802.11g/b Wireless LAN USB 2.0 Adapter with Smart Antenna User Manual Rev 0.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This transmitter must not be co-located or operation in conjunction with any other antenna or transmitter.
Important Before using the Product, please carefully read the precautions described below to ensure proper operation. z Do not open the case or modify contents of the product. Seek the help of an authorized professional if some problem occurs with the product. z This product and other wireless devices may cause interference on each other and as result performance of the product may be affected. z Moving the PC during data transfer may damage the data being transferred.
Table of Contents 1. Network Implementation Using The product ….......................................................6 2. Before Installation ....................................................................................................6 3. Installing the 11g WLAN USB Adapter ....................................................................7 4. The Client Utility Program .......................................................................................
1. Network Implementation Using The product There are two possible types of wireless network configurations using the product: (1) Infrastructure (wireless network using an Access Point) Using the Client/Server or Master/Slave concept, an Access Point is used to link a wired network with wireless clients. Not only can the wireless clients access the wired network but they can also access each other via the Access Point.
- Your SSID (group name of the wireless network) - If you are using a fixed IP address: IP address, gateway address, and subnet mask info. To use the Dual-band Wireless LAN USB Adapter, the device must be equipped with an internal or external USB slot. You should have the latest drivers and utility software for the product (please visit our website for the latest drivers and utility software). 3.
3.4. Click on [Next] and the utility program will be automatically installed as shown in the following screen. 3.5. The following screen will appear when installation is completed. Click on [Finish] to successfully exit the installation process.
4. The Client Utility Program The following are explanations on how to configure and use the Client Utility program. How to Use the Utility Program After completing the above installation and configuration procedures, a new icon as shown below will automatically appear in the lower right tray bar. Double-clicking on the icon will display the following [Client Utility] window.
Each of the pages (Network, Profile, Search, Option, Version) presented in the Client Utility is explained in the following sections. [Network] This page shows how the network is presently configured: network mode, information on the connected AP, TCP/IP, etc. This information cannot be modified in the Network screen.
The “Current Status” window shows the signal quality, signal strength, channel, etc. between the client and AP. It is always in view regardless of which page (Network, Profile, Search, Option, Version) is selected within the Client Utility. [Profile] This page is used to manage connection with Access Points. You can create different configuration profiles for connections with different APs and SSIDs.
2) Select [Express Setup] and click on [Next]. The following screen will appear. Type in the new profile name for the new wireless connection. 3) Click on [Next] and the following screen will appear.
Select a “Network Mode” (Infrastructure or Ad-Hoc) and “SSID”. You do not need to change the default settings of "Power Save Mode" and "Roaming Optimization" unless there is a special need to do so. Refer below for further explanation of each mode. Reference Network Mode Infrastructure: You will need an 802.11b Access Point to use the device in Infrastructure mode. Because all communication will be done via the Access Point, the Access Point’s SSID must be used.
If you do not know the SSID of the devices you want to connect with or want to know the SSIDs of any wireless LAN devices operating in the vicinity, click on [Browse] and the following [Site Survey] screen will appear. Click on [Refresh] to update the list of available SSIDs in the vicinity. [Refresh] will scan the vicinity of a certain amount of time and display the scan results.
4. Click on [Next] and the following screen will appear. Click on [Apply this profile now] to immediately make this profile effective as the current profile and connect to the selected SSID. If you choose to only save the new profile without making it the current profile, do not select this option. 5. Click on [Save] and you will be taken back to the [Profile] page and the new profile automatically added to the “Profile List”.
Remove To remove a profile from the “Profile List” select it and then click on [Remove]. Apply If you want to change the current profile with another profile from the “Profile List”, select the desired profile and click on [Apply]. The new profile will immediately become the current profile and you will be connected with its SSID. Property Selecting a profile from the “Profile List” and clicking on [Property] will allow you to check and/or modify the properties of the selected profile.
Wireless Network: In this page, you can configure parameters such as Network Mode, SSID, and others. WEP (Wired Equivalent Privacy): In this page, you can modify features of the WEP encryption system such as WEP Key, 64 or 128-bit encryption, etc.
When using WEP encryption (available in 64 or 128-bit), only those APs and PCs using the same WEP Key are allowed to communicate with each other. There are three ways of generating a WEP Key: - Make key using PassPhrase: a WEP Key is automatically generated as you type in any PassPhrase of your choice. - Manual Input (ASCII): You generate your own WEP Key using ASCII characters (5 characters for 64-bit and 13 characters for 128-bit).
Advanced: In this page, advanced hardware properties can be modified. Unless you are an advanced user and have deep knowledge about each property in this page, it is recommended that you leave them at the default settings. TCP/IP: In this page, you can modify the network's TCP/IP settings of your PC.
If you want to modify the TCP/IP, select the parameter "Use IP Changer" and the screen below will appear.
Select "Use DHCP" if a dynamic IP is automatically assigned to you each time you connect to the network. Select "Use Static IP below" and type in the TCP/IP information if you are assigned a fixed IP address. Configuring the TCP/IP settings in this page will have the same effect as modifying the TCP/IP settings with Windows' Control Panel except the changes will immediately become effective without rebooting the PC. Consult your network manager to obtain the correct TCP/IP information.
Selecting a network from the [Available Networks] list will enable the [Detail Info], [Connect] and [Add to profile] buttons. [Detail info] will display the following screen showing the selected device's configuration information. An alternative to clicking on [Detail info] is double-clicking on the SSID of choice. [Connect] will immediately connect you with the selected network.
[Add to profile] will have the same effect as clicking on [Add] in the [Profile] page (steps 4.8~4.12). [Option] In this page you can configure various parameters as shown below: [Launch at windows startup] : Selecting this option will automatically start the Client Utility program whenever you start Windows. [Language] : You have the option to select the interface's language between English and Korean. After finishing your parameter settings, click on the [Apply Now] button to immediately apply them.
[Version] Software and Hardware information of the current client device being used by your PC are displayed in this page.
