Ultraloq Lever Fingerprint and Touchscreen Smart Lock Installation and Programming Guide ( V1.
Important Notes • Ultraloq Lever is designed for single-hole doors, doors without a deadbolt. • Do not use a power drill for installation. • Install and test the lock with the door open to avoid being locked out. • Please read all the instructions before contacting customer support. • Please contact customer support before returning the product to the store.
Included in the box Exterior Assembly Interior Mounting Plate Interior Assembly Screwdriver ENGLISH Strike Latch Screw A Screw C Reset Needle Backup Keys AA Batteries User Guide Drilling Template Screw B Fold Drill Template(V1.5) Face of the door Edge of the door Ultraloq Lever Fingerprint and Touchscreen Smart Lock Installation and Programming Guide ( V1.
Installation Guide Installation Video Please watch our easy step by step installation video before attempting to install your Ultraloq Lever Fingerprint and Touchscreen Smart Lock. Or you can also view the website directly. www.u-tec.com/lock/lever/guide 1. Preparing the Door Check the door’s dimensions. Step 1 Measure to confirm that the door is between 15/16”~ 2 ” (33 mm-50 mm) thick. Step 2 Measure to confirm that the diameter of the hole is 2 1/8” (53 mm).
If you are installing your Ultraloq on a door with an existing lock, please remove the current strike and latch. ENGLISH Installing Latch and Strike 1. Install the latch on the door. Make sure the latch angle faces the door jamb. 2. Install the strike on the door frame, ensuring the latch will match the strike.
Installing the Exterior Assembly 1. Place the exterior assembly, facing the right direction. 2. The handle should point away from the door's edge. You can change its direction by rotating it. 3. Make sure the triangle is facing upwards as illustrated. 4. Align the spindle with the slot in the latch and slide it into place. 5. Route the cable through the hole above the latch. You can change the direction of the handle by rotating it.
Installing the Interior Mounting Plate 1. Route the cable through the rectangular hole. The spindle goes through the circular hole. 2. Install the interior mounting plate, make sure the Screw Holes are in the upper part. 3. Secure it to the exterior assembly using screws B.
Installing the Interior Assembly 1. Orient the handle the same way as the outside handle, pointing away from the door's edge. 2. Attach the cable to the connector on the interior assembly, line up the notches on the cable to the slots on the interior assembly. Press the connector firmly until it is completely seated. 3. Align the spindle and insert it into the hole of the interior assembly. 4. Secure the interior assembly using screws C.
Installing the Batteries 1. Insert 3 AA alkaline batteries. 2. Install the battery cover. - + - - - + Testing the Lock Note: Please test the lock with the door open to avoid being locked out. Any fingerprint or code can unlock Ultraloq Lever in factory default mode. 1. Input any code or fingerprint, the LED light of the Ultraloq Lever should turn green. 2. Turn the handle down, the latch should retract smoothly, if it doesn't please follow the instructions carrefully and repeat the installation.
Operation Video www.u-tec.com/lock/lever/guide Please watch our programming and user guide video before attempting to use your Ultraloq Lever Fingerprint and Touchscreen Smart Lock.
1. Lock Parts 1.1 Exterior LED Indicator Fingerprint Reader Micro USB Restart Button Backup Key Hole LED Indicator Shows you authorized or denied access, and battery status. Touchscreen Used to enter the code and unlock from outside. Fingerprint Reader Used to press the finger and unlock from outside. Backup Key Hole Used to insert the key to unlock from outside. Restart Button Used to restart the process if the lock activation fails.
2. Lock Setup Scan the QR Code to download the U-tec App Step 1 Scan the above QR code to download the App, or search “U-tec”in App Store (iOS) and Google Play (Android). Step 2 Open the App, register your U-tec account and log in the account. Step 3 Make sure the lock is in Factory Default Mode. Turn on the Bluetooth on your smartphone, stay near the lock (within 10 feet / 3 meters) and search the lock in the App. Step 4 Pair the lock in the App and start using it.
3. Using Your Lock 3.1 Open the door from outside ① User PIN code Step 1. Touch the lock with the back of your hand to activate the lock , the LED will turn green if the code is correct. Step 3. Turn down the handle to open the door. ② Fingerprint Step 1. Place your finger on the Fingerprint Reader to unlock, the LED will turn green if the fingerprint is correct. Step 2. Turn down the handle to open the door. - 12 - ENGLISH Step 2.
③ Smartphone Use your smartphone to unlock. Please refer to the guide in the U-tec App. Lever 3.2 Open the door from inside Turn down the handle to open the door. 3.3 Lock from outside Close the door and the latch will automatically lock. You can enable the Auto Lock time feature in the U-tec App. 3.4 Reset the Lock Note: All data will be erased if you reset Ultraloq Lever to factory default settings. Step 1. Remove the Battery Cover. Step 2.
