Install Guide

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsWIRELESS LR-WPAN IN 2.4 GHz BAND USING DIGITAL SS.

PRELIMINARY

ZBAMB2070 MOBILE HANDHELD DEACTIVATOR 8200-0958-01, REV. 1B

USER GUIDE

1 of 16

ZBAMB2070 Mobile

Handheld Deactivator

(Motorola MT2070 Handheld Scanner)

Installation Guide

IMPORTANT! Before You Begin!

This device contains many unique parts.

Before you go to the installation site,

watch the Mobile Handheld Deactivator

training video on the LMS site at

https://mytycohr.com, or on Yammer “Tyco

Retail Solutions Global Training Group” at

https://www.yammer.com/tyco.com.

Contents

Required Parts and Tools ...................................... 2

Installation .............................................................. 3

Troubleshooting ................................................... 13

Maintain the Product ............................................ 14

Specifications ....................................................... 15

Declarations ......................................................... 16

Note: Because customer requirements may dictate

the placement of specific components, your

Sensormatic representative will supply this

information separately.

Motorola MT2070

Handheld Scanner

ZBAMB2070 EAS

Deactivator Module

Assembly (dark

shaded parts)

Motorola MT2070

Base Charging Station

Summary of content (16 pages)

PAGE 1
PRELIMINARY Contents ZBAMB2070 Mobile Handheld Deactivator Required Parts and Tools ...................................... 2 Installation .............................................................. 3 Troubleshooting ................................................... 13 Maintain the Product ............................................ 14 Specifications ....................................................... 15 Declarations .........................................................
PAGE 2
PRELIMINARY Required Parts and Tools EAS Deactivator Module EAS Module Rear Adapter S1 (2x) EAS Module Front Adapter ZBAMB4415 S3 S2 W ZBAMB4410 S1 (2x) S3 (2x) EAS Power Supply 5606-0096-01 (plus 0352-0460-xx power cord) S2 (2x) W (2x) 2 in a box Lithium Battery Kit 0352-0594-01 (3.7V, 2.2Ah, with leads) ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 3
PRELIMINARY Installation Step 1. Prepare the Motorola scanner gun 1a WARNING: Remove the battery to prevent accidental exposure to laser radiation during assembly. Save the battery. You will re-install it at the end of this procedure. Press and slide switch to release. 1b T8x60 (2x) Use a T8x60 Torx wrench to remove the Motorola MT2070 bumper (save parts to give later to Loss Prevention Manager). Scanner Gun ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 4
PRELIMINARY Step 2. Attach the scanner gun to the EAS Deactivator Module 2a 2. Press in place. Tight fit. Apply moderate pressure to secure. 1. Push down. 2b S1 (2x) Use a 3/32in hex wrench. ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 5
PRELIMINARY Step 3. Prepare the Motorola Base Charging Station 3a Detach the Motorola Base Charging Station from the counter by removing the center screw and/or Velcro, if any. 3b Remove the Motorola interlock and power supply cables. 3c Remove and save screws. Re-install in Step 4c. 2x ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 6
PRELIMINARY Step 4. Modify the Motorola Base Charging Station (Part 1) 4a 4b Squeeze tabs to detach the Motorola Front Adapter. Give the part to the Loss Prevention Manager. Install the ZBAMB4415 EAS Front Adapter. 4c Secure EAS Front Adapter by reinstalling screws removed in Step 3c. 2x ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 7
PRELIMINARY Step 5. Modify the Motorola Base Charging Station (Part 2) 5a Turn the locking screw counter-clockwise. 5b Press the ZBAMB4415 EAS Rear Adapter onto the Motorola Base Charging Station until it “clicks”. Note: Leave the locking screw in its counter-clockwise position. ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 8
PRELIMINARY Modify the Motorola Base Charging Station (Part 2), continued 5c 5d Thread the EAS power supply cable into the bottom of the EAS Rear Adapter. Plug the EAS Power supply into a protected AC outlet. 5606-0096-01 EAS Power Supply ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 9
PRELIMINARY Step 6. Modify the Motorola Base Charging Station (Part 3) 6a Route the EAS power supply cable through the cable channel in the Motorola Base Charging Station. Tape cables in place where shown. 6b Re-connect the Motorola interlock and power supply cables. Tie wrap cables 6c EAS (Blue LED) Verify that power is supplied to both the deactivator module and to the Motorola Base Charging Station. Motorola (Blue LED) ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 10
PRELIMINARY Step 7. Secure the Motorola Base Charging Station In the order shown, secure the Base Charging Station at the customer’s preferred location (see example below). Secure the front adapter first, then the rear adapter. 2. 3. S2 (2x) S3 (2x) 1. W (2x) Use to level the base charging station. Example of Mounting Location A mounting plate may be required if the mounting surface is uneven. Order Mounting Plate Kit 0352-0588-01. ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 11
PRELIMINARY Step 8. Install the EAS battery 8a 8b Barcode label Holding the battery with its barcode label facing up, plug in the battery cable. Remove the screw and battery cover. 8c Bend wires as shown. ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8d Install the battery cover and secure with the screw. DO NOT over tighten. 8200-0958-01, REV.
PAGE 12
PRELIMINARY Step 9. Re-install the battery into the Motorola scanner gun Step 10. Pair the scanner gun to the Base Charging Station Scan the barcode on the Motorola Base Charging Station to pair the scanner. Look for lightning bolt symbol on the LCD. LED/Audio sequence: Red > Beep > Green. ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 13
PRELIMINARY Step 11. Charge the battery in the EAS Deactivator Module Charge for 8 hours before first use.
PAGE 14
PRELIMINARY Maintain the Product Field Replaceable Parts A complete parts list is available online at: http://www.sensormatic.com/support/techsupport/. Login, then click the Part Information link on the Tech Support home page. Part Number ZBAMB4410 EAS Deactivator Module ZBAMB4415 EAS Module Rear Adapter 5606-0096-01 Power Supply, EAS Module Rear Adapter 0352-0460-xx Power Cord, Power Supply, EAS Module Rear Adapter ZBAMB2070 MOBILE HANDHELD DEACTIVATOR USER GUIDE 8200-0958-01, REV.
PAGE 15
PRELIMINARY Battery Specifications Battery type................. Rechargeable lithium ion polymer 2200 mAh (max. 4.3V, nominal 3.7V) Electrical AC input ........................................ 100–240V @ 47-63Hz DC Input ................................................... 12Vdc @ 2.5A Operating temperature ................ 32 to 122°F (0 to 50°C) Storage temperature ............... -40 to 158°F (-40 to 70°C) Charging temp. .............
PAGE 16
PRELIMINARY Declarations Other Declarations Regulatory Information FCC ID: BVCAMB44 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.