User's Manual

ManualsBrandsUbee Interactive ManualsElectronicsWireless eMTA

Ubee Interactive — www.ubeeinteractive.com

1 Ubee DVW32G6 – Safety and Installation Product Insert v1.0

DVW32G6 Advanced Wireless Voice

Gateway - Safety and Installation

Product Insert

Federal Communications Commission

(FCC) Interference Statement

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses and can radiate radio frequency energy and,

if not installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one of the

following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

FCC Regulatory Information

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired operation.

There is one statement for this product:

• Only the type of PCB antenna tested may be

Summary of content (8 pages)

PAGE 1
Ubee Interactive — www.ubeeinteractive.com following measures: DVW32G6 Advanced Wireless Voice Gateway - Safety and Installation Product Insert • Reorient or relocate the receiving antenna • Increase the separation equipment and receiver. Federal Communications Commission (FCC) Interference Statement • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
PAGE 2
Ubee Interactive — www.ubeeinteractive.com used. Devices will not permit operations on channels 120-132 for 11a and 11n/a which overlap the 5600 - 5650 MHz band. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. For product available in the USA/Canada market, only channel 1 ~ 11 can be operated. Selection of other channels is not possible. For operation within 5.15 ~ 5.25GHz / 5.47 ~5.
PAGE 3
Ubee Interactive — www.ubeeinteractive.com 5. Clean the device only with a clean, dry cloth. Do not use liquid or chemical cleaners. 6. Avoid static discharge when touching the device by first touching the coaxial connector of the coaxial cable. 7. Installation of the device should include grounding the coaxial cable to the earth at the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable).
PAGE 4
Ubee Interactive — www.ubeeinteractive.com Installation To install this device, follow the procedures below and refer to the following page for a connection diagram. 1. Connect one end of a coaxial cable (not included) to the CABLE port on the device. Connect the other end to a cable splitter or the cable wall outlet. Be sure not to bend or over tighten the cables as this may strain the connector and cause damage.
PAGE 5
Ubee Interactive — www.ubeeinteractive.com Wall-Mount Installation You can mount the device on a wall using the 2 mounting brackets on the bottom of the device. We recommend that you use two round or pan head screws. 1. Install two screws horizontally apart on a wall using the measurement shown to the right. The screws should protrude from the wall so that you can fit the device between the head of the screw and the wall.
PAGE 6
Ubee Interactive — www.ubeeinteractive.com Additional Information LEDs and Other Device Indicators 1. RESET Button (back of device): This button resets the device to factory defaults. Using a pointed object, insert it into the button opening, and hold for more than 10 seconds. The device will reset and reboot. Note: Not all parameters are reset to factory defaults. Refer to the User Guide for more information.
PAGE 7
Ubee Interactive — www.ubeeinteractive.com ONLINE—When the device is obtaining an IP address and configuration file, the LED flashes. When device obtains these items, the LED is On. 2.4G—When 2.4G Wi-Fi is enabled, the LED is On. When 2.4G Wi-Fi is disabled, the LED is Off. 5G—When 5G Wi-Fi is enabled, the LED is On. When 5G Wi-Fi is disabled, the LED is Off.
PAGE 8
Ubee Interactive — www.ubeeinteractive.com Back Panel Ethernet Indicators (Color = Orange or Green): • When an Ethernet device, such as a computer, is connected to the device, the LED is Orange when connected at 10/100 Mbps speeds. • When an Ethernet device, such as a computer, is connected to the device, the LED is Green when connected at 1000 Mbps speeds (Gigabit Ethernet). • When data is being passed between the device and the connected device, the LED flashes.