selection : 6Alarms: No Input Data HPA Controller Comm Err 7.5.3.7 Firmware Upgrade This Sub-menu allows the user to enter a URL address from which the transmitter can obtain a firmware upgrade. Enter URL: Product Manual, Rev.
CL1TC-4 400W DVB-H Transmitter 8 8.1 Modulator Front Panel Modulator Front Panel Interface Introduction The front panel system includes both Status Displays where important parameters are prominently displayed and the four-level Config Menu system where system parameters can be entered. A picture of the modulator front panel is shown below.
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel The “current” menu item is always shown in capitalized format with “< >” brackets. If there are more menu items than the LCD can display, three (3) dots are shown in the lower right position – see Example A. Example A ---------------------------------------DVB-TH L-Band TX Alarms NMS Users System Pa...
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel Example E ---------------------------------------Web Password = admin admin ---------------------------------------- 8.2.2 Configuring Parameters 8.2.2.1 Selection of Enumerated Values ---------------------------------------Modulator Mode = Normal [Normal] CW Test 1(Carriers Removal... ---------------------------------------(the square brackets flash at approx. 2 Hz) The current value is shown as the first item in the list, in square brackets.
CL1TC-4 400W DVB-H Transmitter EXECUTE Modulator Front Panel Completes editing. Note 1: If a configurable numeric item has a minimum and/or maximum value, the user cannot modify the value below the minimum or above the maximum. Note 2: Incrementing one character above ‘9’ will change this character to ‘0’ and will increment the next character to the left by one (“carry-on digit”).
CL1TC-4 400W DVB-H Transmitter 8.3 Modulator Front Panel Modulator Boot-up The user will see the following displays in sequence. ---------------------------------------Front Panel v1.22 Loading......
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel Status Display d - this window displays the software versions as seen below: ---------------------------------------DVB-TH FPGA: 5889 CPLD: 40 Kern: 3037 Soft: 2376 d ---------------------------------------Status Display e - this window displays the active alarms as seen below: ---------------------------------------Alarms: 2 alarms No Input Data e ---------------------------------------If more than one alarm is active, this window will automatically be
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel The start point in the Config Menu is: ---------------------------------------DVB-TH L-Band TX Alarms NMS Users System Pa... ---------------------------------------The full list of the level 1 menu items are: • Config • Alarms • NMS Users • System Parameters There are a total of 3 menu levels in the Config Menu chain. Use the left e and right f buttons to navigate between different sub-menu items.
CL1TC-4 400W DVB-H Transmitter Level 1 Config Modulator Front Panel Level 2 Level 3 •Constellation •Guard Interval •Interleaver Flag •Time Slice Indicator, HP •MPE-FEC Flag, HP •Cell Id •Transmitter ID •Local DelayOffset SFN Mode (Config From Stream On) •SFN •Config From Stream •Fixed Delay •Input_Output Fixed Delay •MIP Time Offset Function •MIP Frequency Offset Function •MIP Power Function •MIP CellId Function •Hierarchical Mode •Cell Id •Transmitter ID •Local DelayOffset •Selected Input •IP Input Int
CL1TC-4 400W DVB-H Transmitter Level 1 Config Config Config Level 2 RF Channels User RF Channels Non-Linear Precorrector Config Linear Precorrector Config HPA Control Config GPS Config Site Alarms Alarm Properties Alarms External Voltage Alarm Setting Alarms Log Management NMS Users [e] User Properties Product Manual, Rev.
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel Level 1 System Parameters System Parameters System Parameters Level 2 Identification Level 3 •Site Name •Site ID •Web Password System Parameters SNMP Parameters System Parameters System Time System Parameters Heartbeat Time System Parameters System Parameters System Reset •Management IP •Management Netmask •Default Gateway •Redundant Peer IP •Second Etherport IP •Second Etherport Netmask •SNMP Traps On/Off •SNMP Notification Type •SNMP Trap S
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel 8.7.1 Config x Modulator Mode ---------------------------------------Config, Modulator Mode ---------------------------------------The options are: Item Modulator Mode Option Normal, CW, Test1 (Carriers Removal), Record , Playback 8.7.2 Config xTransmission ---------------------------------------Config, Transmission Config From Stream Fixed Delay...