3.5 Replace the batteries • When you activate the lock and listen to the message “Low battery”, you should replace the batteries. • Use 3 high-quality alkaline AA batteries for replacement. Lithium batteries may have a longer life, but when they begin to fail, they fail quickly. We don’t recommend them because they don’t give you a lot of time to change your batteries before the lock is completely dead. Please don't use any Rechargeable Battery. 3.
3.8 Finger Placement 1. Your finger should cover the reader completely with some pressure, touching the whole reading area. 2. Make sure that your finger and the fingerprint reader are clean and dry, please note that wet, oily, injured, peeled or dirty fingers may affect the fingerprint identification. 3. To clean the fingerprint reader, use a clean microfiber cloth to wipe off any dirt or debris. 4. While scanning your finger, you shouldn't tap too quickly or move your finger around. 5.
4. Standalone Mode Programming Guide It is recommended to use the U-tec App to program your lock. If you don’t have a smartphone or don’t want to use the App, you may follow the programming instructions below. Standalone Mode is NOT available after the lock is registered in App! Please reset the lock to Factory Default Mode first to program your lock in Standalone Mode. 4.1 Create an Owner Creating the Owner must be the first step prior to any other programming. Only one Owner is available.
4.
Notes ENGLISH
© 2019 U-tec Group Inc. U-tec and Ultraloq brands and products are trademarked and protected under the law in the United States. Unauthorized use is prohibited. Ultraloq is a sub-brand of U-tec Group Inc.
Ultraloq Lever Cerradura Biométrica Inteligente con Lector de Huella Digital y Pantalla Táctil ( V1.
Notas Importantes • Ultraloq Lever está diseñado para usarse en puertas con un solo orificio, puertas sin cerrojo. • No utilices un taladro eléctrico para la instalación. • Instala y prueba la cerradura con la puerta abierta para evitar inconvenientes. • Por favor lee todas las instrucciones antes de contactar a Servicio a Cliente. • Contacta a Servicio a Cliente antes de devolver el producto a la tienda. • No coloques las pilas antes de instalar la cerradura. • Sigue las instrucciones en orden secuencial.
Dentro de la caja Ensamble Exterior Placa de Montaje Interior Ensamble Interior Desarmador ESPAÑOL Contrachapa Pestillo Tornillos A Tornillos C Clip de Reseteo Llaves de respaldo Baterías AA Guía de Usuario Plantilla de perforación Tornillos B Fold Drill Template(V1.
Guía de Instalación Video de Instalación Por favor mira nuestro video instructivo paso por paso antes de instalar tu Ultraloq Lever con huella digital y pantalla táctil. Tambien puedes ingresar al sitio web directamente www.u-tec.com/lock/lever/guide 1. Preparando la puerta Revisa las dimensiones de la puerta: Paso 1 Mide para confirmar que la puerta tiene un ancho entre 15/16”~ 2 ” (33 mm-50 mm) . Paso 2 Mida para confirmar que el diámetro del agujero donde va colocada la cerradura es de 2 1/8” (53 mm).
Si estás instalando tu Ultraloq Lever en una puerta que ya cuenta con una cerradura, por favor quítala junto con el pestillo y la contrachapa. ESPAÑOL Instalación del Pestillo y Contrachapa 1. Instala el pestillo en la puerta. Ten en cuenta que el ángulo del mismo enfrente al marco de la puerta. 2. Instala la contrachapa en el marco de la puerta, teniendo en cuenta que el pestillo quede centrado.
Instalación del Ensamble Exterior 1. Instala el ensamble exterior, asegurándote que va en la posición correcta. 2. La manija tiene que apuntar hacia afuera del borde de la puerta. Puedes cambiar la dirección de la manija girándola hacia un lado o el otro. 3. Asegúrate de que el triángulo está hacia arriba como en la ilustración. 4. Alinea el eje con la ranura en el pestillo y deslízalo en su lugar. 5.
Instalación de la Placa de Montaje Interior 1. Pasa el cable por el orificio rectangular, el eje pasa por el orificio circular. 2. Instala la Placa de Montaje Interior. Aseguráte que los orificios de los tornillos están en la parte superior. 3. Asegúrala al conjunto exterior utilizando los tornillos B.
Instalación del Ensamble Interior 1. Orienta la manija de la misma manera que la manija exterior, apuntando hacia afuera del borde de la puerta. 2. Conecta el cable al conector en el ensamble interior alineando las muescas del cable a las ranuras en el conjunto interior. Presiona firmemente el conector hasta que esté completamente asentado. 3. Alinea el eje en el orificio del Ensamble Interior. 4. Fija el Ensamble Interior con los tornillos C.
Instalación de las baterías 1. Coloca tres baterías alcalinas AA. 2. Instala la tapa. - + - - - + Prueba de la cerradura Nota: Prueba la cerradura con la puerta abierta para evitar cualquier problema. Cualquier huella digital o código puede desbloquear Ultraloq Lever en modo predeterminado de fábrica. 1. Ingresa cualquier código o huella digital, la luz LED del Ultraloq Lever debe ponerse verde. 2. Gira la manija hacia abajo, el pestillo debe retraerse suavemente y podrás abrir la puerta.
