User's Manual

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsANTI-PILFERAGE DEVICE

Table Of Contents

AMS-9050 CONTROLLER 8200-0537-02, REV. B

INSTALLATION AND SERVICE GUIDE

1 of 31

AMS-9050 Controller

Installation and Service Guide

ZE9050

Contents

To the Installer....................................................... 1

About the Product.................................................. 2

Device Connections ........................................... 3

Installation Features........................................... 7

Service Features ................................................ 8

Installation Requirements...................................... 9

Controller Installation........................................... 11

Troubleshooting................................................... 13

Fuse Replacement .............................................. 15

Specifications ...................................................... 15

Declarations ........................................................ 16

To the Installer

This installation and service guide explains how to

install, setup, and service the AMS-9050 controller.

Parts required to install this system are:

- AMS-9050 controller

- AMS-1100/1101 exit antenna(s) or

AMS-1080 aisle antenna(s)

Other documents that may be required for

installation are:

- AMS-9050 Planning Guide, 8200-0537-01.

Note: There may be installation

restrictions on antennas in certain

countries. See antenna installation guides

for restrictions, if any.

Regulatory Restriction: This device is

only intended to be installed as described

in the installation guide.

- Because customer requirements dictate the

placement of system components, your

Sensormatic representative will supply this

information separately.

- If this product was installed in a European

Union or European Free Trade Association

member state, please give the Declaration of

Conformity included with this product to the

manager or user. By law, this information must

be provided to the user.

- Because of the number of antennas and

accessories that can connect to this controller,

methodically install this system to avoid

problems. See “System Setup” in this guide for

guidance on how to setup antennas.

Summary of content (31 pages)

