User's Manual

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsUltra Max Phasing Tool

Preliminary

ULTRA MAX PHASING TOOL 8000-2579-49 REV. B

USER GUIDE

1 of 9

8000-2579-49

Ultra Max

Phasing Tool

User Guide

AMX-1000

If you need assistance...

Contact your Technical Support.

About this guide

This guide provides you with information on how to

use the Phasing Tool. This tool eliminates the need

to use an oscilloscope when wirelessly phasing

and synchronizing systems.

About the product

Part numbers

Table 1. AMX-1000 Phasing tool kit with case

Item Qty Part Number

Phasing Tool 2 0304-0152-01

Brackets for Sense Coil 2 0400-1182-01

Sense Coils 2 0300-2274-01

Cable RG58A 12ft 1 6003-0313-01

Cable USB A/Micro B 6ft 1 6003-0148-01

ntenna 2.4GHz 2 3411-0024-01

Spare parts

A complete parts list is available online at:

http://www.sensormatic.com/support/techsupport/.

the Tech Support home page.

Part Number /

Product Code Description

9U*

FRU**

0352-0706-01 3dB Transceiver Antenna No Yes

0352-0707-01 Pickup Coil and Bracket No Yes

0352-0708-01 Phasing Tool Transceiver

Module

No Yes*

* Repairable unit

** Field replaceable unit.

*** Outside North America only.

Key features

Two identical phase modules are used. One is set

as a transmitter and the other is set as a receiver.

Both the receiver and transmitter are battery

operated. When the unit is connected to the laptop

via USB cable it switches to USB power.

The sense coils pick up a 58kHz signal from the

antenna. An application on the laptop shows the

phase delta between the systems. No oscilloscope

is required to complete phasing.

Summary of content (9 pages)

PAGE 1
Preliminary Ultra Max® Phasing Tool About the product User Guide Part numbers Table 1. AMX-1000 Phasing tool kit with case Item Qty Part Number Phasing Tool 2 0304-0152-01 Brackets for Sense Coil 2 0400-1182-01 Sense Coils 2 0300-2274-01 Cable RG58A 12ft 1 6003-0313-01 Cable USB A/Micro B 6ft 1 6003-0148-01 Antenna 2.4GHz 2 3411-0024-01 Spare parts AMX-1000 Contact your Technical Support. About this guide This guide provides you with information on how to use the Phasing Tool.
PAGE 2
Preliminary relationship to the reference system on the level LED’s. The LEDs flash as follows: Front Panel functions LED Number LED #1 System Phase is Lagging by more than 50 µsec LED #2 System Phase is Between plus or minus 50 µsec LED #3 System Phase is Leading by more than 50 µsec Note: 1 millisecond (msec or ms) = 1000 microseconds (µsec or µs). RSSI Signal Strength Reading Press and release SW2 once.
PAGE 3
Preliminary ***|***|***|000:-10: LOCKED: (-77:54:131)!99-5556 Figure 1.Primary Transmitter Setup Coaxial Cable Strength= 3 PLL The “2” command is a toggle. Typing “2” again turns the mode off. Enable Boot Loader Mode Ensure the power switch is off. Press and hold SW1 and SW2 simultaneously while sliding the power switch to the ON position. Continue pressing SW1 and SW2 until all 3 level LEDs are flashing. At this point SW1 and SW2 may be released.
PAGE 4
Preliminary  If LED 2 is lit system being checked is within the +/- 50usec window considered to be in-phase 2. PuTTY is used to talk to the tool and the System Configurator is used to perform the phase adjustment.  If LED 3 is lit system being checked is leading greater than 50usec The phasing tool displays the phase delta and other information on the laptop using PuTTY as the interface. 1. Install the provided USB driver. This is included in the ADS4 bundle available on www.sensormatic.com.
PAGE 5
Preliminary 5. Select Open to open the console window. Below is an example of the PuTTY initialization screen. Figure 6. Example of PuTTY screen Figure 5. PuTTY Configuration 8. To display the phase delta, press enter, and then type 1 in the command line. This shows if the signal from the system being phased is leading or lagging from the reference system. The value is displayed in microseconds and milliseconds for convenience. Note: Refer to the appendix for a list of PuTTY commands. 6.
PAGE 6
Preliminary Phasing Tools Comparison Appendix Figure 10.
PAGE 7
Preliminary Figure 7. M4K Controller Led Status Phasing State LED 1 On Phasing is leading LED 2 On System is In-phased LED 3 On Phasing is lagging Note: If Level LED 2 is On, the system is In-Phased and the procedure is complete. Note: If Level LED 1 or 3 are On, press 1 on PuTTY and continue to make adjustments. Location of potentiometer Phasing tool firmware update procedure 4. Open the PuTTY screen. The Console Menu will display. See Figure 8. Figure 8.
PAGE 8
Preliminary 6. The phasing unit will always reset after a flash download. Figure 11. COM port selection Upgrading the Radio Image (.hex file) 1. Close the configurator application and restart. 2. Start the phasing tool in boot loader mode as outlined above. 3. Select Communications>Local>USB as outlined above. 4. When the connection is made to the target the configurator displays a dialogue box asking for a radio application. Click Cancel. 5. Click the checkbox for Radio App.
PAGE 9
Preliminary La operación de este equipo está sujeta a las siguientes dos condiciones: Approved Antennas Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.