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel SFN Mode Item SFN Config From Stream Fixed Delay Input_Output Fixed Delay Hierarchical Mode IFFT Coderate Constellation Guard Interval Interleaver Flag Time Slice Indicator, HP MPE-FEC Flag, HP Cell ID Transmitter ID Local Delay Offset Option OFF, ON ON, OFF OFF, ON Range: 13000 μsec .. 1 second None, aEq1, aEq2, aEq4 2k, 8k, 4k 1/2, 2/3, 3/4, 5/6, 7/8 QPSK, 16 QAM, 64 QAM 1/32, 1/16, 1/8, 1/4 OFF, ON OFF, ON OFF, ON Range: 0 .. 65535 Range: 0 ..
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel 8.7.3 Config xInput ---------------------------------------Config, Input IP Input Interface ... ---------------------------------------Shortcut: To directly reach this menu Press EXECUTE from Status Display b The options are: Item Selected Input IP Input Interface Input Stream Dst IP Input Stream Dst Port FEC Mode IP Input Buffer Depth Selection A, B, Auto, IP Ethernet 1, Ethernet 2 Standard IP address: 0.0.0.0..255.255.255.
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel SFN Mode (with Config From Stream On) Item Mute ON/OFF Spectrum Inversion Window Enable External Amplifier Gain RF Output Frequency RF Power Level RF Channel Grid Base Frequency Base Channel Selection OFF, ON OFF, ON OFF, ON Range: 0.0.. 6553.5 dB Range: 167000000 .. 167500000 Hz Range: -10.0 .. 0.0 dBm DVBT UHF 8M 474-858 MHz, User Defined Range: 167000000 .. 167500000 Hz Range: 1 .. 200 8.7.
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel 8.7.8 Config xLinear Precorrector ---------------------------------------Config, Linear Precorrector LP Profile ---------------------------------------The options are: Item LP State LP Profile Selection OFF, ON A selection of different LP profile files 8.7.9 Config xHPA Control ---------------------------------------Config, HPA Control Transmitter O...
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel 8.7.11 Config x Site ---------------------------------------Config, Site Contact Informat... ---------------------------------------The options are: Item System Description Contact Information System Location Site Address Line 1 Site Address Line 2 Site Address Line 3 Site Address Line 4 Site Notes 8.
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel To select a specific alarm to set its properties in other menus the user must first set the Alarm Index value in the Alarm Index sub-menu screen. Upon entering the Alarm Index menu the user will see: ---------------------------------------Alarm Index = 0 [ Modulator Restarted] Heartbeat ... ---------------------------------------The Alarm Index menu lists all 66 alarms available in the system, with index values from 0 to 65.
CL1TC-4 400W DVB-H Transmitter 8.9 Modulator Front Panel NMS Users ---------------------------------------DVB-TH L-Band TX, NMS Users ---------------------------------------The additional menu items for this sub-menu are: • User Properties 8.9.1 NMS Users x User Properties ---------------------------------------NMS Users, User Properties Username Authorization...
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel 8.10.1 System Parameters x Identification ---------------------------------------System Parameters, Identification Site ID ---------------------------------------The additional menu items for this sub-menu are: Item Site Name Site ID Option up to 35 alphanumeric characters up to 15 alphanumeric characters 8.10.
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel Note: The modulator must be reset following a change to any of the Network Parameters. 8.10.4 System Parameters x SNMP Parameters ---------------------------------------System Parameters, SNMP Parameters SNMP Trap Server ...
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel 8.10.7 System Parameters x System Reset ---------------------------------------System Parameters, System Reset ---------------------------------------The additional menu items for this sub-menu are: Item Modulator Reset Option OFF, ON 8.10.
CL1TC-4 400W DVB-H Transmitter Modulator Front Panel 8.11 Config Menu Shortcuts Config x Transmission Press EXECUTE from Status Display a ---------------------------------------Config, Transmission Config From Stream Fixed Delay... ---------------------------------------- Config x Input Press EXECUTE from Status Display b ---------------------------------------Config, Input IP Input Interface ...
