User Manual

ManualsBrandsUbee Interactive ManualsElectronicsWireless eMTA

Ubee Interactive — www.ubeeinteractive.com

1 Ubee DVW328 – Safety and Installation Product Insert v1.0

DVW328 Advanced Wireless Voice

Gateway - Safety and Installation

Product Insert

Federal Communications Commission

(FCC) Interference Statement

This device has been tested and found to comply

with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This device generates,

uses, and can radiate radio frequency energy. If

not installed and used in accordance with the

instructions, the device may cause harmful

interference to radio communications. There is

no guarantee, however, that interference will not

occur in a particular installation. If the DEVICE

causes harmful interference to radio or television

reception, which can be determined by turning it

off and on, the user can try to correct the

interference by one of the following measures:

• Increase the separation between the DEVICE

and the equipment with which it is interfering

(for example, a television or radio).

• Connect the DEVICE into an electrical outlet

on a different circuit than the interfered device

is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

FCC Regulatory Information

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired operation.

There is one statement for this product:

• Only the type of PIFA antenna tested may be

used.

Summary of content (7 pages)

PAGE 1
Ubee Interactive — www.ubeeinteractive.com DVW328 Advanced Wireless Voice Gateway - Safety and Installation Product Insert Federal Communications Commission (FCC) Interference Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy.
PAGE 2
Ubee Interactive — www.ubeeinteractive.com FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. IEEE 802.11b or 802.11g operation of this device in the U.S.A. is firmware-limited to channels 1 through 11. For operation within 5.15 ~ 5.35GHz / 5.47 ~5.725GHz frequency range, it is restricted to indoor environment.
PAGE 3
Ubee Interactive — www.ubeeinteractive.com 7. Installation of the device should include grounding the coaxial cable to the earth at the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). The device is designed for IT power systems with phase-to-phase voltage at 120V. 8.
PAGE 4
Ubee Interactive — www.ubeeinteractive.com 3. Connect one end of an RJ11 phone cable to one of the TEL ports on the modem (that has been provisioned for voice service as specified by the service provider), and connect the other end to the phone port of the telephone. Note: If voice service is not provisioned through the service provider, telephone service is not available. 4. Connect the power cord to the POWER port on the device. Plug the other end of the power cord into the AC wall outlet.
PAGE 5
Ubee Interactive — www.ubeeinteractive.com Wall-Mount Installation 148mm (5.75 inches) You can mount the device on a wall using the 2 mounting brackets on the bottom of the device. We recommend that you use two round or pan head screws. 1. Install two screws horizontally apart on a wall using the measurement shown to the right. The screws should protrude from the wall so that you can fit the device between the head of the screw and the wall.
PAGE 6
Ubee Interactive — www.ubeeinteractive.com Additional Information LED Indicators (Color = Blue When On): 1. RESET Button (back of device): This button resets the device to factory defaults. Using a pointed object, insert it into the button opening, and hold for more than 10 seconds. The device will reset and reboot. Note: Not all parameters are reset to factory defaults. Refer to the User Guide for more information. 2.
PAGE 7
Ubee Interactive — www.ubeeinteractive.com 2.4G—When 2.4G Wi-Fi is enabled, the LED is On. When 2.4G Wi-Fi is disabled, the LED is Off. 5G—When 5G Wi-Fi is enabled, the LED is On. When 5G Wi-Fi is disabled, the LED is Off. TEL1 and TEL2—The LED is On when a telephone is on-hook. The LED flashes when a telephone is off-hook. BATTERY—The LED is On when the battery is installed and is charged. The LED is Off if no battery is installed. WPS (top of device)—If not used, the LED is Off.