User's Manual

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsIndoor Ceiling Mount Surveillance Transceiver

BIS-4170 IVS PEOPLE COUNTER 8200-2702-01, REV. 4A

INSTALLATION AND PLANNING GUIDE

1 of 23

BIS-4170

IVS People Counter

Installation and Planning Guide

For Mounting Heights: 2.4–4.3m (8–14ft)

To the Installer

WARNING! Install the people counter IVS device in an air space not used for environmental air. DO

NOT install the IVS device in a plenum or other environmental air-handling space.

For indoor use only.

Cables placed in environmental airspace must be plenum rated unless the cables are in raceways.

Contents

About the People Counter..................................... 2

Mounting Considerations....................................... 5

Installation Procedure............................................ 7

Running the Cables............................................ 8

Mounting the IVS Device ................................... 9

To a Ceiling Tile............................................ 10

To a Ceiling T-Bar......................................... 10

To a Wall....................................................... 11

To Wood or Sheetrock Ceilings.................... 12

Connecting Video, Communications,

and Power to the IVS Device ........................... 13

Verification Test ............................................... 15

Specifications ...................................................... 22

Declarations ........................................................ 22

Appendix A: Site Survey Form .......................... 23

Summary of content (23 pages)

PAGE 1
BIS-4170 IVS People Counter Installation and Planning Guide For Mounting Heights: 2.4–4.3m (8–14ft) To the Installer ! WARNING! Install the people counter IVS device in an air space not used for environmental air. DO NOT install the IVS device in a plenum or other environmental air-handling space. For indoor use only. Cables placed in environmental airspace must be plenum rated unless the cables are in raceways. Contents About the People Counter .....................................
PAGE 2
About the People Counter Mounted at ceiling heights up to 4.3m (14ft), the IVS People Counter device (Figure 1) tracks the paths of people within its field-of-view (Figure 2). The IVS device can cover an entrance up to 2.4m (8ft). The IVS device is also capable of reporting counts to a remote location through one of the following dedicated communication interfaces: • Ethernet • LDM II via RS-485 • Bluetooth. Figure 1. IVS device Figure 2.
PAGE 3
Coverage Ceiling-mounted up to a height of 4.3m (14ft), the IVS device can cover a doorway or opening up to 2.4m (8ft) wide. The IVS device is powered by a 48Vdc Power over the Ethernet (PoE) device. Tracking A floor-facing camera in the IVS device is used to determine the height of a desired target (adults), and thus to distinguish them from undesired targets such as shopping carts, pets, and children. • A count line is projected across the entrance.
PAGE 4
Figure 3. IVS device orientation Hardware Features BIS-4170 IVS PEOPLE COUNTER INSTALLATION AND PLANNING GUIDE 8200-2702-01, REV.
PAGE 5
Mounting Considerations Perform a site survey (Appendix A) while observing the installation site for the following considerations. Ceiling Considerations • Composition: Sheet rock, plaster, suspended ceiling. The IVS device can attach to any 1/4-20 thread-per-inch bolt of a customer mounting bracket. • Height: The IVS device can be mounted up to a height of 4.3m (14ft). CAUTION: The tilt of the IVS device should follow the slope of the floor.
PAGE 6
Traffic Corral Points Check for walls, displays and anti-theft pedestals that help corral traffic. Ideally, the traffic path should be elongated as much as possible under the IVS device. PoE Device The PoE device supplied with the IVS device is typically placed in computer wiring room or next to the IVS device near a convenient power outlet. The PoE comes with a 1.8m (6ft) power cable. Other Considerations • 24-hour or timed power available.
PAGE 7
Installation Procedure Parts Required • DVR for verification testing (The DVR records video data “seen” by the IVS device.) • Cat5 cable • IVS device • ¼-20 threaded rod • ¼-20 nuts (2) Optional Parts* ? BIS-4170 IVS PEOPLE COUNTER INSTALLATION AND PLANNING GUIDE 8200-2702-01, REV.
PAGE 8
Running the Cables Run a Cat5 cable from the installation site for the IVS device to the installation site for the PoE. Run another cable from the PoE to the store’s computer wiring room. Note: Cat5 cable runs cannot exceed 100m (330ft) without using a repeater. Terminate cables following Error! Reference source not found. below. • Use plenum / non-plenum cable per local requirements. • Use pre-manufactured patch cables when available. • Leave a sufficient service loop at end of each home run.
PAGE 9
Mounting the IVS Device The IVS device can be installed at heights up to 4.3m (14ft) using one of the following methods: surface mounting bracket or recessed mounting bracket. ! ! ! WARNING! Install the IVS device in an air space not used for environmental air. DO NOT install in a plenum or other environmental air-handling space. WARNING! The ceiling must support up to 5.1kg (11.2 lbs).
PAGE 10
To a Ceiling Tile 1. Do the following to prepare the tile (Figure ): • Remove the ceiling tile and drill a ¼-inch hole in its center. • Cut a 2.5ft piece of wood 2x4 and drill a ¼-inch hole in its center. • Center the 2x4 above the tile structure. Then place the ¼-20 threaded rod though the hole and secure it from above and below with two ¼-20 nuts. Ensure the rod extends only about ¼-inch below the tile. • Reinsert the ceiling tile with the threaded rod protruding through the hole in the tile. 2.
PAGE 11