PAGE 1
AMS-9050 Controller To the Installer Installation and Service Guide This installation and service guide explains how to install, setup, and service the AMS-9050 controller. Parts required to install this system are: - AMS-9050 controller - AMS-1100/1101 exit antenna(s) or AMS-1080 aisle antenna(s) Other documents that may be required for installation are: ZE9050 - AMS-9050 Planning Guide, 8200-0537-01. Note: There may be installation restrictions on antennas in certain countries.
PAGE 2
About the Product The AMS-9050 controller is part of an EAS system that: - Includes pedestal type antennas. - Deters theft by activating an alarm when it detects the unique response of an active Ultra•Max hard plastic tag or disposable label when its signal is picked up by an antenna. - Connection for hardwired sync and transmit inhibit function. - Supports RS-232 (local diagnostics) and RS485 (remote diagnostics). - Supports RS-485 network communication to antennas (if supported by antenna).
PAGE 3
Device Connections AC IN (120Vac/ 240Vac) System Status LED RS-232 SERVICE (J2) Pin 1 - Rx Pin 2 - Tx Pin 3 - Ground Pin 4 - Ground RELAYS (P54) Pin 1 - Common 1 Pin 2 - NC 1 Pin 3 - NO 1 Pin 4 - ‘X’ (shield) Pin 5 - Common 2 Pin 6 - NC 2 Pin 7 - NO 2 Pin 8 - ‘X’ (shield) RS-485 NETWORK (P8) Pin 1 - Black Pin 2 - Red Pin 3 - X (Shield) RMT ALARM 1 (P64) Pin 1 - Orange Pin 2 - Violet Pin 3 - X (Shield) RMT ALARM 2 (P63) Pin 1 - Orange Pin 2 - Violet Pin 3 - X (Shield) WIRED Tx SYNC (P2) Pin 1 - Black
PAGE 4
Device connections consist of: - Transceiver connectors - Antenna alarm/Communication connectors - Receiver connectors - Relay connectors - Remote alarm connectors - RS-485 network connector - Wired Tx sync connector - Wireless AC sync connector - RS-232 service connector. Transceiver connectors (P58, P59, P88, P91). These four connectors support Tx/Rx antennas designated A, B, C, and D. The tables below show connections for various antenna configurations.
PAGE 5
Preliminary IMPORTANT! DIP S1 and DIP S2 are located on the circuit board of the controller. When connecting antennas, set switches 1–8 of each DIP according to the number and type of antennas used. Antenna alarm/Communication connectors (P92, P93, P97, P100): Four connectors support the antennas audio/visual alarms, transmitter/ alarms inhibit function, and peripheral RS-485 network communication. Table 1.
PAGE 6
Preliminary Relay connectors (P54): The controller has two double-pole, double-throw (DPDT) relays, each configurable using service configurator software. Each relay: - Triggers devices such as externally powered remote alarms, time-lapse VCRs, and security cameras; one device per detection zone. - Accepts three wires and a shield. Cable shields share one pin on the connector.
PAGE 7
Preliminary Installation Features Wired Synchronization The AMS-9050 controller provides the following installation features: If a wired Tx sync device is connected to the controller, the controller automatically uses its signal as the timing reference instead of the ac line. The service configurator indicates that wired sync is active. - Auto Synchronization - Wired Synchronization - Transmitter Current Control - Controller Mounting.
PAGE 8
Preliminary Internal diagnostics: Service Features The AMS-9050 controller provides the following service features: - The service configurator displays the operating current for each antenna. Operating current is 15A peak for all countries. - The service configurator displays ambient temperature within the controller. - The hardware supports software with a remote command to reset the system. Hardware within the controller protects it from runaway software.
PAGE 9
Preliminary AC Requirements Installation Requirements WARNING—RISK OF ELECTRIC SHOCK! During installation, if the antenna must be left unattended, turn off power or cover high voltage components to prevent unauthorized access to hazardous voltages. Verifying Equipment and Unpacking - Verify that all equipment has arrived. Ensure the system configuration is correct for the site. Unpack major components in a back room. At the install site, lay out parts in the order used.
PAGE 10
Preliminary Mounting the Controller ! WARNING! Do not mount controller with its fan or cable tray face up. The controller can be mounted as follows: - On a shelf. - On a wall. DO NOT mount the controller with its fan facing up! - To a ceiling. Plywood with a surface larger than the controller is secured to the ceiling studs that hold the drywall. The controller then attaches with suitable hardware to the plywood.
PAGE 11
Preliminary AC Hookup Controller Installation 1. Choose a power cord for the country of use. Tools required: - USA-IEC 320, 18/3, 125V, 10A, 7.5ft. Schuko-IEC 320, 1mm sq., 250V, 10A, 2.5m UK-IEC 320, 1mm sq., 250V, 10A, 2.5m Japan-IEC 320, 2mm sq., 250V, 15A, 2.5m US-Filter, Line, 125V, 6A, Plug-in Australia to IEC 320, 2.5m, 250V, 10A Tape measure Pencil or marker Electric drill Phillips-head screwdriver or bit Hand vacuum or broom 2. Plug in the power cord.
PAGE 12
Preliminary System Setup Verifying Operation 1. Ensure controller power is off. Check that the antenna alarm lamp lights when a tag/label is passed through the checkout aisle, or if the system is covering adjacent aisles, that the lamp lights only in the aisle the tag/label was in. 2. Connect antenna cables to the controller according to how the antennas are intended to perform. Refer to diagrams and tables on pages 3 and 4 of this guide.
PAGE 13
Preliminary Alert Codes Troubleshooting Note: Should the electronics require servicing or replacement, detach the electronics from the cable access panel as follows: 1. Loosen the four top screws and detach the cover from the controller. 2. Unplug all cable connectors and the ac power cord. 3. Remove six screws securing the cable access panel to the controller. 4. On the left side of the controller, loosen the two screws holding the controller to the wall. 5.
PAGE 14
Preliminary Local Diagnostics Remote Diagnostics The AMS-9050 controller enables you to troubleshoot and change controller parameters using your laptop computer and the ADS 4 service configurator. The AMS-9050 controller enables you to use an RS-485 network to troubleshoot and change controller parameters from a remote site. To connect to the network, connect the laptop, modem and accessories as shown below. The cables connect to the RS-485 connector inside the controller using a T adapter.
PAGE 15
