Install Guide

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsANTI-PILFERGAE DEVICE

Preliminary

ZBAMB9010-IPS EAS LABEL DEACTIVATION CONTROLLER 8200-0747-24 REV. 3A

INSTALLATION GUIDE

1 OF 7

ZBAMB9010-IPS EAS

Label Deactivation

Controller

Installation Guide

TYPE: AMB-9010-IPS

If you need assistance…

For product bulletins, the most recent updates to

this document, or to contact a technical support

specialist, visit www.sensormatic.com/support.

About this Guide

This guide only covers hardware installation. For

setup information, see the setup guide for the

deactivation pad or coil being connected.

About the Product

European Regulatory Restriction:

None.

Declaration of Conformity: If this

product was installed in a European

Union or European Free Trade

Association member state, give the

Declaration of Conformity included with

this product to the manager or user. By

law, this information must be provided to

the user.

Intended Use: Only install this device

as described in this guide.

See page 4 for additional

WARNINGS and CAUTIONS.

Product Description

The ZBAMB9010-IPS deactivation controller

connects to a Sensormatic

low inductance

deactivation pad or coil to deactivate Ultra•Strip

low energy security labels.

A Status LED on the deactivator is solid green

when power is applied.

Installation Options

 On the countertop as described in this guide.

 ZBSMP-B1 Under-Counter Mounting Bracket.

See installation guide 8200-0054-03.

 ZPSTP-RA Remote Alarm Module See

installation guide 8200-0838-01.

Mechanical Specifications

Dimensions (L x W x H) ............... 26.2cm (10.3in) x

22.1cm (8.7in) x

10.1cm (4in)

Weight .......................................... 2.5kg (5.5 lbs)

Power cable length ....................... 18.3m (6ft)

Summary of content (7 pages)

PAGE 1
Preliminary About the Product ZBAMB9010-IPS EAS Label Deactivation Controller European Regulatory Restriction: None. Installation Guide Declaration of Conformity: If this product was installed in a European Union or European Free Trade Association member state, give the Declaration of Conformity included with this product to the manager or user. By law, this information must be provided to the user. TYPE: AMB-9010-IPS Intended Use: Only install this device as described in this guide.
PAGE 2
Preliminary Deactivation pads and coils used with the controller: Deactivation Pad Consists of one or two coils inside a horizontal housing Deactivation Coil A vertical or horizontal coil in a standalone housing or inside a barcode scanner Internal features:     Automatic deactivation coil detection Auto and re-synchronization Adjustments to transmit and deactivation fields Status LED for power on, communication activity, and basic diagnostics.  EAS Label type (SR/DR).
PAGE 3
Preliminary Setup Networking A Deactivation Universal Configurator is used to setup the controller. This configurator: A network port provides the ability to enable an external Sensormatic device such as an LDM II to send data to a store’s POS network using the RS485 port for the purpose of remote diagnostics or data mining. The external device must be programmed with special software.  Installs on a laptop computer that plugs into the SERVICE port.
PAGE 4
Preliminary PRECAUTIONS Please read the following precautions for:  Safety Cleaning  Cleaning  Device interaction Wipe the housing with a soft cloth moistened (not soaked) with mild detergent. Then wipe off excess.  Installation. SAFETY Keep spills from entering the housing. DO NOT USE:  Spray cleaners.  Ammonia- or chlorine-based cleaning solutions; they may damage the housing or corrode internal parts.  Abrasives, solvents, or flammable liquids. WARNING! Hazardous areas.
PAGE 5
Preliminary Installation The controller can be placed on the countertop, or using an optional ZBSMP-B1 mounting bracket attached to the underside of the countertop or sidewall of the counter. ! WARNING! When the controller is mounted to a sidewall of a counter, its cable connectors MUST NOT face down. Procedure CAUTION: To avoid damaging the controller:  Perform the next three steps in order. DO NOT reverse the steps.  DO NOT plug or unplug any cable with power on. 1.
PAGE 6
Preliminary Specifications Connector Inputs/Outputs Electrical Each Network RS485 Port (8 pin modular jack) Voltage input to power supply............................ 100–240Vac, 50/60Hz (±5%) Voltage input from power supply ....................... 22.5Vdc Pin 1: RS485 HI (RS-485 Driver A) Pin 2: RS485 LO (RS-485 Driver B) Pin 3: Universal Sync A (RS-485 Driver A) Pin 4: +5V* (Configurator controlled on/off, 250mA max.) Pin 5: Spare +5V* (Configurator controlled on/off, 250mA max.
PAGE 7
Preliminary FCC COMPLIANCE: This equipment complies with Part 15 of the FCC rules for intentional radiators and Class A digital devices when installed and used in accordance with the instruction manual. Following these rules provides reasonable protection against harmful interference from equipment operated in a commercial area.