3. Attach two mounting brackets to the outside of the top shell with two screws as shown. 4. Maneuver the brackets into place, then tighten the two locking crews from below to secure the top shell to the T-bar. Locking Screws (2) To a Wall The RHIUCM wall mounting bracket enables the IVS device to mount to a wall. Additional Parts Required RHIUCM wall mounting bracket (1) 1. Loosen the two bottom screws in the IVS device and remove its top shell. 2.
PAGE 12
6. Attach the cover to the bracket/counter assembly. To Wood or Sheetrock Ceilings (TBD) BIS-4170 IVS PEOPLE COUNTER INSTALLATION AND PLANNING GUIDE 8200-2702-01, REV.
PAGE 13
Connecting Video, Communications, and Power to the IVS Device The PoE can be placed in the computer room (where power is readily accessible) as long as cable length from the PoE to the IVS Device does not exceed 100m (330ft). The minimum cable length is 0.5m. 1. Connect the following cables (Figure 4): a. Connect a Cat5 cable between the host computer and the LAN input on the PoE. b.
PAGE 14
2. For Video to the DVR, plug the pigtail connector of the DVR video cable to connectors E1 and E2 inside the IVS Device. 3. Attach the bottom shell to the top shell. Tighten both screws securely. 4. Once the PoE injector into a 24-hour outlet, the IVS device will begin its boot up process. This process takes about 40 seconds, where the Power/Status LED on the PoE module momentarily turns yellow (stand by), then green indicating that the PoE has successfully identified the IVS as a PoE compliant device.
PAGE 15
Verification Test 1. Check out the entire ‘IVS Engineering Test Tool Setup’ folder from StarTeam. Locate the ‘IVS Engineering Test Tool’ icon on the desktop of your laptop. The Test Tool is used to perform initial installation of the IVS and can be used to verify count information obtained from the IVS Device. Communications will occur via one of two communications media: Ethernet or Bluetooth (selectable via a pull down menu).
PAGE 16
3. From the pull down menu ‘Select COM’, select ‘Configure’ to invoke the following ‘Input Requested’ dialog box. Enter the IP address for the IVS Device and click OK. 4. Connect a Cat5 cable from the PoE Injector “LAN” port to the Ethernet port on your laptop. 5. From the ‘Select COM’ pull down menu, select ‘TCP/IP’. At the bottom of the screen, click ‘Connect’. 6. Verify that the addressed IVS Device is ‘Connected’ to the IVS Engineering Test Tool.
PAGE 17
7. On the side panel of the Test Tool, select the ‘Image’ tab. Then from the ‘Get’ pull down menu, select ‘Image’. Verify on the DVR screen that the IVS Device is capturing and processing the video image. 8. Verify that the image on your display corresponds to the image “seen” by the IVS device. 9. Select ‘New Line’ from the side panel of the Test Tool. Select the line color from color palette and click OK. 10.
PAGE 18
Adjusting the Count Line Setting the IP Address for the IVS Device The IVS device automatically sets the count line at the middle of its field-of-view. However, in certain situations, the line may have to be moved forward or backward. Auto addressing Each IVS Device is automatically assigned a Static IP address of 198.168.0.1. The best method is to disconnect all network connections from your laptop, manually assign it an IP address (such as 192.168.1.10), and then connect it directly to the IVS Device.
PAGE 19
3. Double-click Network Connections. The Network Connections window appears. Set a Static IP Address on Your Laptop IMPORTANT! Set the static IP address on your computer BEFORE connecting the IVS Device to it. Note: The network cable connection my have a different name in some systems such as “Laptop ethernet port”. IMPORTANT! Disconnect the Ethernet (Cat5) cable from your laptop and disable any wireless connections. No other network connections can be active during this process. 1.
PAGE 20
6. On the Internet Protocol (TCP/IP) box, click OK. Then click the X in the top-right corner to close the window. 5. Select Internet Protocol (TCP/IP) and click Properties. The Internet Protocol (TCP/IP) Properties dialog box appears. IMPORTANT! Write down the current settings in Internet Protocol (TCP/IP) Properties dialog box so that you can re-establish them after you set the network parameters on the IVS Device. • Select Use the following IP address and type an IP address for your computer to use.
PAGE 21
8. To save your changes, click Save. Set the IP Address of the IVS Device Once you have set the IP address on your PC and have connected the IVS Device and PoE injector to your PC, you are ready to set the IP address of the IVS Device. Complete the following steps to set the IP address of the IVS Device: 1. Re-connect your laptop to Wi-Fi. 2. Open a web browser and in the address bar type http://192.168.1.7. Press Enter. The CLARITY Basic Configuration screen appears.
PAGE 22
Specifications Declarations Electrical Regulatory Compliance Primary Input ................................................ 48Vdc, 0.5A Power consumption .......................................... 14W Max Certified Limited Power Source EMC ....................................................... 47 CFR, Part 15 Network FCC COMPLIANCE: This equipment complies with Part 15 of the FCC rules for Class A digital devices when installed and used in accordance with the instruction manual.
PAGE 23
Appendix A: Site Survey Form General Information Customer Name Site Name and Number Site Address Site Telephone Number Hours Of Operation Mon Thu Tue Wed Fri Sat Sun Local Contact Name Contact Telephone Survey Performed By Survey Date and Time Ceiling Information Ceiling Height IVS Device Mounting Height Ceiling Slope Ceiling Composition Ceiling Access Additional Considerations Door Information Door Width Pedestals (yes/no) Door Type Additional Considerations Other Information Floor Slope Head-E