Preliminary Fuse Replacement Specifications The controller has two 2.5A, 250V slow-blow fuses in the IE320 ac receptacle. Electrical POWER SUPPLY Fuses (2) Primary input ............................ 100-120Vac or 200-240Vac @ 50–60Hz Primary power fuse .................. 2.5A, 250V, slo-blow, hi-breaking Current draw (120V)................. <1.5Arms Current draw (240V)................. <1Arms Input power (120V)................... <130W Input power (240V)................... <123W 1.
PAGE 16
Preliminary Other Declarations Declarations WARRANTY DISCLAIMER: Sensormatic Electronics Corporation makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
PAGE 17
Preliminary AMC-7000 Integrated Metal Foil Detection Installation Guide AMC-7000 About the Product The AMC-7000 Integrated Metal Foil Detection kit (ZPMETAL-DET) is an AMS-9050 option that detects metal with a large surface area, such as aluminum foil, when it passes between the pedestals of a system. It is designed to not detect metal objects with small continuous surfaces, such as keys and shopping carts. The kit can only be used with AMS-9050 controllers and only for dualpedestal 2m systems.
PAGE 18
Preliminary Wiring the AMC-7000 Installation The AMC-7000 Metal Foil Detection kit (ZPMETALDET) consists of the following: Part Metal detection enclosure Mounting bracket, Left Mounting bracket, Right Tx/Rx cable Power supply/RS-485 cable Wired Sync Connector assy, Aux/WS (5-pin) Connector assy, Alarm/comm (8-pin) Romex conduit connector Nut Qty.
PAGE 19
Preliminary Wiring the AMS-9050 Controller Connect the following cables to the AMS-9050 controller. Refer to Figure 1and Figure 2.
PAGE 20
Preliminary Figure 1. Cabling diagram for Metal Foil Detection, AMS-9050, and Ultra•Exit antennas P92 Ant A Alarms P58 Ant A Tx 1 2 3 4 5 6 7 8 Shield Yellow Orange Blue Violet Black Red Green 1 2 3 4 5 Black Red Shield Green White AMS-9050 Com cable * 0652-0243-01 AMC-7000 Metal Foil Detection Board AMS-9050 Tx/Rx cable * 0652-0242-01 Black Red Shield Green White AMS-9050 Controller 1 P1 2 Ant. 1 3 IN 4 5 Ant.
PAGE 21
Preliminary Figure 2. Metal Foil Detection board pinout P7 (Peripheral RS-485) Pin 1 - Black Pin 2 – Red Pin 3 - Shield (Per. 485 Lo) (Per. 485 Hi) (Ground) P6 (Peripheral RS-485) Pin 1 - Black Pin 2 – Red Pin 3 – Shield P9 (Relays) (Per. 485 Lo) (Per.
PAGE 22
Preliminary Figure 3. Photograph of connections on Metal Foil Detection board and AMS-9050 Controller P5 P14 P8 P2 (WIRED SYNC) P64 (DIGITAL REM. ALARM) P97 (ALARMS B) P4 P92 (ALARMS A) P2 P93 (ALARMS C) P1 P3 P58 (TX A) P88 (TX C) * Dashed lines above indicate connectors that are connected by cable. AMC-7000 INTEGRATED METAL Foil DETECTION INSTALLATION GUIDE 8200-2609-01, REV.
PAGE 23
Preliminary 3. Mount the AMS-9050 to the wall or ceiling. See Figure 5. Mounting the AMC-7000 The AMC-7000 enclosure can be mounted either on top of the AMS-9050 controller or next to it. Mounting next to the controller The AMC-7000 enclosure can be mounted next to the controller. See Figure 4. • To ensure the cables can reach from the enclosure to the controller, do not mount the enclosure more than 15cm (6in) from the controller.
PAGE 24
Preliminary Figure 5. Mounting the AMC-7000 on an AMS-9050 controller Plywood sheet (for ceilingmounted installations) For drywall mount – Use 23kg (50lb) drywall anchors (not supplied) and 32mm (1-1/4in) #8 screws (not supplied) For ceiling mount – Use 32mm (1-1/4in) #8 screws (not supplied) Mounting brackets AMC-7000 enclosure AMS-9050 cover screws (supplied with controller) Nuts AMC-7000 INTEGRATED METAL Foil DETECTION INSTALLATION GUIDE 8200-2609-01, REV.
PAGE 25
Preliminary b. Click on the button label Metal Connect. Downloading Files You must download the appropriate hex files for the Metal Detection option. 1. Connect your service laptop to the system at a service port on the AMS-9050 controller, the antenna, or the Metal Detection enclosure. Note: if you connect to the antenna or controller, the system will not be able to alarm because of metal or alarms while the laptop is connected. 2.
PAGE 26
Preliminary Figure 6. Metal Detection configuration screen Configuring the Metal Detection Settings On the Metal Detection screen in the configurator, you read the level indicators and then configure the appropriate settings for the site. 1. Configure the environment as it will be when the store is open. Move any racks to their normal place, open doors if they are open during the day, etc. 2. Click on the Metal Detection tab. The Metal Detection configuration screen appears. See Figure 6.
PAGE 27
Preliminary • No. Go to Step 11. Arrow) and cause a metal detection alarm but not exceed the Inhibit Threshold (Blue Arrow)? 11. Does the site have doors with metal in them that permanently open into the detection zone during the day and remain closed at night (or vice versa)? • Yes. Go to Step 5. No. Go to Testing the System To test a system for its ability to detect foil-lined bags, use the Foil Bag Simulator. • Yes. Go to the Setting the Smart Threshold procedure. 1.
PAGE 28
Preliminary 13. Repeat this procedure for any other pedestal pairs that have metal detection. 5. When the Foil Bag Simulator goes through the field, does the Rx Sum rise above the Inhibit Threshold (Blue Arrow), which causes the system to fail to alarm? Trouble-Shooting If the system is either failing to detect metal or false alarming, use the following procedure to determine the cause and correct it. a. Enable Cart Inhibit and raise Inhibit Threshold to a value above the high point of the Rx Sum. 1.
PAGE 29
Preliminary Configuring the Alarm Settings On the Setup screen, configure the Lamps, Relays, and Audio settings to the appropriate values for the site. Table 1. Configuring relays If Relay 1 is And Relay 2 for a ___ is for a ___ event … event… Note: the relays you configure with the Relays parameters are the relays in the AMS-9050 controller at P54, not the relays on the Metal Detection Board at P9.
PAGE 30
Preliminary Specifications Declarations Electrical Power Supply Primary Input: ............................. 12V DC (-4V;+8V) Power Req. ..................................................... < 3W Relays Regulatory Compliance EMC ...............................................47 CFR, Part 15 Contact Form:.................................................DPDT Rated Load:............ 0.5A at 125VAC; 1A at 30VDC Max. Operating Voltage:............. 125VAC; 110VDC Max. Switching Capacity: ...................
PAGE 31
Preliminary About the Product” on page 1. X X X X Other Declarations WARRANTY DISCLAIMER: Sensormatic Electronics Corporation makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.