Bluetooth Conference Bridge BCB-210X User Guide V0.
Table Contents INTRODUCTION .................................................................................................................................... 4 GETTING TO KNOW THE CONFERENCE PHONE KIT .................................................................................. 4 PACKING CONTENTS ..................................................................................................................... 4 IDENTIFYING COMPONENTS ...............................................................
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Introduction Welcome to the Bluetooth Conference Bridge manual. In this manual, you will learn how to use this Conference Phone Kit to do all popular Skype standard functions, such as Conference call, Contacts, History, SkypeOut, SkypeIn, etc. This Conference Phone kit enables you to make and receive Skype calls anywhere, without being in front of the PC.
Antenna MIC3 LED MIC2 LED MIC 3 MIC 2 Speakerphone LCD: 128 x 80 Bluetooth LED Power LED MIC1 LED miniUSB Connector MIC1 Mute LED Sync Skype Contacts Menu Select Concall Participants Make a call, Answer a call, Redial last call, Hold a call Enter / OK End a call, Back to Home Navigation Key Volume (+/-) Clear Input / Last Move to right Enter / OK / Next Power ON/OFF Mute / UnMute 5
Getting Started Minimum System Requirements PC running Windows XP, 2000 Skype software installed At least 600 MHz processor At least 128 MB RAM At least 50MB free disk space on your hard drive CD-ROM drive Setting up the Conference Phone kit 1.
5. Please click Install. 6. Please click Finish. 8. Please select Language from the drop down menu and then click OK. 7. Please click Yes to begin Bluetooth adapter installation. 10. Please select I accept the terms in the license agreement. Click Next 9. Please Click Next 11. Please Click Next 12. Please Click Next 14. Disregard all popup Windows except for the installation Window shown to the right and click Finish 13. Click Install Win2K only 16.
18. Power On The Bluetooth Phone and press the Menu ) located button ( below the LCD screen. Select Pairing from the menu and then press the Call button to enter Pairing Mode. Click OK 17. Click Search. Note: If a window popup to ask you enter PIN code, please enter “0000” 19. Select your Bluetooth Phone (Please check the MAC address to select the right device. Please remove the battery to locate the MAC address label). Click OK. 20. To finishing Bluetooth pairing click OK. 21.
Exploring the Conference Kit Display Display Icons Volume Operation Battery Status Skype Status Signal Strength Icons Operation Description Indicate which operation your phone is doing.
Main page Press to go to main page. 4 possible cases on main page: 1. Bluetooth is disconnected: LCD shows “BT Phone”, Signal strength icon is disconnected 2. Bluetooth is connected but skype is not signed in: LCD shows “BT Phone / Skype Unavailable”, Signal strength icon shows levels of signal strength 3. Bluetooth is connected and skype is signed in: LCD shows “BT Phone” 4. Bluetooth is connected, skype is signed in and has missed calls: LCD shows “BT Phone / # Missed calls”.
Configuration Menu Press to enter configuration menu Missed Calls Incoming Calls History Outgoing Calls Skype Me Online Status Away Not Available Do Not Disturb Invisible Menu Offline Operation Mode Headset Mode Standby Mode Normal Mode Pairing Pairing … Skype Credit Other Settings Key Tone OFF Key Tone ON Reset To Default Firmware Version Language Submenus Missed Calls Descriptions Display Missed call lists History Incoming Calls Display Incoming call lists Outgoing Calls Display Outgoin
Reset To Default F/W Version Showing F/W version installed. 1st MAC address: MAC address of this device 2nd MAC address: MAC address of Paired USB Adapter Languages Select LCD display language Guide to Basic Functions Call Skype™ Contact 1. Press to turn on device Wait until phone shows “ClearSky” and signal strength icon shows “connected” press to sync contact lists with PC skype to scroll up/down the contact lists 2. Use List button 3. Press to start a call. 4.
4. Choose “P2P CALL” to hold 1st call and talk to 2nd contact. B. invite contacts and conference them together 1. Press to go to the contact list menu. to mark the contact you want to include in this conference call. (Conference participants 2. Press (max 4+host) 3. Press to start this conference call Redial outgoing calls 1. Press to show outgoing call lists. 2. Select the contact (from the outgoing call list) you want to dial to make a call. 3.
Appendix Specifications RF Standard Class 1 Bluetooth v2.0 with EDR Backward compatible with Bluetooth v1.1 & v1.2 RF Frequency 2.4~2.4835 GHz, ISM band Spread Spectrum Frequency Hopping and Adaptive Frequency Hopping RF Output Power Up to 17 dBm (maximum) Display 128 x 80 pixel, graphical type STN LCD with backlight Mini-USB connector for charging from computer USB port or external power adapter Interface Built-in Mono-Speaker / Microphone 1.
Off-hook, Make a call, Answer a call Redial last calls Mute Microphone Power on / off Dimension 242 x 242 x 54 mm (9.5 x 9.5 x 2.1 in.) Environmental Operating Temperature: 0 ~50° C , Humidity:10 ~ 90% Condition Storage Temperature: -20 ~70° C, Humidity:10 ~ 90% Certifications FCC, CE Note: According to Bluetooth spec, the signal range of Class 1 is 100 meters. 100 meters is the maximum distance that is realistically possible.
Troubleshooting Problem: Press “Power on” button, but nothing happen, no display Solution: 1. Make sure the included rechargeable battery is fitted in the handset correctly. Problem: Pop up a Bluetooth Security window Solution: 1. Bluetooth PIN should be self-assigned when pairing with Bluetooth phone. If this window pop up, please input default Bluetooth PIN: “0000”.
