Enterprise Security Gateway and Network Appliance with 10G SFP+ Model: UDM-Pro
Introduction Thank you for purchasing the Ubiquiti® UniFi® Dream Machine Pro. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents UniFi Dream Machine Pro Power Cord Rack-Mount Bracket Screws Brackets (Qty. 2) (Qty. 8) Cage Nuts (Qty. 4) Security Screw Mounting Screws (Qty. 4) 2.5" HDD Screws (Qty. 4) Rubber Feet (Qty.
Hardware Overview LEDs 1 2 3 5 4 6 7 8 9 10 System LED Color State Status Bootup Animation Initializing White Solid Device is ready to be configured Flashing Device is booting up Device is initializing/deinitializing Heartbeat Firmware update in process Blue Solid Device is configured and ready Slow Flashing Client connected to device via Bluetooth (BLE) Off/White/ Flashing Blue Device is in recovery mode.
RJ-45 Speed/ Link/Activity LED (Ports 1 - 9) SFP+ Speed/ Link/Activity LED (Ports 10 - 11) State Status Off No Link Amber Link Established at 10/100 Mbps Flashing Indicates Activity Green Link Established at 1 Gbps Flashing Indicates Activity Off No Link Green Link Established at 1 Gbps Flashing Indicates Activity White Link Established at 10 Gbps Flashing Indicates Activity Item Description HDD Bay Install a 3.5" or 2.5" HDD (not included) to use the device as an NVR for UniFi Protect.
Item Description Reset Button Resets to factory defaults. The device should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the LED starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the device will automatically reboot. 11 12 13 Item Description USP RPS LED Reserved for future use. USP RPS Input Reserved for future use. Power Connect the included Power Cord to the Power port.
Installation Requirements • Phillips screwdriver • Standard-sized, 19" wide rack with a minimum of 1U height available • For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use. • For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
2. 3.
4.
OR
5.
6.
Hardware Installation 1. 2.
Connecting Power
Connecting to the Internet For information about compatible fiber SFP modules, visit: ubnt.link/UniFi_SFP_DAC_Compatibility 1.
DDM 20KM m SM/SC /Rx1310n 05 1000Mbps Tx1550nm
Connecting to the LAN 05 1. 05 2.
05 3. DDM 20KM m s SM/SC /Rx1310n 1000Mbp Tx1550nm 05 05 4.
Configuration You have the following options: • Enable Bluetooth on your mobile device and use the UniFi Network app. • Use a computer connected to the UDM-Pro on a LAN port. Go to “Chrome Instructions”. UniFi Network App 1.
2. 1.5 m 1.5 m 3. Follow the on-screen instructions.
Chrome Instructions Use the Chrome web browser to set up your device. 1. Ensure that your host system is on the same Layer 2 network as the UDM-Pro. 2. Launch the Chrome web browser and go to https://setup.ui.com https://setup.ui.com 3. Follow the on-screen instructions of the Setup Wizard. After you run the UniFi Setup Wizard, a login screen will appear for the UniFi Network Controller management interface. Enter the Username and Password that you created in the UniFi Setup Wizard. Then click Sign in.
Specifications UDM-Pro Dimensions Weight With Mount Brackets Interfaces Networking Management Max. Power Consumption Power Method Power Supply Supported Voltage Range Display 442.4 x 43.7 x 285.6 mm (17.42 x 1.72 x 11.24") 3.90 kg (8.60 lb) 3.99 kg (8.80 lb) (8) 10/100/1000 RJ45 LAN Ports (1) 10/100/1000 RJ45 WAN Ports (1) 1/10G SFP+ LAN Port (1) 1/10G SFP+ WAN Port Ethernet In-Band (1) Bluetooth BLE 33W (1) Universal AC Input, 100 to 240VAC (1) RPS DC Input Internal 50W/12V 100 - 240VAC 1.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty ui.com/support/warranty The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1.
ISED Canada CAN ICES-3(A)/NMB-3(A) This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter (IC: 6545A-UDMPRO) has been approved by ISED Canada.
Australia and New Zealand Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. Brazil Nota: Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI декларира, че това устройство UDM-Pro е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/53/EC, 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: ui.
Italiano [Italian] Con la presente, UBIQUITI, dichiara che questo dispositivo UDM-Pro, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/53/UE, 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: ui.
Online Resources Support help.ui.com Community community.ui.com Downloads downloads.ui.com Ubiquiti Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2019 Ubiquiti Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, and UniFi are trademarks or registered trademarks of Ubiquiti Inc. in the United States and in other countries. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries.