Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 1 (27) Godkänd av / Approved by WCS Module User Manual WCS Module User Manual This document contains necessary information to setup and implement this module into different end products.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 2 (27) Godkänd av / Approved by WCS Module User Manual Table of content 1 Scope....................................................................................................................................... 3 1.1 1.2 1.3 2 3 Referenced documents ..........................................................................................................
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 3 (27) Godkänd av / Approved by WCS Module User Manual 1 Scope 1.1 Identification This document contains information to setup and implement this module into different end products. The product identification ID is cB-0720-02. 1.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 4 (27) Godkänd av / Approved by WCS Module User Manual 2 Referenced documents [1] connectBlue Environmental Standard, cBProject-0202-03(1), 2002-02-04, connectBlue AB. [2] Advanced Audio Distribution Profile, Adopted version 1.0, 2003-05-25, Bluetooth SIG. [3] Specification of the Bluetooth System, Profiles, Version 1.1, 2001-02, Bluetooth SIG.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Sida / Page 5 (27) Ärende / Subjekt Godkänd av / Approved by WCS Module User Manual 3 Characteristics 3.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 6 (27) Godkänd av / Approved by WCS Module User Manual and output to control the module. “Red” (LED-GREEN in the pinning list, section 3.4), “Green” (LED-GREEN) and “Mute” (NF-MUTE) are outputs and MF (MULTI-FUNCTION), VOL+ (VOLDOWN), VOL- (VOL-UP) and Talk Indicator (TALK-IND) are inputs (see below for the functionality of these pins).
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 7 (27) Godkänd av / Approved by WCS Module User Manual See Figure 1 for an overview of how the Bluetooth module is interfacing the rest of the Receiver electronics. The user interface consists of three main modes. • Setup (indicated with very fast green blinks on the LED PIO). Later called LED-Setup. • Idle (indicated with slow green blinks on the LED PIO).
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 8 (27) Godkänd av / Approved by WCS Module User Manual Pairing is performed in setup mode only. 3.2.4.1.1 Pairing with a phone Activate the VOL+ input shortly (less than 2 seconds). The receiver goes into pairable mode (indicated by LED-Pair) and the receiver will be discoverable for other units.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 9 (27) Godkänd av / Approved by WCS Module User Manual 3. Intercom state. Intercom between the two receivers is active. Indicated on the LED PIOs by LED-Connect. 4. Phone state. An active phone call is connected. Indicated on the LED PIOs by LED-Connect. 5. AV state. An active Hifi quality sound session is active. Indicated on the LED PIOs by LEDConnect. 6.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 10 (27) Godkänd av / Approved by WCS Module User Manual during the Intercom session) the Intercom session is terminated and the receiver is moved to Idle state. 3. If the previous state was the AV State and the TI been inactive for more than 10 sec the Intercom session is terminated. An AV connection is initiated and faded in.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 11 (27) Godkänd av / Approved by WCS Module User Manual 2. If the unit is in the Idle state a phone call is transferred back from the phone to the receiver by an activation of the MF input. 3.2.8 AV State Functionality The AV state is always initially initiated from the base unit (or other AV device). Initial procedure: 1.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 12 (27) Godkänd av / Approved by WCS Module User Manual Level 2 (below 3.5 V). Two low battery sounds are played and two red flashes on the LED PIOs are displayed periodically (every 60 s). Called IND-Battery2. Level 3 (below 3.4 V). Three low battery sounds are played and three red flashes on the LED PIOs are displayed periodically (every 60 s). Called IND-Battery3.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 13 (27) Godkänd av / Approved by WCS Module User Manual 3. Walkie-talkie state. An intercom session with a receiver is active. Indicated by LED-Connect. Prioritized audio messages (e.g. navigation information from GPS) does not use a separate state. Instead the information is sent via walkie-talkie or AV. 3.3.5 AV State AV state may be entered from the Idle state.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 14 (27) Godkänd av / Approved by WCS Module User Manual If VOL- goes high all pairing information is erased. IND-Success indication is issued when finished. The Idle stat is indicated by LED-Idle. 3.3.7 Pairing State Pairing state may be entered from the Idle state only. 1. Pairing state is entered when VOL+ is moved inactive to active state. 2.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 15 (27) Godkänd av / Approved by WCS Module User Manual 1. The TI and NI are monitored continuously. 2. When both the TI and NI become inactive the intercom session with the first receiver paired with the base unit is terminated. 3. If the previous state was the Idle state or the MF is inactive the base unit is moved to Idle state. 4.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Sida / Page 16 (27) Ärende / Subjekt Godkänd av / Approved by WCS Module User Manual 3.4 Electrical interface requirements 3.4.1 Overview Module Interface CSR BC358239A Radio & Baseband Bluetooth IC Internal Antenna RESET-n SPI UART Digital-I/O J3 Optional External Antenna connector Analog -I/O RF-connect Analog Interface 5 J1 4 9 Power supply Vin (2.2V - 4.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 17 (27) Godkänd av / Approved by WCS Module User Manual 1. AC or DC coupled differential output capable of driving 2Vpp into 600 Ω, maximum load impedance is 22 Ω. DC bias level is 0.8 V The Audio-input signals has the following behavior: 1. Differential line input, input impedance 130 kΩ. Use the left channel for mono input signal is needed only (e.g.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 18 (27) Godkänd av / Approved by WCS Module User Manual 9 SPI-MISO SPI 10 SPI-CLK SPI 11 SPI-MOSI SPI 12 SPI-CSB SPI RESET-N Digital IO 14 Reset. Active low. 3.4.5 Digital IO The module digital interface voltage input levels are logic level CMOS i.e. VIL < 0.3 x VCC VIH > 0.7 x VCC.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 19 (27) Godkänd av / Approved by WCS Module User Manual 13 GND Power Module GND 24 +3V Power Power output from onboard regulator 25 VCC Power Positive supply voltage 26 VCC Power Positive supply voltage 29 GND Power Module GND 30 GND Power Module GND 3.5 Mechanical Requirements 3.5.1 PCB Outlines The size of the unit is 22 by 35 mm.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 20 (27) Godkänd av / Approved by WCS Module User Manual There are two mounting holes available on the board (see Figure 3). 3.5.3 Environmental requirements The environmental requirement follows the connectBlue Environmental Standard [1]. The operating temperature range with guaranteed radio performance is from -25°C to +85°C.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 21 (27) Godkänd av / Approved by WCS Module User Manual 4 Regulatory 4.1 FCC Compliance 4.1.1 FCC Statement This device complies with RF-exposure evaluation for portable devices in FCC rules section 2.1093. This device complies with Part 15 of the FCC Rules.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref. 2005-03-30 cBProject-0503-17 (1) Ärende / Subjekt Sida / Page 22 (27) Godkänd av / Approved by WCS Module User Manual (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref.
Utfärdare / Issued by Mats Andersson Datum / Date Beteckning / Ref.