Outdoor 4-Port PoE Passthrough Switch Model: N-SW
Introduction Thank you for purchasing the Ubiquiti Networks® NanoSwitch™. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents Outdoor 4-Port PoE Passthrough Switch Model: N-SW NanoSwitch Self-Tapping Screw Metal Straps (Qty. 2) Quick Start Guide Installation Requirements Mounting accessories and drain wire are not included. Pole-Mounting • Drill with a 4.
• Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the N-SW and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground.
Hardware Overview System LED LED Port Cover The LED will light blue when the device is powered on.
PoE Link PoE In PoE Out Ground Bonding Point with a Machine Screw and Nut RJ45 LEDs LED PoE Link State Green Green Status Active 24V PoE Link Established Flashing Indicates Activity Ports Port PoE In Description RJ45 port supports 10/100/1000 Ethernet connections and supports 24V, 2-pair passive PoE to power the switch. For maximum power consumption of 30W, we recommend supplying power with the POE‑24-30W-G-WH PoE adapter (not included).
Ground Bonding Point The NanoSwitch must be grounded in one of the following ways: • Use the Self-Tapping Screw to ground the NanoSwitch directly to a grounded metal pole or structure. • Use the Machine Screw and Nut to attach a drain wire (not included) that is connected to a remote grounding block or structure. Connect a Drain Wire (Optional) If a drain wire is used to ground the NanoSwitch, attach it to the Ground Bonding Point with the Self-Tapping Screw and nut.
Hardware Installation Install the NanoSwitch either on a pole or a wall. Follow the appropriate steps for your installation: Pole-Mounting 1. Feed the included Metal Straps through the slots located on the back of the NanoSwitch. 2. Wrap the Metal Straps around the pole. Use a 7 mm socket wrench or screwdriver to turn the screws clockwise and securely fasten the straps to the pole.
3. Remove the Port Cover by pressing on its center and sliding it down. Note: If you are using a drain wire for grounding, proceed to the Connecting Power section. 4. Remove the Self-Tapping Screw and nut from the Ground Bonding Point, and drill a 4.5 mm pilot hole into the pole. 4.
5. Insert the Self-Tapping Screw into the pilot hole. Securely fasten the screw to ensure the Ground Bonding Point is bonded to the pole. Wall-Mounting 1. Secure two screws (not included) to the wall, spaced 38 mm apart. 38 mm 2. Leave a gap of 3 mm from each screw head to the wall.
3. With the drain wire already attached, insert the screw heads into the Keyhole Slots on the back of the NanoSwitch. Press down on the NanoSwitch to secure it.
Connecting Power The NanoSwitch is powered by PoE. Connect an Ethernet cable from a passive 24V, 2-pair PoE power source to the PoE In port. PoE LINK Connecting Ethernet WARNING: PoE is always active. Before connecting a device to a PoE Out port, ensure that the device supports passive PoE and the supplied voltage. 1. Connect an Ethernet cable to a PoE Out port. PoE LINK 2. Connect the other end of the Ethernet cable to a passive 24V, 2-pair PoE device.
Specifications N-SW Dimensions (Excluding Mount) Weight Enclosure Characteristics Total Non-Blocking Line Rate Typical Power Consumption Max. Power Consumption Power Method 196.4 x 93.5 x 32.4 mm ( 7.73 x 3.68 x 1.28") 271 g (9.6 oz) White Polycarbonate 4 Gbps 1.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Australia and New Zealand Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство N-SW е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.
Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo N-SW, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.com/compliance Latviešu valoda [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka N-SW ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES.
www.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2017-2019 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, NanoSwitch, and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries.