Specifications

ManualsBrandsU-Line ManualsNail GunH-3071

PAGE 1 OF 9 0512 IH-3071

H-3071

NAIL GUN

1-800-295-5510

uline.com

INSTRUCTIONS

SAFETY INSTRUCTIONS

WARNING! EYE PROTECTION which conforms to

ANSI specifications and provides protection

against flying particles both from the FRONT

and SIDE should ALWAYS be worn by the

operator and others in the work area when

connecting to air supply, loading, operating

or servicing this tool. Eye protection is required

to guard against flying fasteners and debris

which could cause severe eye injury.

The employer and/or user must ensure that

proper eye protection is worn. Eye protection

equipment must conform to the requirements

of the American National Standards Institute,

ANSI Z87.1, and provide both frontal and side

protection.

NOTE: Non-side shielded spectacles and

face shields alone do not provide adequate

protection.

CAUTION: Additional safety protection will be

required in some environments. For example,

the working area may include exposure to

noise level which can lead to hearing damage.

The employer and user must ensure that any

necessary hearing protection is provided and

used by the operator and others in the work

area. Some environments will require the use

of head protection equipment. When required,

the employer and user must ensure that head

protection conforming to ANSI Z89.1 is used.

AIR SUPPLY AND CONNECTIONS

WARNING! Do not use oxygen, combustible

gases or bottled gases as a power source for

this tool, as tool may explode, possibly causing

injury.

WARNING! Do not use supply sources which

can potentially exceed 200 psig as tool may

burst, possibly causing injury.

WARNING! The connector on the tool must not

hold pressure when air supply is disconnected.

If a wrong fitting is used, the tool can remain

charged with air after disconnecting and thus

will be able to drive a fastener even after the

air line is disconnected, possibly causing injury.

WARNING! Do not pull trigger or depress

contact arm while connected to the air supply

as the tool may cycle, possibly causing injury.

WARNING! Always disconnect air supply:

1) Before making adjustments; 2) When

servicing the tool; 3) When clearing a jam;

4) When tool is not in use; 5) When moving to

a different work area, as accidental actuation

may occur, possibly causing injury.

LOADING TOOL

WARNING! When loading tool: 1) Never place a

hand or any part of body in fastener discharge

area of tool; 2) Never point tool at anyone;

3) Do not pull the trigger or depress the trip

as accidental actuation may occur, possibly

causing injury.

BOSTITCH

Summary of content (9 pages)

PAGE 1
π H-3071 NAIL GUN 1-800-295-5510 uline.com BOSTITCH INSTRUCTIONS SAFETY INSTRUCTIONS WARNING! EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris which could cause severe eye injury.
PAGE 2
INSTRUCTIONS CONTINUED OPERATION WARNING! Always handle the tool with care: 1) Never engage in horseplay; 2) Never pull the trigger unless nose is directed toward the work; 3) Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur, possibly causing injury.
PAGE 3
INSTRUCTIONS CONTINUED MODES OF OPERATION SUPPLY SOURCE BOSTITCH OFFERS TWO MODES OF OPERATION FOR THIS SERIES TOOL. Use only clean regulated compressed air as a power source for this tool. NEVER USE OXYGEN, COMBUSTIBLE GASES OR BOTTLED GASES AS A POWER SOURCE FOR THIS TOOL AS TOOL MAY EXPLODE. SEQUENTIAL TRIP (Gray trigger) The Sequential Trip requires the operator to hold the tool against the work surface before pulling the trigger.
PAGE 4
INSTRUCTIONS CONTINUED LUBRICATION CONTINUED COLD WEATHER OPERATION For cold weather operation near and below freezing, the moisture in the air line may freeze and prevent tool operation. We recommend the use of BOSTITCH winter formula air tool lubricant (included) or permanent antifreeze (ethylene glycol) as a cold weather lubricant.
PAGE 5
INSTRUCTIONS CONTINUED FASTENER DEPTH CONTROL ADJUSTMENT CONTINUED connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. TO ADJUST THE FASTENER DEPTH CONTROL The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.
PAGE 6
INSTRUCTIONS CONTINUED TOOL OPERATION CONTINUED b. The Sequential Trip (gray trigger) allows "place nailing" without the possibility of driving a second, unwanted fastener on recoil as described below under "Contact Trip". 2. CONTACT TRIP (CONVENTIONAL) OPERATION (BLACK TRIGGER) Your new BOSTITCH tool can be configured for use in Contact Trip mode. To drive a nail, the "trip" and the trigger must both be depressed.
PAGE 7
INSTRUCTIONS CONTINUED TOOL OPERATION CHECK CONTINUED MAINTAINING THE PNEUMATIC TOOL WARNING! When working on air tools, note the warnings in this manual and use extra care evaluating problem tools. IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANUAL OBSERVE THE FOLLOWING FOR SAFE OPERATION REPLACEMENT PARTS • Use the BOSTITCH pneumatic tool only for the purpose for which it was designed.
PAGE 8
Troubleshooting CONTINUED Operating Issue Failure to cycle Lack of power; slow to cycle Skipping fasteners; intermittent feed Fasteners jam in tool PAGE 8 OF 9 CAUSE CORRECTION Air supply restriction Check air supply equipment Tool dry, lack of lubrication Use BOSTITCH Air Tool Lubricant Worn head valve O-rings Replace O-rings Broken cylinder cap spring Replace cylinder cap spring Tool dry, lacks lubrication Use BOSTITCH Air Tool Lubricant Broken cylinder cap spring Replace cap spring O
PAGE 9
Troubleshooting CONTINUED COIL NAILERS Operating Issue Skipping fasteners; intermittent feed Fasteners jam in tool/canister CAUSE CORRECTION Feed piston dry Add BOSTITCH Air Tool Lubricant in hole in feed piston cover Feed piston O-rings cracked/worn Replace O-rings/check bumper and spring.