CL1TC-4 400W DVB-H Transmitter SNMP 9 SNMP The transmitter supports a SNMP interface for remote management of the transmitter via a SNMP Network Management System (NMS). Refer to sections 6.7.4 and 6.6 as to how to use the web interface to configure the SNMP interface and set up a NMS user account. Once the SNMP interface is established it is possible to use standard SNMP Network Managers (e.g., SNMPc, HP OpenView etc.) or a custom SNMP Network Manager for SNMP access.
CL1TC-4 400W DVB-H Transmitter Alarms 10 Alarms 10.1 Alarm List This section lists all system alarms available for the CL1TC-4 transmitter. Each alarm is described along with associated events and triggering conditions. The complete set of 66 alarms is listed below: 0. Modulator Restarted 1. Heartbeat 2. Exciter Temperature Fault 3. GPS Antenna Undercurrent 4. GPS Antenna Overcurrent 5. GPS Quality Low 6. GPS Comm Error 7. No Input Data 8. LP No Input Data 9. 10 MHz Reference Loss 10.
CL1TC-4 400W DVB-H Transmitter Alarms 10.2 Informative Alarms Informative alarms are event alarms, they have no alarm Begin/End conditions. 10.2.1 Modulator Restarted A transient Informative alarm; sent at system boot time. 10.2.2 Heartbeat A periodic Informative alarm; sent periodically at an interval determined by the system “Heartbeat Pace” parameter. The Heartbeat Pace parameter can be set via SNMP or through the modulator’s Web-GUI and Command Line interfaces. 10.3 Temperature Sensor Faults 10.3.
CL1TC-4 400W DVB-H Transmitter Alarms NOTE: The transmitter output is automatically muted as a result. Transmission is restored when the alarm is cleared. 10.4 GPS Alarms Please note that the internal GPS receiver is located on the modulator board. 10.4.1 GPS Comm Error GPS Comm Error - set when communications with the GPS receiver has failed. 10.4.2 GPS Antenna Undercurrent GPS Antenna Undercurrent – set when the antenna current value is low (antenna open). 10.4.
CL1TC-4 400W DVB-H Transmitter Alarms 10.5 Modulator Alarms Also see GPS alarms for the internal GPS. For the modulator temperature alarm see section 10.3. 10.5.1 10 MHz Reference Loss 10 MHz Reference Loss - Loss of 10 MHz Reference from GPS. This alarm is only raised if the 10 MHz reference is completely lost which is more likely to occur if there is a hardware failure.
CL1TC-4 400W DVB-H Transmitter Alarms 10.5.6 Mega Frame Loss Mega Frame Loss - set when the modulator cannot detect valid mega frames in the input stream. MIP packets are used to define the mega frame structure for DVB-T/H and the alarm is raised when MIP packets are not detected in the input stream or are invalid. Note: This alarm is only reported in SNF mode and is factory configured to mute the modulator. 10.5.
CL1TC-4 400W DVB-H Transmitter Alarms 10.5.12 Output Bitrate Is Out Of Limit Output bit rate is out of limit - a hardware failure alarm set when the output bit-rate is 10% higher or lower than the ideal bit rate corresponding to the selected mode. Note: This alarm is only reported in SNF mode and is factory configured to mute the modulator. 10.5.
CL1TC-4 400W DVB-H Transmitter Alarms 10.5.18 IP Input Column FEC Error IP Input Column Fec Error - set when the IP input column FEC packet format is incorrect. 10.5.19 IP Input Row FEC Error IP Input Row Fec Error - set when the IP input row FEC packet format is incorrect. 10.5.20 Upconverter Communication Error Up Converter Communication Error - set when communications with the Upconverter has failed. Note: The alarm is hard coded to mute the modulator in SFN and MFN mode.
CL1TC-4 400W DVB-H Transmitter Alarms 10.5.23 External Voltage 1 External Voltage 1 - set when the I/O port pin 1 voltage is greater than or less than the user defined value. 10.5.24 External Voltage 2 External Voltage 2 - set when the I/O port pin 2 voltage is greater than or less than the user defined value. 10.5.25 External Voltage 3 External Voltage 3 - set when the I/O port pin 3 voltage is greater than or less than the user defined value. 10.5.
