802.
Package Contents UniFi AP AC HD Base Mount Plastic Ties (Qty. 2) PoE Adapter Screws (Qty. 2) Power Cord Screw Anchors (Qty. 2) Installation Requirements • Phillips screwdriver • Drill and drill bit (8 mm for wall mounting or 3 mm for ceiling tile mounting) • Cat5/6 UTP cable for indoor installations • Shielded Category 5 (or above) cabling should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE.
Hardware Overview LED LED Color Status White Factory default, waiting to be integrated. Flashing White Initializing. Alternating White/Blue Device is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking place. Blue Indicates the device has been successfully integrated into a network and is working properly. This is used to locate an AP. Quickly Flashing Blue When you click Locate in the UniFi Controller software, the AP will flash.
Ports 2 3 Ethernet The Ethernet port is a Gigabit Ethernet port used to connect the power and should be connected to the LAN and DHCP server. Reset The Reset button serves two functions for the UniFi AP: • Restart Press and release the Reset button quickly. • Restore to Factory Default Settings Press and hold the Reset button for more than five seconds. Hardware Installation Wall Mount 1. If the Ethernet cable is coming from the inside of a wall: a.
Connecting Ethernet Connect the Ethernet cable to the Ethernet Port in the base of the FlexHD. Powering the UAP-FlexHD The UAP-FlexHD features auto-sensing 802.3af PoE support and can be powered by any of the following: • Ubiquiti Networks UniFi Switch with 802.3af PoE support • 802.3af PoE compliant switch • Ubiquiti Networks Gigabit PoE Adapter (48V, 0.
Connecting to a PoE+ Switch Connect the Ethernet cable from the UAP-FlexHD directly to an 802.3af PoE port on the switch. Connecting to a PoE Adapter 1. Connect the Ethernet cable from the UAP-FlexHD to the POE port of the Gigabit PoE adapter. 2. Connect an Ethernet cable from your LAN to the LAN port of the Gigabit PoE adapter. 3. Connect the Power Cord to the adapter, and then plug the Power Cord into a power outlet.
Mounting the PoE Adapter (Optional) 1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2. Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included). 3. Align the adapter’s slots with the tabs of the PoE Mounting Bracket, and then slide the adapter down.
Software Installation Download and install the latest version of the UniFi Controller software. Launch it and follow the on-screen instructions. The software and step-by-step instructions in the User Guide are available at: ui.com/download/unifi After you have installed the software and run the UniFi Installation Wizard, a login screen will appear for the UniFi Controller management interface. Enter the Admin Name and Password that you created and click Log In.
Specifications UAP-FlexHD Dimensions Weight Networking Interface Button Power Method Power Supply Max. Power Consumption Operating Frequency Max. TX Power 2.4 GHz 5 GHz Throughput 2.4 GHz 5 GHz Antenna Gain 2.4 GHz 5 GHz Wi-Fi Standards Wireless Security Mounting Ø 48.50 x 159.49 mm (1.90 x 6.28") 315 g (0.69 lb) (1) 10/100/1000 Ethernet Port Reset 802.3af 802.3af 48V, 0.5A Gigabit PoE Adapter 10.5W 2.4 GHz 5 GHz 23 dBm 26 dBm 300 Mbps 1733 Mbps 1.6 dBi 4 dBi 802.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty www.ui.com/support/warranty/ The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
ISED Canada CAN ICES-3(A)/NMB-3(A) This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. 2. This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter (IC: 6545A-UAPFLEXHD) has been approved by ISED Canada.
Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Brazil Nota: Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че този тип радиосъоръжение UAP-FlexHD е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ui.com/compliance Hrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa UAP-FlexHD u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: www.ui.
Malti [Maltese] B’dan, UBIQUITI NETWORKS, niddikjara li dan it-tip ta’ tagħmir tar-radju UAP-FlexHD huwa konformi mad-Direttiva 2014/53/UE. Id-dikjarazzjoni tal-konformità tista’ tiġi kkonsultata minn www.ui.com/compliance Norsk [Norwegian] UBIQUITI NETWORKS erklærer herved at utstyret UAP-FlexHD er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EU-samsvarserklæringen er tilgjengelig på følgende internettadresse: www.ui.
Online Resources Support help.ui.com Community community.ui.com Downloads downloads.ui.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA www.ui.com ©2019 Ubiquiti Inc. All rights reserved. Ubiquiti, the Ubiquiti U logo, the Ubiquiti beam logo, TOUGHCable, and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries.