User's Manual

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsANTI THEFT DEVICE

AMS-1080 DETECTION SYSTEM 8200-0418-01, REV. A

INSTALLATION AND SERVICE GUIDE

1 of 18

AMS-1080

Detection System

Installation and Service Guide

Contents

To the Installer....................................................... 1

About the Product.................................................. 2

Device Connections .............................................. 4

Installation Features.............................................. 6

Service Features ................................................... 7

Installation Requirements...................................... 8

AMS-1080 Antenna Installation............................. 9

Against a Wall or Counter .................................. 9

To a Railing Post.............................................. 10

Controller Installation........................................... 12

AC Hookup .......................................................... 12

System Setup ...................................................... 13

Antenna Connections....................................... 13

Software Selections ......................................... 14

Verifying Operation.............................................. 14

Troubleshooting................................................... 15

Fuse Replacement .............................................. 17

Specifications ...................................................... 17

Declarations ........................................................ 18

To the Installer

This installation and service guide explains how to

install, setup, and service the AMS-1080 detection

system.

Parts required to install this system are:

- AMS-1080 Controller

- AMS-1080 Controller Mounting Kit

0352-0203-01 (optional)

- AMS-1080 Antenna(s)

- AMS-1080 Antenna Counter Mounting Kit(s)

0352-0199-01 or Pole Mounting Kit(s)

0352-0198-01

- ZKRANGER-DG Ranger antenna kits, as

required (purchase separately).

Other documents that may be required for

installation are:

- AMS-1080 Planning Guide, 8200-0418-02

- ZKRANGER-DG Ranger Installation Guide,

8200-0452-01

- AMS-1080 Theory or Operation, 8200-0418-03.

Note:

- Because customer requirements dictate the

placement of system components, your

Sensormatic representative will supply this

information separately.

- If this product was installed in a European

Union or European Free Trade Association

member state, please give the Declaration of

Conformity included with this product to the

manager or user. By law, this information must

be provided to the user.

- The controller is cooled by a fan that is factory

set to 240Vac. If using 120Vac, remove the

cover from the controller and change fan

jumpers to 120Vac. See label inside the

controller for jumper locations.

- Install the AMS-1080 antenna at least 5cm (2in)

from metal surfaces.

Summary of content (18 pages)

PAGE 1
To the Installer AMS-1080 Detection System This installation and service guide explains how to install, setup, and service the AMS-1080 detection system. Installation and Service Guide Parts required to install this system are: - AMS-1080 Controller - AMS-1080 Controller Mounting Kit 0352-0203-01 (optional) - AMS-1080 Antenna(s) - AMS-1080 Antenna Counter Mounting Kit(s) 0352-0199-01 or Pole Mounting Kit(s) 0352-0198-01 - ZKRANGER-DG Ranger antenna kits, as required (purchase separately).
PAGE 2
- About the Product Up to two individual pairs of adjacent aisles (A1/A2 and B1/B2) supported. The AMS-1080 detection system detects EAS tags/labels in food store checkout aisles, with each aisle independently supported.
PAGE 3
Basic Operation AMS-1080 Antenna Features The AMS-1080 detector deters theft by activating an alarm when it detects the unique response of an active Ultra•Max hard plastic tag or disposable label. The AMS-1080 antenna features the following: To detect a tag/label, AMS-1080 antenna(s) connected to the controller emit a magnetic field close to the tag/label’s natural frequency causing it to vibrate or “ring” at the frequency of the field.
PAGE 4
Device Connections Tx 1 TRANSMIT ANTENNA (P58) Tx 2 TRANSMIT ANTENNA (P59) Pin 1 - Black (Figure-8 return) Pin 2 - Red (Antenna A2) Pin 3 - White with an 'X' (Shield) Pin 4 - Green (Aiding return) Pin 5 - White (Antenna A1) Pin 1 - Black (Figure-8 return) Pin 2 - Red (Antenna B2) Pin 3 - White with an 'X' (Shield) Pin 4 - Green (Aiding return) Pin 5 - White (Antenna B1) AUX. RECEIVE (P56A) AUX. RECEIVE (P56B) Pin 1 - Black (Ant C1, noise can.
PAGE 5
Transmit Antenna (Tx1, Tx2) RS-232 Network (Service Connection) These two connectors each receive a transmit cable from an AMS-1080 antenna. This 4-pin modular connector receives the cable from a modem or laptop computer used to communicate with the controller. Receive Antenna (Rx1, Rx2, Aux A, Aux B) RS-485 Network This connector supports network communication and Sensormatic alarm logging and traffic flow devices.
PAGE 6
Installation Features Too much ambient noise. During initialization, the controller locates other nearby EAS transmitters. Controller - If ambient noise prevents the controller from locating nearby EAS controllers and if this is the first power on of the controller, transmitter delay is set to zero. - If this is not the first power on of the controller, the zero crossing delay stored in the controller is used.
PAGE 7
Internal Diagnostics Service Features - The service configurator displays the operating current for each antenna. Operating current is 15A peak for European or non-European countries. - The service configurator displays ambient temperature within the controller. - The hardware supports software with a remote command to reset the system. - Hardware within the controller protects it from runaway software.
PAGE 8
AMS-1080 Antenna Requirements Installation Requirements ! Verifying Equipment and Unpacking - - Verify that all equipment has arrived. Ensure the system configuration is correct for the installation site. Unpack major components in a back room. At the install site, lay out parts in the order you will need them. Do not clutter the aisle or cause a trip hazard. WARNING! Do not install this device where highly combustible or explosive products are stored or used.
PAGE 9
IMPORTANT! Keep the antenna at least 5cm (2in) from metal surfaces. As necessary, add spacers and adjust the mounting base assembly to maintain this separation. AMS-1080 Antenna Installation The AMS-1080 antenna can be mounted against a wall or counter, or to a railing post. Spacer Against a Wall or Counter For this installation, the antenna is secured to the floor and top edge of the checkout counter. Tools required: - Tape measure and level Pencil or marker Knife Electric drill and drill bits: 5.
PAGE 10
4. Drill mounting holes. PROCEDURE 1. A label is on a bottom side panel of the AMS1080 antenna. The label must face the counter. a. Using a 5.5mm (7/32in) masonry bit, drill two holes in the floor 54mm (2-1/8in) deep for the anchor bolts. 2. Attach antenna clamps. CAUTION: If carpet exists, use a knife to remove it from under the mounting base to prevent carpet runs caused by drilling. a. Position clamps in the spaces on the antenna designated for them. b. A right and left spacer are provided.
PAGE 11
To a Railing Post 2. With the label on the bottom side panel of the antenna facing Aisle A1 or Aisle B1, with the antenna parallel to the line of traffic and its bottom 17.8cm (7in) from the floor, drill a 16mm (5/8in) cable access hole in the railing post directly opposite where cables exit the antenna. For this installation, the antenna is secured to a railing post between two adjacent aisles. CAUTION: Do not drill this hole through the other side of the post. 3. Attach the pole bracket to the antenna.
PAGE 12
Controller Installation AC Hookup Tools required: - CAUTION: Fan voltage is factory set for 240Vac. If using 120Vac, remove the cover from the controller and change fan jumpers to 120Vac. See label inside the controller for jumper locations. Tape measure Pencil or marker Electric drill and drill bits: 5.5mm (7/32in) and 9.5mm (3/8in) Phillips-head screwdriver or bit Hand vacuum or broom PROCEDURE 1. Choose a power cord for the country of use. Power cords come in .9m (3ft), 2.7m (9ft), 3.
PAGE 13
- System Setup Turn on the controller. Then connect antenna cables and select software parameters as follows for the type of antenna configuration installed. AMS-1080 antenna set up as a transmitter and positioned between two adjacent aisles for zone detection. A1/A2 B1/B2 A1/A2 B1/B2 Antenna Connections - Connect antenna cables as follows: AMS-1080 antenna set up as a transceiver.
PAGE 14
Software Selections Verifying Operation Note: Software parameters are selected using AMS-1080 service configurator software. Only selections pertaining to a basic system setup are covered here. For additional information on software parameters and how to use the configurator, click Help in the service configurator.
PAGE 15
Alert Codes Troubleshooting System Status Alert Codes The Status LED on the controller displays system status alert codes. When an alert code occurs, the LED changes color and pattern. Red is used for serious alerts while yellow is used for those less serious. a. The number of red flashes identifies a digit in a two-digit alert code (for example, four flashes is the number four). The start of an alert code is indicated by a long LED interval.
PAGE 16
Local Diagnostics Remote Diagnostics The AMS-1080 controller enables you to troubleshoot and change controller parameters using your laptop computer and the AMS-1080 service configurator. The AMS-1080 controller enables you to use an RS-485 network to troubleshoot and change controller parameters from a remote site. To connect to the network, connect the laptop, modem and accessories as shown below.
PAGE 17
Fuse Replacement Specifications The controller has two 2A, 250V slow-blow fuses in the IE320 ac receptacle. Electrical POWER SUPPLY Primary input ............................ 100-120Vac or 200-240Vac @ 50–60Hz Primary power fuse .................. 2A, 250V, slo-blow, hi-breaking Fuses (2) Current draw ............................ <1.0Arms @ 120Vac Input power .............................. <100W TRANSMITTER Operating frequency................. 58kHz (±200Hz) Transmit burst duration ............ 1.
PAGE 18
Other Declarations Declarations WARRANTY DISCLAIMER: Sensormatic Electronics Corporation makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.