CL1TC-4 400W DVB-H Transmitter Alarms 10.6 High Power Amplifier (HPA) Alarms and Warnings When a critical alarm occurs (except for thermal shutdown) the HPA will wait several seconds then try to re-start. If the critical alarm causes the HPA to shutdown again, the procedure will be repeated. After three repeated failures, within approximately 50 seconds, the HPA will stay in shutdown mode.
CL1TC-4 400W DVB-H Transmitter Alarms 10.6.5 HPA Reflected Power Err HPA Reflected Power Err (Critical) 47.0 dBm HPA Reflected Power Err - set when the reflected power reaches 47.0 dBm. NOTE: Automatic HPA shutdown is initiated by the HPA when the critical level is reached and a RF Switch Fault alarm is raised. The Web-GUI interface has no control over this action. 10.6.6 HPA Input Warning HPA Input Warning – set when the input power is less than -5.0 dBm.
CL1TC-4 400W DVB-H Transmitter Alarms 10.6.9 HPA Current Misbalance Warning HPA Current Misbalance Warning - set when the lowest current (A) reading on one of the power modules is less than 20% of the highest current (A) reading on one of the power modules. NOTE: The maximum output power level of the HPA will be limited to 53 dBm if a HPA Current Misbalance Warning alarm occurs. The Web-GUI interface has no control over this action.
CL1TC-4 400W DVB-H Transmitter Alarms 10.6.14 Power Module 2 Current Fault Power Module 2 Current Fault (Critical) 14.0 A Power Module 2 Current Fault – set when the power module 2 current reaches 14.0 A. NOTE: Automatic HPA shutdown is initiated by the HPA when the critical levels are reached and a HPA Failure alarm is raised. The Web-GUI interface has no control over this action. 10.6.15 Power Module 3 Current Fault Power Module 3 Current Fault (Critical) 14.
CL1TC-4 400W DVB-H Transmitter Alarms 10.6.19 HPA Power Supply 1 Fault HPA Power Supply 1 Fault (Critical) Low High 27.0 VDC 32.0 VDC HPA Power Supply 1 Fault – set when HPA power supply 1 DC voltage is out of the HPA allowable range and has reached the critical limits. NOTE: Automatic HPA shutdown is initiated by the HPA when the critical level is reached and a HPA Failure alarm is raised. The Web-GUI interface has no control over this action. 10.6.
CL1TC-4 400W DVB-H Transmitter Alarms 10.7 HPA I/O Serial Port Alarms 10.7.1 Door Opened Note: Door Opened is not used for this application. For the cabinet door alarm, please refer to section 10.5.28. 10.7.2 Fire Alarm Note: Fire Alarm is not used for this application. For the smoke detector alarm, please refer to section 10.5.29. Product Manual, Rev.
APPENDIX A: CL1TC-4 DVB-H L-Band Transmitter System and Drawers Drawings and Parts Lists
CL1TC-4 400W DVB-H Transmitter Appendix A: System & Drawers Drawings and Parts List CL1TC-4 DVB-H L-Band Transmitter System Drawing List CL1TC-4 Transmitter System w/Digital Modulator (Consists of one DVU 5000 Modulator Drawer driving one L-Band Amplifier Drawer) CL1TC-4, Interconnect .............................................................................1316822 CL1TC-4, AC Block Diagram .....................................................................
1 2 3 4 5 6 UBS P/N MFR 50461-01 59220-01 54515-01 UBS UBS UBS 50805-03 UBS 56871-01 59216-01 56829-01 54577-01 59215-01 59219-01 UBS UBS UBS UBS UBS Rear Panel 59217-01 UBS 1 1 59218-01 UBS 1 59216-02 UBS 2 90863-43G PCA Universal Modulator 90446-02 KEYPAD A 50461-01 54515-01 84149R DISPLAY Cable Modulator-Display J2 J13 J1 59215-01 Cable RF GPS Antenna J1 JP1-1 A JP1-2 K X20 57532-02 59216-01 Cable RF Modulator L Band Amplifier ASSY X15 X1 RF IN Cable RF Modulat
8 7 4 5 6 3 17.50 REV. DESCRIPTION 01 FIRST RELEASE ECO # DATE APPROVED 06/05/2013 02 ADD ITEM 35 10/06/2013 03 REPLACED ITEM 35 08/07/2013 21 20 32 D PRINTED ON: July-08-13 REVISIONS WARNING, THIS DRAWING AND ITS CONTENTS ARE PROPERTY OF UNIQUE BROADBAND SYSTEMS INC, AND SHALL NOT BE CIRCULATED OR REPRODUCED WITHOUT THE WRITTEN PERMISSION OF UNIQUE BROADBAND SYSTEMS INC. D 31 29 2.619 3 33 20.50 C 18.625 C 35 34 B 23 14 7.
