User's Manual

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsanti theft device

Company Confidential

AMS-9040 Controller

Installation and Service Guide

Contents

To the Installer....................................................... 1

About the Product.................................................. 2

Operation ........................................................... 2

Device Connections ........................................... 3

Installation Features........................................... 7

Service Features................................................ 8

Installation ............................................................. 9

Installation Requirements .................................. 9

Installation Procedure ...................................... 10

Power Connections.......................................... 13

Sample Hookups.............................................. 14

Troubleshooting................................................... 15

System Status Alert Codes.............................. 15

Laptop/Modem Connections............................ 16

Fuse Replacement........................................... 17

Specifications ...................................................... 18

Declarations ........................................................ 18

Appendix A: About Auto Sync ........................... 19

To the Installer

This installation and service guide explains how to

install, setup, and service the AMS-9040 controller.

Parts required to install this system are:

- AMS-9040 Controller (ZEAISLEPP)

- Digital AM antennas (various)

- Extension bracket 0500-9792-01 (optional)

- AMS-9040 Controller Keyswitch (optional)

Other documents that may be required for

installation are:

- Planning Guide, 8200-0367-01

- Antenna Installation Guide (various)

- Antenna Controller Keyswitch, 8200-0367-04

Note:

- Because customer requirements dictate the

placement of system components, your

Sensormatic representative will supply this

information separately.

- If this product was installed in a European

Union or European Free Trade Association

member state, please give the Declaration of

Conformity included with this product to the

manager or user. By law, this information must

be provided to the user.

- There may be restrictions on the installation of

certain antennas in certain countries. Please

see the antenna installation guides for

documentation of the restriction.

AMS-9040 CONTROLLER 8200-0367-02, REV. 9

INSTALLATION AND SERVICE GUIDE

1 of 20

Summary of content (20 pages)