Video de Operación www.u-tec.com/lock/lever/guide Por favor escanea el Código QR para ver nuestro video de operación antes de usar tu Ultraloq Lever con Huella Digital y Pantalla Táctil en Modo Independiente.
1. Partes de la cerradura 1.1 Exterior Indicador LED Lector de Huella Digital Micro USB Reiniciar la operación Orificio para llave de respaldo Indicador LED Te muestra accesos autorizados o denegados y el estado de la batería. Pantalla táctil Usada para ingresar el código y desbloquear la cerradura desde afuera. Lector de huella Usado para leer la huella digital y desbloquear la cerradura desde afuera. Llave de respaldo En este lugar deberás ingresar la llave de emergencia en caso de ser necesaria.
2. Configuración de la Cerradura Escanea el código QR para descargar la App de U-tec Paso 1 Escanea el código QR para descargar la App, o busca "U-tec" en App Store (iOS) y Google Play Paso 2 Abre la App, registra tu cuenta de U-tec e ingresa con ella. Paso 3 Asegúrate de que la cerradura está en modo predeterminado de fábrica. Enciende el Bluetooth en tu celular inteligente, quédate cerca de la cerradura (dentro de 10 pies/3 metros) y busca la cerradura en la App.
3. Funcionamiento de la Cerradura 3.1 Abrir la puerta desde afuera ① Código de Usuario Paso 1. Toca la cerradura con el reverso de la mano o con los dedos para activarla. verde si el código es correcto. Paso 3. Rota la manija para abrir la puerta. ② Huella Digital Paso 1. Presiona el dedo en el lector para activar y desbloquear la cerradura, la luz LED se prenderá verde si la huella es correcta. Paso 2. Rota la manija hacia abajo para abrir la puerta. - 12 - ESPAÑOL Paso 2.
③ Celular Inteligente Usa tu celular inteligente para desbloquear. Por favor ve a la guía de uso en la App de U-tec. Lever 3.2 Abrir la puerta desde afuera Rota la manija hacia abajo para abrir la puerta. 3.3 Cerrar desde afuera Cierra la puerta y el pestillo se bloqueará automaticamente. Puedes habilitar el tiempo de Auto Bloqueo desde la App de U-tec. 3.4 Resetear la cerradura Nota: todos los datos se borrarán si restableces el Ultraloq Lever a la configuración predeterminada de fábrica. Paso 1.
3.5 Reemplazo de Baterías · Cuando actives la cerradura y escuches el mensaje "Batería baja", deberás reemplazar las baterías. · Usa 3 baterías alcalinas AA de alta calidad para el reemplazo. Las baterías de litio pueden tener una vida útil más larga, pero cuando comienzan a quedarse sin batería, se agotan rápido. U-tec no las recomienda, ya que no tendrás tiempo suficiente para cambiarlas antes de que no puedas activar la cerradura. Por favor no uses baterías recargables. 3.
3.8 Posición del dedo 1. Tu dedo debe cubrir el lector completamente con algo de presión, tocando toda la zona lectura. 2. Asegúrate de que tu dedo y el lector de huellas estén limpios y secos, ten en cuenta que los dedos mojados, grasosos, pelados o sucios pueden afectar la identificación de las huellas digitales. 3. Para limpiar el lector de huellas digitales, usa un paño de microfibra limpio para limpiar la suciedad o los residuos. 4.
4. Guía de Programación de la cerradura en Modo Independiente Se recomienda utilizar la aplicación U-tec para programar tu cerradura. Si no tienes un teléfono inteligente o no deseas utilizar la aplicación, puedes seguir las instrucciones de programación a ESPAÑOL continuación. Importante El Ultraloq Lever deberá estar en Modo Predeterminado de Fábrica para poder programarlo por medio de la pantalla táctil. 4.
4.
Notas "OZ $IBOHFT PS NPEJGJDBUJPOT OPU FYQSFTTMZ BQQSPWFE CZ UIF QBSUZ SFTQPOTJCMF GPS DPNQMJBODF DPVME WPJE UIF VTFS T BVUIPSJUZ UP PQFSBUF UIF FRVJQNFOU 5IJT EFWJDF DPNQMJFT XJUI QBSU PG UIF '$$ 3VMFT 0QFSBUJPO JT TVCKFDU UP UIF GPMMPXJOH UXP DPOEJUJPOT 5IJT EFWJDF NBZ OPU DBVTF IBSNGVM JOUFSGFSFODF BOE 5IJT EFWJDF NVTU BDDFQU BOZ JOUFSGFSFODF SFDFJWFE JODMVEJOH JOUFSGFSFODF UIBU NBZ DBVTF VOEFTJSFE PQFSBUJPO 3' XBSOJOH 5IF EFWJDF IBT CFFO FWB
© 2019 U-tec Group Inc. Las marcas y los productos de U-tec y Ultraloq están registrados y protegidos bajo la ley en los Estados Unidos. Queda estrictamente prohibido todo uso no autorizado. Ultraloq es submarca de U-tec Group Inc.