8 7 4 5 6 3 July-08-13 2 WARNING, THIS DRAWING AND ITS CONTENTS ARE PROPERTY OF UNIQUE BROADBAND SYSTEMS INC, AND SHALL NOT BE CIRCULATED OR REPRODUCED WITHOUT THE WRITTEN PERMISSION OF UNIQUE BROADBAND SYSTEMS INC. 10 31 D D 24 22 13 C C 29 8 25 35 1 18 7 33 19 4 B B 30 22 12 A REAR PANEL SILK SCREEN DWG 56829-01 CAD GENERATED DRAWING DO NOT MANUALLY UPDATE OR SCALE 27 10 28 17 APPROVALS DRAWN NIMAL.D DATE TITLE 243 CHECKED RESP ENG SIZE B Q.A.
1 2 3 4 5 REV.
FAN 85103 3 4 J2-6 +12VDC PITB?01 PITB?01 J2-3 RTN VDC J2-4 RTN VDC PITB?02 PITB?02 TB6 PITB?01 PITB?01 NL3NL4 J2-2 +5 VDC J2-1 +5 VDC PITB?02 PITB?02 TB7 75088R Power Supply 60W 5/12 VDC GND A COR1 R1 PIR102 15 Ohm 31471R PIR101 84038 LED Indicator GREEN Back Plate Back Plate PIF301 PIF302 85102 COF5 F5 FAN 85102 COF6 F6 FAN PIF501 PIF502 85102 LED Indicator AC Power Supply 59191-01 85102 PIF401 PIF402 59189-01 COTS3 TS3 PITS301 1 2 3 PITS302 PITS303 1 2 GND COD1 D1 1 2 PI
1 2 3 4 5 REV.
1 2 3 4 5 REV. 90945-01 Current Monitoring 1 J2-1 Power Supply 1 PCA Temperature Sensor 1 J2-2 A Current Monitoring 2 J2-3 Temperature Sensor 2 J2-4 J2-5 J2-4 J2-3 J2-2 J2-1 J2-5 J2-6 Temperature Sensor 3 J2-7 Voltage Monitoring 1 J2-8 GND 12C interface. SCL. J2-10 PITS101 Voltage Monitoring PITS102 Enable Power supply PITS103 12C interface. SDA.
1 2 3 4 5 REV.
1 2 3 4 5 REV.
8 7 4 5 6 3 2 WARNING, THIS DRAWING AND ITS CONTENTS ARE PROPERTY OF UNIQUE BROADBAND SYSTEMS INC, AND SHALL NOT BE CIRCULATED OR REPRODUCED WITHOUT THE WRITTEN PERMISSION OF UNIQUE BROADBAND SYSTEMS INC. August-06-13 REVISIONS REV.
8 7 4 5 6 3 2 WARNING, THIS DRAWING AND ITS CONTENTS ARE PROPERTY OF UNIQUE BROADBAND SYSTEMS INC, AND SHALL NOT BE CIRCULATED OR REPRODUCED WITHOUT THE WRITTEN PERMISSION OF UNIQUE BROADBAND SYSTEMS INC. August-06-13 REVISIONS 8.72 4 REV. DESCRIPTION 01 FIRST RELEASE ECO # DATE APPROVED 17 D D 24 F F 23 18.99 C C 30.80 B B A A SECTION 16 F-F UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES.TOLERANCES ARE: DECIMALS ANGLES .XX ± .02 ± 0.5° .XXX ± .