PAGE 1
Company Confidential AMS-9040 Controller To the Installer Installation and Service Guide This installation and service guide explains how to install, setup, and service the AMS-9040 controller.
PAGE 2
Company Confidential Operation About the Product The controller deters theft by activating an alarm when it detects the unique response of an active Ultra•Max hard plastic tag or disposable label. The AMS-9040 controller is part of a four-channel EAS detector used to detect EAS tags/labels at store exit(s). The controller: - Supports transceiver (Tx/Rx) antennas, auxiliary receiver antennas, and noise coils in any combination up to the maximum specified.
PAGE 3
Company Confidential Device Connections General-Purpose Connections (P27, P29, P31, P33) Connector pin assignments are listed on pages 4 and 5.
PAGE 4
Company Confidential A label inside the controller identifies connectors. SERVICE (RS232) (Behind Cover) Cables pass into enclosure through here.
PAGE 5
Company Confidential Continued from previous page REMOTE ALARMS (P7) Pin 1 - 12V return Pin 2 - 12V alarm Pin 3 - Alarm 0 Pin 4 - 12V return Pin 5 - 12V alarm Pin 6 - Alarm 1 Pin 7 - Shield (Alarm 0/1) Pin 8 - NC RELAYS C-D (P9) Pin 1 - C (Relay C) Pin 2 - NC (Relay C) Pin 3 - NO (Relay C) Pin 4 - White with an 'X' (Relay C Shield) Pin 5 - C (Relay D) Pin 6 - NC (Relay D) Pin 7 - NO (Relay D) Pin 8 - White with an 'X' (Relay D Shield) WIRED Tx SYNC (P2) RELAYS A-B (P12) Pin 1 - Black (Tx Burst High) Pi
PAGE 6
Company Confidential Wireless AC Sync Connection (On Controller) Remote Alarm Connections (P7) This connector can power and control up to two remote alarms, such as a ZC30 or ZC35. Protected by a cover plate, this connector receives a cable from a Sync Link device which, when connected, is automatically used as the timing reference for system functions. See “Automatic AC Line Synchronization” on page 7. Also, see Appendix A.
PAGE 7
Company Confidential Installation Features Controller-Assisted Antenna Tuning Installation features are as follows: A series of LEDs on the tuning circuit board of a digital AM antenna indicate to field personnel when and where tuning jumpers are to be placed for optimum antenna performance. For specific information, see the installation guide supplied with the antenna.
PAGE 8
Company Confidential Service Features Internal Diagnostics Service features are as follows: The controller provides the following internal diagnostics: - Laptop computer service configurator - Internal diagnostics - - The service configurator displays operating current for each antenna. LED status indicator - Remote diagnostics via modem, Ethernet, or RS485 network. Must have external converter to support Ethernet. The service configurator displays ambient temperature within the controller.
PAGE 9
Company Confidential Installation Mounting limitations are as follows: Installation Requirements - Mounting options are mounting directly to two metal or wood wall studs, mounting indirectly to a wood board attached to two metal or wood studs, mounting to drywall using suitable hardware that can support the weight, or placing the controller on a shelf. - The wall must support 29.2kg (64.6 lbs) or four times the weight of the controller assembly.
PAGE 10
Company Confidential Installation Procedure 3. Thread cable clamps into the holes. Run cables (except power) through the cable clamps leaving about 30cm (12in) of excess on the other side. Tighten the clamps. This section describes installation procedures for when the controller is to rest on a shelf, or be attached to a wall or ceiling. 4.
PAGE 11
Company Confidential Wall Mounting 5. If using cable clamps: Thread cable clamps into the holes. Run cables (except power) through the cable clamps leaving about 30cm (12in) of excess on the other side. Tighten the clamps. WARNING! The wall must be able to support 29.2kg (64.6 lbs). 1. Remove the cover from the top of the controller, then detach the integral cable tray/mounting bracket assembly from the controller. Two captive ¼-turn fasteners secure the assembly.
PAGE 12
Company Confidential Ceiling Mounting 4. Of the 19 knockouts in the cable tray dedicated to cables, remove the ones closest to the connectors they are associated with. DO NOT remove the three knockouts used to access the ac connection area. Observe Class 2, Class 2 “wet”, and Class 3 requirements. WARNING! The ceiling must be able to support 29.2kg (64.6 lbs). 1. Remove the cover from the top of the controller, then detach the integral cable tray/mounting bracket assembly from the controller.
PAGE 13
Company Confidential Power Connections Hardwired Cable Ac power connects to the controller using a power cord or hardwired cable. CAUTION: Use only copper wire. - The power source can be 100-120Vac or 220-240Vac. Referring to the figure below: - The controller automatically senses the voltage so no jumper settings are required. 1. Remove one of the three knockouts accessing the ac connection area in the cable tray. Thread a cable clamp into the hole.
PAGE 14
Company Confidential Sample Hookups Because antennas and equipment can be connected to the controller in various ways based on the number of store exits involved, security zones required, coverage desired, and customer preferences, system configurations are too numerous to describe in this document. Instead, study the sample systems shown in this section to provide a feel for how to connect these devices. (TBD) AMS-9040 CONTROLLER INSTALLATION AND SERVICE GUIDE 8200-0367-02, REV.
PAGE 15
Company Confidential When a status alert occurs, the LED indicator changes color and pattern. Red is used for serious or critical system alerts while yellow is for less serious alerts and warnings. Troubleshooting System Status Alert Codes - The number of red flashes identifies a digit in a two-digit error code (for example, four flashes is the number four). The start of an error code is indicated by a long LED interval.
PAGE 16
Company Confidential Laptop/Modem Connections 37 Ped C Tuning TX Off 38 Ped D Tuning TX Off 39 Sequence Table Mismatch 41 Missing Zero Crossing 42 Wired Sync: Missing Signal 43 Temperature Fault • External modem 44 S/W Temperature Fault • DB25 male to RJ12/RJ11 female connector 45 PWM Fault • RJ11 male to RJ10 male cable 46 Fan Fault 49 Realtime Error Procedure 51 Autosetup Owner Timeout 52 Autosetup Release W/O Lock 1. Prepare the DB25 to RJ12/RJ11 null modem connector.
PAGE 17
Company Confidential Fuse Replacement The controller contains two 5A, 250V, slow-blow fuses. To replace the fuse(s) in the controller, do the following: Fuses (2) 1. Detach the controller from the cable tray. Two screws secure the tray, one on each side. 2. On the controller, pry the rectangular cover plate from the IEC320 receptacle using a small slotted screwdriver. Two spring-loaded fuses should pop out. 3. Replace the blown fuse (or fuses) with 5A, 250V slow-blow fuses (P/N 5111-0028-11). 4.
PAGE 18
Company Confidential Specifications Declarations Electrical Regulatory Compliance EMC .............................. 47 CFR, Part 15 EN 300330-1 U1.3.2 (2002) ETSI EN 300330-2 V1.1.1 (2001-06) ETSI EN 301489-3 V 1.2.1 (2000-08) ETSI EN 301489-1 V 1.2.1 (2000-08) RSS210 Power Supply Primary input ............................100-120Vac or 220-240Vac @ 50–60Hz Primary power fuse...................5A, 250V, slo-blow, hi-breaking Current draw.............................4.0Arms @ 120Vac Input power ........
PAGE 19
Company Confidential Appendix A: About Auto Sync Too much ambient noise. During initialization, the controller determines if EAS transmitters are nearby. If noise in the environment prevents the location other transmitters and if this is the first power on of the controller, the delay is set to zero. If this is not the first power on of the controller, the zero crossing delay is retrieved from storage within the controller and the service configurator displays “Too Much Noise”.
PAGE 20
Company Confidential AMS-9040 CONTROLLER INSTALLATION AND SERVICE GUIDE 8200-0367-02, REV.